SERVICE BULLETIN
Subject: New Decals Location in Engine Room

Bulletin Type:

Bulletin No: TS35-FC-2401

PQR No: 500000007290

Rev No: 00

Ref. No: 700004414

Vehicle Model: TS 35

Flat Rate Time / Code: 105 min

Date of issue: 23.01.2024

Modify Before: 23.01.2025

What to do with off coming parts:

What to do with outstanding parts of previous
revision:

☐Scrap

☐Return
☐Use with additional parts
☐On consignment
No off coming parts

☒

Description of the modification:
Belt guard was phased out. So, decals which were
located on the belt guard moved to a new location.

Bulletin Responsible: Musa Akalın

Published & Approved By: Cihan Yaycıoğlu

Field Fix Conditional

☐Scrap
Return
☐Use with additional parts
☐On consignment
No outstanding parts

☐
☒

SERVICE BULLETIN
SAFETY INSTRUCTIONS
1. Mechanical Requested Dress Code
WARNING:
 Dress properly to avoid personal injury and damage to the
vehicle






Always wear protective clothing
Do not wear any worn or loose-fitting clothing
Remove jewelry before starting to work
In case of long hair, use hairnet
The illustration on the left shows some of the correct and
incorrect clothing
 Sharp edged items should be avoided in order not to
scratch vehicle (i.e. belts, watches, necklace)

2. Protect Seats when Mechanic Starts Working

 Seats, trimming, upholstery stuff and carpeting should be
protected with appropriate coverings.

3. Welding on the Chassis
a. Always disconnect the batteries (starting with the negative lead).
b. Disconnect the connectors of electrical and electronic equipment (electronic control
units, sensors and actuators) if they are less than 2 meters away from the chassis
part to be welded or the earth terminal of the welding equipment.
c. The earth terminal should never be attached to vehicle components such as engine,
axles and springs. Arcing on these parts is not permitted, because of the risk of
damage to bearings, springs, etc.
d. The earth terminal must make good contact and be placed as close as possible to
the part to be welded.
e. Plastic pipes, rubber parts and parabolic springs should be well protected against
welding spatter and temperatures higher than 70°.
f. The contact switch must not be in the accessory or contact position. The contact key
should be removed.
g. Reconnect in reversed order of disconnecting. Ensure that a good earth connection
is made between chassis, engine and cab.

SERVICE BULLETIN

INCLUDED PARTS LIST
No

Part No

Part Name

Picture

Qty

Unit of
Measure

1

9325-7301Y

PANEL, LABEL

1

Piece

2

MF140005Y

BOLT,HEX,FLANGE
(M6X0.9X16 4T) K:5.8

2

Pieces

3

9050-314Y

LABEL(DRIVE AXLE
SHAFT WARNING)

1

Piece

4

9050-315Y

LABEL(USE
REFRIGERANT R-134a
ONLY)

1

Piece

5

9050-1044Y

LABEL, TRANSMISSION,
ENG-FRE

1

Piece

6

9050-302Y

LABEL(OIL STICK
AREA)(ENG-SPA)

1

Piece

7

9050-298Y

LABEL,ENGINE LID
WARNING (ENG-SPA)

1

Piece

SERVICE BULLETIN
No

Part No

Part Name

Picture

Qty

Unit of
Measure

8

9050-264Y

TS30E,TS35E,TS45 ISX12
LUB. LABEL

1

Piece

9

9050-313Y

LABEL(DONT LEAVE
RAGS IN ENGINE BAY)

1

Piece

10

9050-300Y

LABEL (ENGINE
COMPARTMENT
WARNING)

1

Piece

11

9050-633Y

LABEL, BELT TS35

1

Piece

12

9050-1073Y

LABEL, COOLANT FILLING
INSTRUCTION

1

Piece

13

TC395107Y

RIVET,BLIND (2.4X6)

28

Pieces

SERVICE BULLETIN
TECHNICAL INSTRUCTIONS
1- Open the engine cover. (See Figure-1).

Figure-1
2- Mount the label numbered 9050-314Y on the rear bumper with TC395107Y (See Figure-2).

Figure-2

SERVICE BULLETIN
3- Mount the label numbered 9050-1044Y on the oil filling bracket with TC395107Y
(See Figure-3).

Figure-3

SERVICE BULLETIN
4- Mount labels shown in the picture below on the panel numbered 9325-7425Y with TC395107Y.
(See Figure-4).

9050-315Y
9050-313Y

9050-302Y
9050-633Y
9050-1073Y
9050-300Y
9050-264Y
9050-298Y

TC395107Y

Figure-4
5-Mount the label panel numbered 9325-7301Y on the vehicle. (MF140005Y 2pc)
(See Figure-5).

Figure-5

SERVICE BULLETIN
LABOR BREAKDOWN
Application

Time

Open engine cover

5'

Mounting labels on the vehicle

20'

Mounting labels on the panel

60'

Mounting label on the vehicle

20'

Total Labor Time

105'