NHTSA ID Number: 11001931
Manufacturer Communication Number: fsd-12-4_0524.pdf
TSB/Document Date: 2024-06-20
Summary
Tesla
does not provide physical owner's manual copies. Instead, all available owner’s manual content is integrated into the vehicle software, and only the content relevant for a given vehicle, based on vehicle configuration and software version installed, is displayed on its touchscreen. This file contains all available owner’s manual content for the vehicle converted to PDF format, and given the distribution method and NHTSA’s submission format requirements, it is the best available representative copy of owner’s manual content. However, a customer who accesses the owner’s manual via their vehicle’s touchscreen would only see the parts of this PDF file that are relevant to their vehicle.
CAUTION: It is your responsibility to be observant of the vehicle and it's surroundings. Ensure the area is clear when
lifting and lowering CybertruckModel SModel XModel 3Model Y and that the doors, front trunk, and liftgaterear
trunktailgate are closed as necessary to avoid damage.
CAUTION: DO NOT lift from under the Battery or side rails. Place the lift arm pads under the designated body lift points
only. The locations shown are the only approved lifting points for CybertruckModel SModel XModel 3Model Y. Lifting at
any other points can cause damage. Damage caused by incorrectly lifting CybertruckModel SModel XModel 3Model Y
is not covered by the warranty.
Jack Mode
WARNING: Failure to enable Jack Mode can result in the vehicle self-leveling, resulting in damage, injury, or death.
If CybertruckModel SModel XModel 3Model Y is equipped with air suspension, it automatically self-levels, even when the
vehicle is "asleep" and the touchscreen is powered off. To prevent damage when jacking or lifting the vehicle, you must
activate Jack mode to disable self-leveling. Jack mode prevents the self-leveling that occurs automatically.
CybertruckModel SModel XModel 3Model Y automatically self-levels, even when the vehicle is "asleep" and the touchscreen
is powered off. Before enabling Jack Mode:
1. Set the Suspension to Very High to allow for enough ground clearance for the jack.
2. Enable Jack Mode (Controls > Service > Jack Mode).
3. To deactivate Jack Mode, press the brake pedal and touch Controls > Service > Jack Mode again. Jack Mode automatically
cancels when you start to drive.
When CybertruckModel SModel XModel 3Model Y is in Jack Mode mode, a red air suspension indicator lights
up on the instrument panel.
NOTE: Jack mode may be unexpectedly enabled in situations where an object is supporting the vehicle's weight (for example
the bumper of the vehicle is resting on a curb).
794
Owner's Manual
Owners Manual
Parts and Accessories
Parts, Accessories, and Modifications
Use only genuine Tesla parts and accessories. Tesla performs rigorous testing on parts to ensure their suitability, safety, and
reliability. Purchase these parts from Tesla, where they are professionally installed and where you can receive expert advice
about modifications to CybertruckModel SModel XModel 3Model Y. Accessories are available for purchase from Tesla stores
or online at www.tesla.com.
NOTE: Some accessories may not be available in your market region.
Tesla is unable to assess parts manufactured by other distributors and therefore accepts no responsibility if you use non-Tesla
parts on CybertruckModel SModel XModel 3Model Y.
WARNING: Installing non-approved parts and accessories, or performing non-approved modifications, can affect the
performance of CybertruckModel SModel XModel 3Model Y and the safety of its occupants. Any damage caused by
using or installing non-approved parts, or by performing non-approved modifications, is not covered by the warranty.
WARNING: Tesla does not accept liability for death, personal injury or damage that occurs if you use or install nonapproved accessories or make non-approved modifications.
Accessory Wheels and Tires
If your CybertruckModel SModel XModel 3Model Y is fitted with Tesla accessory wheels or tires, the Gross Axle Weight
Rating (GAWR), wheel, tire, and loading information may be different from the labels shown on the vehicle. Refer to the
relevant following section for updated information.
NOTE: If your vehicle is not fitted with Tesla accessory wheels or tires (it is fitted with the factory original wheels and tires,
including Tesla genuine replacement parts), refer to the labels attached to the center door pillar for the most accurate
information for your CybertruckModel SModel XModel 3Model Y.
20" Sport Wheels
Wheels
20"
Owner's Manual
Location
Width (in)
Offset (mm)
Front/Rear
8.5
40
795
Owners Manual
Tires (front/rear)
Michelin, Pilot Sport 4S (PS4S)
Size
Tire Pressure
235/35ZR20
42 PSI (290 kPa)*
*Increase the tire pressure to 44 PSI (300 kPa) prior to driving 136 mph (220 kph) or faster.
GAWR
Front
2407 lbs
1,092 kg
Rear
2,767 lbs
1,255 kg
19" Sport Wheels
Wheels
19"
Location
Width (in)
Offset (mm)
Front/Rear
8.5
40
Tires (front/rear)
Size
Tire Pressure
Continental, ProContact RX
235/40R19
42 PSI (290 kPa)*
Hankook Ventus S1 Evo3
235/40R19
42 PSI (290 kPa)*
Pirelli Winter Sottozero 3
235/40R19
42 PSI (290 kPa)
*Increase the tire pressure to 44 PSI (300 kPa) prior to driving 134 mph (215 kph) or faster.
GAWR
Front
2,447 lbs
1,110 kg
Rear
2,767 lbs
1,255 kg
796
Owner's Manual
Owners Manual
20" Zero-G Wheels (Performance)
Wheels
Location
Width (in)
Offset (mm)
20"
Front/Rear
9
34
Tires (front/rear)
Size
Tire Pressure
Michelin, Pilot Sport 4S (PS4S)
235/35ZR20
42 PSI (290 kPa)
Michelin PS Cup 2
245/35ZR20
42 PSI (290 kPa)
GAWR
Front
2,650 lbs
1,202 kg
Rear
2,784 lbs
1,263 kg
20" Zero-G Wheels (Non-Performance)
Location
Width (in)
Offset (mm)
20"
Front/Rear
9
40
Tires (front/rear)
Michelin, Pilot Sport 4S (PS4S)
Size
Tire Pressure
235/35ZR20
42 PSI (290 kPa)
GAWR
Front
2,650 lbs
1,202 kg
Rear
2,784 lbs
1,263 kg
19" Gemini Wheels (Performance)
See Removing and Installing Aero Covers on page 754 for information on how to remove and install Gemini wheel covers.
Owner's Manual
797
Owners Manual
Wheels
19"
Location
Width (in)
Offset (mm)
Front/Rear
8.5
35
Tires (front/rear)
Size
Tire Pressure
Hankook Ventus S1 Evo3
235/40R19
42 PSI (290 kPa)*
Pirelli Winter, Sottozero 3
235/40R19
42 PSI (290 kPa)*
*Increase the tire pressure to 44 PSI (300 kPa) prior to driving 136 mph (220 kph) or faster.
GAWR
Front
2510 lbs
1,141 kg
Rear
3,023 lbs
1,374 kg
798
Owner's Manual
Owners Manual
18" Aero Wheels
Wheels
18"
Location
Width (in)
Offset (mm)
Front/Rear
8.5
40
Tires (front/rear)
Size
Tire Pressure
Michelin, Primacy MXM4
235/45R18
42 PSI (290 kPa)
Michelin, Pilot Sport 4 (PS4)
235/45R18
42 PSI (290 kPa)
Pirelli Winter Sottozero Serie II
235/45R18
42 PSI (290 kPa)
GAWR
Front
2,447 lbs
1,110 kg
Rear
2,840 lbs
1,288 kg
Body Repairs
If your CybertruckModel SModel XModel 3Model Y is in a collision, contact Tesla or a Tesla-approved Body Shop to ensure
that it is repaired with genuine Tesla parts. Tesla has selected and approved body shops that meet strict requirements for
training, equipment, quality, and customer satisfaction.
Some repair shops and insurance companies might suggest using non-original equipment or salvaged parts to save money.
However, these parts do not meet Tesla's high standards for quality, fit and corrosion resistance. In addition, non-original
equipment and salvaged parts (and any damage or failures they might cause) are not covered by the warranty.
Replacing Cabin Filters
NOTE: Depending on your vehicle's date of manufacture, screw may be in a slightly different location on the cabin filter cover.
Model 3 has air filters that prevent pollen, industrial fallout, road dust, and other particles from entering the cabin through the
vents. Tesla recommends replacing these filters every 2 years (every year in China). Cabin filters can be purchased at the Tesla
Shop.
To replace the cabin filters:
Owner's Manual
799
Owners Manual
1. Turn off the climate control system.
2. Move the front passenger seat fully rearwards and remove the front passenger floor mat.
3. Use a clip pry tool to carefully release the push clips that secure the front passenger footwell cover to the instrument panel.
Then, while supporting the footwell cover, disconnect the two electrical connectors and move the footwell cover aside.
◦ For the light, carefully press down on the tab while releasing the connector.
◦ For the speaker, carefully angle the vehicle-side connector so that the small tab releases from the hole in the footwell
cover-side connector while releasing the connector.
CAUTION: To avoid damage, do not pull on the wires when disconnecting the connectors. When disconnecting the
connectors, make sure to pull from the plastic on the connectors themselves.
4. Working from top-to-bottom, use a trim tool to carefully release the right side panel from the center console.
5. Remove the T20 screw that secures the cabin filter cover to the heating, ventilation, and air conditioning (HVAC) module,
then release the cabin filter cover and move it aside. On some vehicles, the screw is a T20/6mm hybrid fastener. Locking
tabs may also replace the screw: use your index finger and thumb to squeeze the two tabs at the bottom of the cabin filter
cover. Tilt the cover outward to remove.
NOTE: If the HVAC module does not have a cabin filter cover, reinstall the trim panels and contact Tesla.
WARNING: Do not stretch, bend, or otherwise damage the orange High Voltage (HV) cables that are attached to the
cabin filter cover. If the HV cables are damaged, immediately discontinue this procedure. HV shock can result in
serious injury or death.
800
Owner's Manual
Owners Manual
6. Fold the upper cabin filter’s tab upward and the lower filter’s tab downward.
7. Holding the tab on the upper cabin filter, pull the upper filter out from the HVAC module.
8. Holding the tab on the lower cabin filter, pull the lower filter upwards and then out from the HVAC module.
9. Ensuring that the arrows on both new filters face towards the rear of the vehicle, insert the lower cabin filter into the HVAC
module and lower it into place. Then, insert the upper cabin filter above it.
10. Fold the tabs inward so that the cabin filter cover can be installed.
11. Install the cabin filter cover by engaging the lower cover tab then securing the T20 screw or T20/6mm hybrid fastener.
Tighten the screw to 1.2 Nm/0.89 ft-lbs. On vehicles with tabs instead of a T20 screw: maneuver the top notch of the cabin
filter cover into place, then secure the tabs at the bottom of the HVAC module.
12. Reconnect the two electrical connectors to the components in the front passenger footwell cover, then resecure the cover
with the push clips.
13. Align the right side panel with the front and rear locator slots on the center console, then apply pressure until all of the
clips are fully secure.
14. Reinstall the front passenger floor mat then move the front passenger seat back into place.
Replacing Cabin Filters
Model Y has air filters that prevent pollen, industrial fallout, road dust, and other particles from entering the cabin through the
vents. Tesla recommends replacing these filters every 2 years (every year in China). Cabin filters can be purchased at the Tesla
Shop.
To replace the cabin filters:
1. Turn off the climate control system.
2. Move the front passenger seat fully rearwards and remove the front passenger floor mat.
3. Use a clip pry tool to carefully release the push clips that secure the front passenger footwell cover to the instrument panel.
Then, while supporting the footwell cover, disconnect the two electrical connectors and move the footwell cover aside.
◦ For the light, carefully press down on the tab while releasing the connector.
◦ For the speaker, carefully angle the vehicle-side connector so that the small tab releases from the hole in the footwell
cover-side connector while releasing the connector.
CAUTION: To avoid damage, do not pull on the wires when disconnecting the connectors. When disconnecting the
connectors, make sure to pull from the plastic on the connectors themselves.
Owner's Manual
801
Owners Manual
4. Working from top-to-bottom, use a trim tool to carefully release the right side panel from the center console.
5. Remove the 6 mm screw that secures the cabin filter cover to the heating, ventilation, and air conditioning (HVAC) module,
then release the cabin filter cover and move it aside. On some vehicles, tabs replace the 6 mm screw: use your index finger
and thumb to squeeze the two tabs at the bottom of the cabin filter cover. Tilt the cover outward to remove.
6. Fold the upper cabin filter’s pull tabs outward.
7. Holding the tabs on the upper cabin filter, pull the upper filter out from the HVAC module.
8. Holding the upper tab on the lower cabin filter, pull the lower filter upwards and then out from the HVAC module.
9. Ensuring that the arrows on both new filters face towards the rear of the vehicle, insert the lower cabin filter into the HVAC
module and lower it into place. Then, insert the upper cabin filter above it.
10. Fold the tabs inward so that the cabin filter cover can be installed.
11. Install the cabin filter cover by engaging the lower cover tab then securing the 6 mm screw. Tighten the screw to 1.2 Nm/
0.89 ft-lbs. On vehicles with tabs instead of a 6 mm screw: maneuver the top notch of the cabin filter cover into place, then
secure the tabs at the bottom of the HVAC module.
12. Reconnect the two electrical connectors to the components in the front passenger footwell cover, then resecure the cover
with the push clips.
802
Owner's Manual
Owners Manual
13. Align the right side panel with the front and rear locator slots on the center console, then apply pressure until all of the
clips are fully secure.
14. Reinstall the front passenger floor mat then move the front passenger seat back into place.
Replacing Cabin Air Filters
CybertruckModel SModel XModel 3Model Y has an air filter that prevents pollen, industrial fallout, road dust, and other
particles from entering the cabin through the vents. Tesla recommends replacing these filters every 2 years (every year in
China). Cabin filters can be purchased at the Tesla Shop.
To replace the cabin filter:
1. Turn off the climate control system.
2. Move the front passenger seat fully rearwards.
3. Slowly and gently pull down the footwell cover to release the magnets, then disconnect the electrical harness on the right
side of the cover. Set the footwell cover aside.
4. Squeeze the cabin filter door lock to release it, and then remove and set the door aside.
5. Note the direction of air flow printed on the cabin filter. The arrows on the filter should face toward the rear of the vehicle.
6. Slide the filter out of the HVAC module.
7. Ensuring that the arrows on the new filter face toward the rear of the vehicle, insert the new cabin filter into the HVAC
module.
8. Slide the cabin filter door onto the HVAC module, and then push the door to lock it.
NOTE: Ensure the lock is fully engaged and the door is sealed shut.
9. Position the front passenger footwell cover on the vehicle and connect the electrical harness to the cover.
10. Install the front passenger footwell cover, making sure the magnets (x3) are locked into position.
11. Move the front passenger seat back to its original position.
Replacing the Low Voltage Lead-Acid Battery
This procedure is intended for vehicles in North America only.
CAUTION: It is your responsibility to monitor the low voltage battery health. Damage to the low voltage battery due to
running out of range is not covered by the warranty.
CAUTION: To avoid damage that is not covered by the warranty, replace your low voltage lead-acid battery with the
same type of battery. The low voltage lead-acid battery for North American vehicles is AtlasBX / Hankook 85B24LS 12V
45Ah. You can purchase a new lead-acid low voltage battery that is compatible with your vehicle from your local service
center
NOTE: Vehicles manufactured between approximately July 2017 and October 2020 do not have a heat pump and should use
Vehicles Manufactured Before Approximately October 2020 on page . Vehicles manufactured afterward have a heat
pump and should use Vehicles Manufactured After Approximately October 2020 on page .
NOTE: Vehicles manufactured in Gigafactory Shanghai before approximately October 2021, and in the Fremont Factory before
approximately December 2021, are equipped with a Lead-Acid low voltage battery. Vehicles manufactured after these dates
are equipped with a Lithium-Ion low voltage battery. Before performing this procedure, it is your responsibility to double
check and confirm whether your vehicle is equipped with a Lead-Acid or Lithium-Ion low voltage battery.
Vehicles Manufactured Before Approximately October 2020
Perform the following procedure to replace the lead-acid low voltage battery. Wear appropriate personal protection
equipment (such as safety glasses, leather gloves when handling the lead-acid battery etc.).
Removal:
1. Prepare the vehicle to remove the low voltage lead-acid battery:
a. Ensure the vehicle is in Park.
b. Lower all windows.
Owner's Manual
803
Owners Manual
c. Open the front trunk.
d. Leave a door propped open so you can get back into the vehicle if needed.
e. Disconnect the charge cable from the charge port.
2. Move the driver and front passenger seat fully forward.
3. Under the rear seat, press the left and right tabs to the side and lift the seat cushion up. The seat separates from the base
but is still restrained by one wire harness on each side.
4. Disconnect the wire harnesses and remove the seat cushion. Set the cushion aside.
5. In the front trunk, remove the vehicle’s underhood apron by inserting a small, non-marring flat tool or your fingers
underneath the panel. Pull up to loosen the clips and set the underhood apron aside.
804
Owner's Manual
Owners Manual
6. Remove the cabin intake duct and set it aside.
7. Power off the vehicle by navigating to Controls > Safety > Power Off on the touchscreen.
8. With a 10mm socket, loosen the nut that secures the negative (-) terminal clamp to the negative (-) post on the low voltage
lead-acid battery. Release the terminal clamp from the negative (-) post.
9. Disconnect the low voltage cable from penthouse:
a. In the rear passenger seat, remove the foam cover and set it aside. The foam covers the low voltage cable.
Owner's Manual
805
Owners Manual
b. Release and pull down the gray lever-arm on the side of the low voltage connector.
c. Pull the connector upward to disconnect it from the penthouse.
WARNING: The area under the seat cushion houses the high voltage Battery. DO NOT TOUCH OR PLACE ITEMS ON
THE METAL HOUSING! Doing so can cause serious damage or injury.
10. With a 10mm socket, release the terminal cover and loosen the nut that secures the positive (+) terminal clamp to the
positive (+) post on the low voltage lead-acid battery. Release the terminal clamp from the positive (+) post and cover the
terminal clamp with a dry rag.
806
Owner's Manual
Owners Manual
CAUTION: Do not allow the positive (+) terminal clamp to contact nearby components like the low voltage battery
hold down bracket or A/C cooling lines.
11. Unplug the vent tube hose from the negative (-) terminal side of the low voltage lead-acid battery.
12. With a 10mm socket, loosen the nut and release the battery hold down from the top of the low voltage lead-acid battery by
unhooking and sliding it back, taking care to ensure it does not slip into the vehicle.
13. Using the battery handle, carefully remove the low voltage lead-acid battery, taking care not to touch or damage the
surrounding components.
WARNING: When lifting the low voltage lead-acid battery, stand in front of the vehicle and use proper lifting
technique. The low voltage battery weighs approximately 25 lb (12 kg). Failure to do so may cause serious injury.
Owner's Manual
807
Owners Manual
14. Inspect the new low voltage lead-acid battery to ensure it is equipped a red plug on the positive (+) terminal side. If the
new low voltage battery does not have a red plug, use a small trim tool transfer the red plug from the old battery to the new
one.
CAUTION: Dispose of the old low voltage lead-acid battery according to local laws, such as dropping it off at a
battery recycling facility. Keep the low voltage battery upright and place it on a towel or piece of cardboard when
transporting it.
Installation:
1. Remove the protective caps from the positive (+) and negative (-) posts on new low voltage lead-acid battery.
2. Carefully maneuver the new low voltage battery into place, taking care not to touch or damage nearby components.
3. Install the low voltage battery hold down and use a 10mm socket to tighten the bolt that secures it to the low voltage leadacid battery. Torque the bolt to 6 Nm (4.4 ft-lb).
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: fsd-12-4_0524.pdf
Replacement Service Bulletin Number:
MFR Communication Date: 2024-04-30
MFR Internal Campaign ID/Software Version: fsd-12-4
Communication Type: Over The Air
NHTSA Components: UNKNOWN OR OTHER
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.