Sdera POWER AWNING REGAL HEAD PA
_ SPEAKER REPLACEMENT z
AWNINGS
Purpose
This document describes the removal and replacement of the speaker in the Solera® Power Awning Regal
Head (Fig. 1).
Resources Required
+ 1-3 people, depending on task. + Appropriate drive bits
+ Putty stick or similar tool + Zip ties
+ Cordless or electric drill or screw gun
Fig. 1
@
G
=S& =<
DS DB
ss ==
= =
ao
®)
Regal Idler head with speaker Regal Drive head with speaker
The “CAUTION” symbol above is a sign that a safety risk is involved and may cause personal injury and/or
product or property damage if not safely adhered to and within the parameters set forth
in this manual.
Moving parts can pinch, crush, or cut. Keep clear at all times.
Rev: 06.24.24 Page 1 CCD-0003685

Sdera POWER AWNING REGAL HEAD HH
SPEAKER REPLACEMENT ch
ey (YuiPPERT =
AWNINGS
Instructions
The following instructions apply to the drive and idler heads with speakers.
Removal
1. Extend the awning about 12" away from the unit.
Failure to secure the outer arms may result in personal injury, product or property damage.
Pressure from the gas strut can cause the outer arm to kick open, which could cause injury, product
or property damage.
2. Secure both support arm assemblies by running a zip tie around the outer arm and around the pin on
the top of the mount arm where the mount arm and inner arm connect (Fig. 2).
Fig. 2
Y/Y? bs
«| @ oF
.
=Y 6
=
3. Usea putty stick or similar tool to slide in between the grill cover and main body of the head cover.
Start in one corner and work your way around the grill cover (Fig. 3) until all four sides have been
released. Set aside for later use.
NOTE: Grill cover attaches with plastic tabs.
Fig.3
— 2 | 4 ih
= i |
Underside of Speaker Grill Cover
Rev: 06.24.24 Page 2 CCD-0003685

Sdera POWER AWNING REGAL HEAD PA
SPEAKER REPLACEMENT ct
oy (YuiPPERT =
AWNINGS
4. With the grill cover (Fig. 3) removed, remove the rubber foam gasket from the top of the speaker (Fig. 4).
5. There is a small tab (Fig. 4) in each corner of the open cavity that the actual speaker sets in. Remove
the speaker and determine if there is enough slack in the wires to pull the speaker out far enough
to disconnect it from the main harness. If there is enough slack, remove the speaker and go to the
Installation section. If unable to disconnect the speaker wires from the main harness go to step 6.
Fig. 4
S _
= i @&
Grill Cover }
oO :
¢
Speaker Wires Q @
py .
Rev: 06.24.24 Page 3 CCD-0003685

Sdera POWER AWNING REGAL HEAD a
SPEAKER REPLACEMENT ch
wy QYLiPPERT =
AWNINGS
6. Remove the two screws (Fig. 5) on the back of the head cover. Separate the front cover from the back
(Fig. 6). Disconnect speaker.
NOTE: The shell is made of a plastic molding, which consists of plastic tabs (Fig. 6) and notches that snap
together.
Fig.5 Fig.6
—
: |
:
A :
x |
|
« i
u —
Installation
1. Install the new speaker into the speaker bed routing the wires back through the bottom hole in the
speaker bed.
2. Reconnect the speaker wires to the main harness.
3. Place the foam gasket over the speaker.
4. Snap the previously-removed speaker grill cover back in place.
5. Reinstall the front cover to the rear cover and secure with screws.
When cutting the zip tie, hold the outer arm so it doesn't kick open. Pressure from the gas strut can cause
the outer arm to kick open, which could cause personal injury or product damage.
6. Remove the zip tie holding the arm in place.
7. Fully retract and extend awning to ensure proper drive head and motor installation and operation.
Asa supplier of a broad array of highly-engineered components in the recreation and transportation product markets, safety, education and customer satisfaction are
our primary concerns. Should you have any questions, please do not hesitate to contact us at 432-LIPPERT (432-547-7378) or by email at [email protected]
Self-help tips, technical documents, product videos and a training class schedule are available at lippert.com or by downloading the LippertNOW app.
Rev: 06.24.24 Page 4 CCD-0003685