New: 0.91 in (23 mm)
Service limit: 0.83 in (21 mm)

Front Brake Pad Thickness (excluding back New: 0.39 in (10 mm)
plate)
Service limit: 0.12 in (3 mm)
Rear Brake Pad Thickness (excluding back
plate)

New: 0.43 in (11 mm)

Parking brake

Electrically actuated parking brake calipers

Service limit: 0.08 in (2 mm)

Suspension
Suspension

Specifications

Front

Independent, double wishbone, air spring with adaptive damper, stabilizer bar.

Rear

Independent, double wishbone, air spring with adaptive damper, stabilizer bar.

Battery - Low Voltage
Battery - Low Voltage

Specifications

Rating

4 amp hour

Voltage

48V

Battery - High Voltage
Battery - High Voltage Specifications
Type

Liquid-cooled lithium ion (Li-ion)

Nominal Voltage

700V DC

Temperature Range

Do not expose Cybertruck to ambient temperatures above 149° F (65° C) or below -22° F
(-30° C) for more than 24 hours at a time.

283

Owner's Manual

Instructions for Transporters
Instructions for Transporters
DO NOT TRANSPORT WITH WHEELS ON THE GROUND
The front motor and rear motor(s) in Cybertruck may generate power when the wheels spin. Always transport
Cybertruck with all four tires off the ground. Ensure that the tires are unable to spin at any time during transport.
WARNING: NEVER TRANSPORT YOUR VEHICLE WITH THE TIRES IN A POSITION WHERE THEY CAN SPIN.
DOING SO CAN LEAD TO SIGNIFICANT DAMAGE AND OVERHEATING. IN RARE CASES EXTREME
OVERHEATING MAY CAUSE THE SURROUNDING COMPONENTS TO IGNITE.

Do not transport Cybertruck using any method that is not specified by Tesla. Adhere to the instructions provided
here and observe all warnings and cautions. Damage caused by improper transporting of your vehicle is not covered
by the warranty.
NOTE: Tesla is not liable or responsible for reimbursing services not dispatched through Tesla Roadside Assistance.

Approved Methods for Transporting
A flatbed truck or comparable transport vehicle is the recommended method of transporting Cybertruck. Cybertruck
can face either direction on the truck bed.

CAUTION: Use a flatbed truck with a bed that is at least 21 ft (6.5 meters) long (A). Before attempting to tow
Cybertruck, always check the tow truck's recommended loading capacity against the gross vehicle weight
rating (GVWR) of Cybertruck (see Dimensions, Weights, and Cargo Capacity on page 278) to ensure that the
flatbed truck is capable.
Activate Transport Mode before repositioning Cybertruck (if necessary) and winching it onto a flatbed tow truck. For
more information, see Activate Transport Mode on page 286.
If Cybertruck has no low voltage power, attempt to jump start the low voltage system first so that you can then
activate Transport Mode. For more information about jump starting, see If Vehicle Has No Power on page 285.
Owner's Manual

284

Instructions for Transporters
CAUTION: Cybertruck uses steer-by-wire technology. As a result, you will be unable to use the steering wheel
to turn the wheels if Cybertruck has no power.
NOTE: Do not transport Cybertruck with the front or rear wheels on dollies unless absolutely necessary for a short
distance. If you are transporting Cybertruck on dollies, ensure that a steering wheel lock is applied and care is taken
to prevent the front wheels from spinning.
CAUTION: Before using dollies, check the manufacturer's specifications and recommended loading capacity
against the vehicle weight rating and axle weight rating of Cybertruck, as specified by the vehicle certification
label (see Vehicle Loading on page 274).
CAUTION: DO NOT TRANSPORT YOUR VEHICLE IF THERE IS ANY CHANCE OF ANY OF THE WHEELS
SPINNING.
CAUTION: Tesla is not responsible for any damage caused by or during the transport of Cybertruck, including
personal property damage or damage caused by using self-loading dollies or tire skates.
WARNING: Cybertruck is equipped with high voltage and low voltage components that may be compromised
as a result of a collision (see Electric Vehicle Components on page 215). Before transporting Cybertruck, it is
important to assume these components are energized. Always follow high voltage safety precautions (wearing
personal protection equipment, etc.) until emergency response professionals have evaluated the vehicle and
can accurately confirm that all high voltage systems are no longer energized. Failure to do so may result in
serious injury.

If Vehicle Has No Power
If Cybertruck has no low voltage power:
1. Open the powered frunk. See Opening the Powered Frunk with No Power on page 290.
2. Jump start the low voltage battery. See Jump Starting on page 294.
Cybertruck must have low voltage power to open the doors from the outside or use the touchscreen.
WARNING: It may be more difficult to steer Cybertruck when the vehicle is being supported by an external low
voltage power supply. The wheels may not be as responsive to the steering wheel as expected, and extreme
caution should be taken when repositioning Cybertruck.
CAUTION: Cybertruck uses a 48V low voltage architecture. As a result, some functions may be unavailable or
degraded if you are supporting Cybertruck with less than 30V (for example, another vehicle or a 12V portable
jump starter).
CAUTION: Avoid using low voltage components of Cybertruck (such as the climate control system, cabin USBC ports, lights, etc.) when the vehicle is being supported by an external low voltage power supply. Doing so
may disable low voltage systems and make it necessary to jump start Cybertruck again.
NOTE: Tow providers: If the vehicle ran out of range, see Running Out of Range on page 290 for more information
on transporting the vehicle to a charging station and preparing the vehicle to charge.
If you are unable to jump start Cybertruck and the touchscreen is not accessible, use tire skates to re-position the
rear tires, keeping front tires on the ground. When using tire skates, be sure to use skates of sufficient size to avoid
contact between the tire and the bed/pavement. Before using tire skates, always check the manufacturer's
specifications and recommended loading capacity.

Disable the Self-Leveling Air Suspension System
NOTE: If Cybertruck has no low voltage power (or is being supported by an external low voltage power supply) you
will not be able to enter Jack Mode.
Your Cybertruck is equipped with an air suspension system that automatically self-levels, even when the vehicle is
"asleep" and the touchscreen is powered off. To prevent damage, you must activate Jack Mode to disable selfleveling:
1. Touch Controls > Ride and Handling on the touchscreen.
2. Press the brake pedal, and then touch Medium to maximize ride height.
3. Touch Controls > Service > Jack Mode.

285

Owner's Manual

Instructions for Transporters
NOTE: Jack Mode cancels if you touch the button again or when driving speed exceeds 4 mph (7 km/h).

Activate Transport Mode
Transport Mode keeps the parking brake disengaged while winching Cybertruck onto a flatbed truck. When active,
Transport Mode displays a message indicating that the vehicle will remain free-rolling. The following are required to
enable Transport Mode:
• Low voltage power. If Cybertruck has no low voltage power, attempt to jump start the low voltage system so that
you can use the touchscreen to activate Transport Mode (see If Vehicle Has No Power on page 285).
• Cybertruck must detect a key. Transport Mode is available only when a key is detected.
• Ensure the vehicle is not connected to a charger. Transport Mode is not available if Cybertruck is still plugged in.
To activate Transport Mode:
1. Ensure the vehicle is in Park and that it is not connected to a charge cable.
2. Chock the tires and make sure Cybertruck is secure.
WARNING: Ensure that the wheels are secure and that Cybertruck has continuous low voltage support
while it is in Transport Mode. If there is a loss of low voltage power (for example, if the low voltage battery
does not self-recover before activating Transport Mode or if the external power supply becomes
disconnected) there is a risk of rollaway.
3. Press and hold the brake pedal, and then on the touchscreen, touch Controls > Service > Towing. The
touchscreen displays a message reminding you how to properly transport Cybertruck.
4. Touch Transport Mode. The Transport Mode button turns blue, and Cybertruck is now free-rolling and can slowly
be rolled (no faster than walking speed) for short distances or winched.
WARNING: Power steering may be disabled when Cybertruck is in Transport Mode. The steering system
may be less responsive and the steering wheel may be more difficult to turn. Use extreme caution when
repositioning the wheels of Cybertruck while in Transport Mode.
To cancel Transport Mode, touch Transport Mode again.
NOTE: Transport Mode is only intended to allow for winching Cybertruck onto a flatbed truck or repositioning the
vehicle out of a parking space. While in Transport Mode, the tires are allowed to rotate slowly (under 3 mph or 5
km/h) and for a very short distance (less than 30 feet or 10 meters). Exceeding these boundaries can lead to
significant damage and overheating that is not covered by the warranty.
NOTE: If you are unable to activate Transport Mode (because, for example, the electrical system is not working and
you are unable to jump start the low voltage system), use tire skates to reposition Cybertruck. Before doing so,
always check the manufacturer's specifications and recommended loading capacity.

Pull onto the Flatbed Truck From the Rear
To pull Cybertruck from the rear, use the tow hitch:
1. Chock the tires.
2. Remove the rear tow hitch cover. See Accessing the Trailer Hitch Assembly on page 140.
3. Attach the winch cable to the cutouts on either side of the tow hitch.

Owner's Manual

286

Instructions for Transporters

4. Activate Transport Mode. See Activate Transport Mode on page 286.
NOTE: If Cybertruck has no low voltage power, you will need to jump start it before activating Transport Mode.
See If Vehicle Has No Power on page 285.
5. Remove the tire chocks.
6. Pull Cybertruck slowly onto the flatbed truck.
7. If Cybertruck is in Transport Mode, deactivate it by touching Transport Mode again.

Pull onto the Flatbed Truck From the Front
To pull Cybertruck onto a flatbed truck from the front, use one or both of the square tow hooks beneath the front
fascia:
1. Chock the tires.
2. Attach the winch cable to the tow hook(s). Either one or both tow hooks can be used.

3. Activate Transport Mode. See Activate Transport Mode on page 286.
NOTE: If Cybertruck has no low voltage power, you will need to jump start it before activating Transport Mode.
See If Vehicle Has No Power on page 285.
4. Remove the tire chocks.
5. Pull Cybertruck slowly onto the flatbed truck.
6. If Cybertruck is in Transport Mode, deactivate it by touching Transport Mode again.

287

Owner's Manual

Instructions for Transporters
Secure the Tires
The vehicle's tires must be secured onto the flatbed using the eight-point tie-down method.
• Remove any wheel covers before securing the tires.
CAUTION: Failure to remove wheel covers before attaching tie-down straps may result in damage to the
wheel covers.
• Ensure any metal parts on the tie-down straps do not touch the face of the wheels.
• Do not place tie-down straps over body panels or through the wheels.
CAUTION: Attaching the tie-down straps to the chassis, suspension or other parts of the vehicle's body may
cause damage.

Owner's Manual

288

In Case of Emergency
Contacting Tesla Roadside Assistance
Tesla Roadside Assistance is available to you 24 hours a day, 365 days a year, for the duration of your warranty
period. Tesla Roadside Assistance is also available to speak with roadside service professionals to answer any
questions and explain the proper procedure for transporting your vehicle.
When contacting Tesla Roadside Assistance, please provide:
• The Vehicle Identification Number (VIN). The VIN is displayed when you touch Controls > Software. The VIN can
also been seen by looking through the driver's side of the windshield.
• Your exact location.
• The nature of the problem.
If available in your region, you can also expedite your request, by choosing the Roadside Assistance option in the
Tesla mobile app.
NOTE: For a detailed description of Tesla's Roadside Assistance policy, go to the support page on the Tesla web site
for your region.

Regional Phone Number(s)
Canada: 1-877-79TESLA (1-877-798-3752)
Mexico: 800-228-8145
United States: 1-877-79TESLA (1-877-798-3752)
NOTE: The phone number is also available by touching Controls > Service.

289

Owner's Manual

In Case of Emergency
Running Out of Range
CAUTION: It is your responsibility to monitor the state of the high voltage Battery and the remaining range of
your vehicle. Do not assume that there is any range available when the range displayed on the touchscreen is
at 0 miles (0 km) (or 0%). Damage to the low voltage battery due to running out of range is not covered by
the warranty.
NOTE: In the unlikely event your vehicle runs out of range while driving, pull over when safe to do so and contact
Tesla Roadside Assistance on page 289 or your preferred tow provider.
If Cybertruck runs out of range, the low voltage system is no longer supported – and when the low voltage battery
runs out of power, the vehicle cannot charge. Therefore, the low voltage system must be supported by an external
power supply to allow you to charge the High Voltage (HV) Battery. Once the vehicle begins charging, the external
power supply is no longer required.
In the case of running out of range away from a charger, the tow provider should transport Cybertruck to the nearest
charging station and unload the vehicle within the charging cable's reach. Once the vehicle is positioned next to a
charger, follow these instructions:
NOTE: If the vehicle is being transported to a charger, make sure the tow provider does not leave until confirming
that the vehicle's high voltage Battery is successfully charging.
1. Jump start the low voltage system (see Jump Starting on page 294). The low voltage battery must be jump
started to support the high voltage Battery.
2. Wait a few minutes. Once the touchscreen powers on, plug the charge cable into Cybertruck to begin charging
the high voltage Battery.
3. When Cybertruck begins to charge, disconnect the external power supply from the low voltage jump posts.
WARNING: Shut off the external power supply before removing either cable. Removing the cables while the
external power source is active may cause arcing.
NOTE: If Cybertruck is still not able to shift into Drive after charging the high voltage Battery, the low voltage
battery may need additional time to recover. Reconnect the charge cable, wait several minutes, disconnect the
charge cable, and then try again.
Before transporting to a non-Tesla charger, ensure your vehicle is equipped with an adapter that accommodates the
specific type of charging station you will be using. Even at a non-Tesla charger, you will need to jump start the low
voltage system before you can begin charging.
CAUTION: Always ensure Cybertruck has enough range for your drive, or for being stored for an extended
period. Do not rely on the range estimates displayed on the touchscreen or mobile app as range can decrease
faster than projected due to ambient temperature, driving habits, wind, vehicle settings (such as Sentry Mode),
etc.
NOTE: Towing your vehicle as a result of running out of range is not covered by the warranty.

Opening the Powered Frunk with No Power
Draft comment: btrimboli
If you make any updates to this topic, make the same updates to the DIY Guide: #unique_587 on page
In the unlikely event that Cybertruck has no low voltage power, you will be unable to open the powered frunk using
the touchscreen, mobile app, or powered frunk button.
It is necessary to open the powered frunk before attempting to jump start Cybertruck. For more information, see
Jump Starting on page 294.
To open the powered frunk when Cybertruck has no power, you need a power source that provides between 9V and
16.5V (such as a 12V portable jump starter or another vehicle), or a power source that provides between 30V and
50V. A standard 9V battery may not have enough power to open the powered frunk if Cybertruck has no power.
Instead, use a portable jump starter or another vehicle.
The steps below assume you are using an external low voltage power supply (such as a portable jump starter).
Owner's Manual

290

In Case of Emergency
NOTE: The following steps do not open the powered frunk if Cybertruck is locked and has low voltage power.
1. Locate the front trunk access terminal beneath the front-left wheel well, behind the headlights.

2. Use your finger to loosen the cover, then pull it down and toward you to remove it and expose the terminals. The
cover is attached to a loop of cable containing both the red positive (+) and the black negative (-) terminals.

3. Carefully pull the terminals out from the cavity.

291

Owner's Manual

In Case of Emergency

4. Connect the low voltage power supply's red positive (+) cable to the red positive (+) terminal.
5. Connect the low voltage power supply's black negative (-) cable to the black negative (-) terminal.

NOTE: Applying external low voltage power to these terminals only releases the front trunk latches. You cannot
power the low voltage system using these terminals.
6. If you are using a variable power supply, set the supplied voltage to a value between 9V and 16.5V or between
30V and 50V.
7. Turn on the external power supply (refer to the manufacturer’s instructions). The latches are immediately released
and you can now open the powered frunk to access the front trunk area.
CAUTION: If you are using a variable power supply, do not change the supplied voltage while the cables are
connected.
8. Shut off the external power supply.
WARNING: Shut off the external power supply before removing either cable. Removing the cables while the
external power source is active may cause arcing.
9. Disconnect both cables, beginning with the black negative (-) cable.
10. Feed the terminals back into the cavity and then press the cover gently but firmly back into place to ensure that it
is secured.

Owner's Manual

292

In Case of Emergency

293

Owner's Manual

In Case of Emergency
Jump Starting
Draft comment: btrimboli
If you make any updates to this section, make the same updates to the DIY Guide: #unique_588 on page
To jump start Cybertruck, use an external power source that is capable of supplying at least 12V, such as a portable
jump starter or another vehicle.
CAUTION: When jump starting Cybertruck, use jump cables that are 30 ft. (9 meters) or less in length. Using
cables that are longer than 30 ft. (9 meters) may result in damage to Cybertruck or to the external power
source.
The steps below assume you are using an external low voltage power supply (such as a portable jump starter). If you
are using another vehicle to jump start Cybertruck, follow the manufacturer's instructions.
WARNING: It may be more difficult to steer Cybertruck when the vehicle is being supported by an external low
voltage power supply. The wheels may not be as responsive to the steering wheel as expected, and extreme
caution should be taken when repositioning Cybertruck.
CAUTION: Cybertruck uses a 48V low voltage architecture. As a result, some functions may be unavailable or
degraded if you are supporting Cybertruck with less than 30V (for example, another vehicle or a 12V portable
jump starter).
CAUTION: Avoid using low voltage components of Cybertruck (such as the climate control system, cabin USBC ports, lights, etc.) when the vehicle is being supported by an external low voltage power supply. Doing so
may disable low voltage systems and make it necessary to jump start Cybertruck again.
CAUTION: Cybertruck cannot be used to jump start another vehicle. Doing so can result in damage.
CAUTION: Avoid short circuits when jump starting Cybertruck. Connecting cables to the wrong jump post,
touching leads together, etc., can damage Cybertruck.
1. Open the powered frunk (see Opening the Powered Frunk with No Power on page 290).
2. Remove the maintenance panel by pulling it upwards to release the trim clips that hold it in place.

3. Connect the external low voltage power supply’s red positive (+) cable to the horizontal jump post mounted next
to the brake fluid reservoir. The positive jump post is marked with a + sign.

Owner's Manual

294

In Case of Emergency

CAUTION: To avoid damaging Cybertruck, do not allow the positive cable to contact other metal
components.
4. Connect the external low voltage power supply’s black negative (-) cable to the vertical jump post. The negative
jump post is marked with a - sign. This jump post is used as a grounding location for the external support.

5. If you are using a variable power supply, set the supplied voltage to a value between 12V and 16.5V or between
30V and 50V.
6. Turn on the external power supply.
CAUTION: If you are using a variable power supply, do not change the supplied voltage while the cables are
connected. Doing so may cause damage to the vehicle.
7. Open the driver door and ensure that the touchscreen is on and the low voltage system is responsive. This may
take up to two minutes.
8. Ensure the touchscreen is on and that the low voltage system is responsive.
NOTE: If attempting to activate Transport Mode (to winch the vehicle onto a flatbed truck), leave the power
supply connected continuously until the vehicle has been secured. For more information, see Activate Transport
Mode on page 286.

295

Owner's Manual

In Case of Emergency
9. Once external power is no longer required, shut off the external power supply.
WARNING: Shut off the external power supply before removing either cable. Removing the cables while the
external power source is active may cause arcing.
10. Disconnect both cables, beginning with the black negative (-) cable.
NOTE: Cybertruck may not be able to shift into Drive until after the high voltage Battery has been charged and
the low voltage system is able to recover fully. See Running Out of Range on page 290.
11. Replace the maintenance panel by placing it back in its original location and pressing down until it is secure.
12. Close the powered frunk (see Closing on page 77).

Opening Doors with No Power
Draft comment: btrimboli
If you make any updates to this section, also update the DIY Guide: #unique_589 on page
In the unlikely event that Cybertruck has no low voltage power, you will not be able to open the doors from the
interior by pressing the interior door open buttons. Instead, use the manual door releases.
CAUTION: Manual door releases are designed to be used only in situations when Cybertruck has no power.
When Cybertruck has power, use the interior door open buttons.
WARNING: Do not use the manual door release while the vehicle is moving.

Opening a Front Door with No Power
To open a front door manually, pull up the manual door release located in front of the window switches and push the
door open.

Opening a Rear Door with No Power
To open a rear door manually, perform the following steps:
1. Remove the rubber mat on the bottom of the rear door's map pocket.

Owner's Manual

296

In Case of Emergency

2. Pull back the flap of plastic trim (if equipped), then pull the mechanical release cable forward and push the rear
door open.

297

Owner's Manual

Troubleshooting
Troubleshooting Alerts
APP_w009
Automatic Emergency Braking is unavailable
Feature may be restored on next drive
What this alert means:
The Automatic Emergency Braking feature is unavailable for the rest of your current drive. This alert does not
specifically indicate any other braking functions or features are unavailable.
This alert may be present for several reasons. Other alerts may be present for conditions that also cause Automatic
Emergency Braking to be unavailable.
What to do:
No action is typically required. Automatic Emergency Braking will usually be available again when you start your
next drive.
If this alert persists across multiple drives, or occurs with increasing frequency over several drives, it is recommended
that you schedule service at your earliest convenience.
For more information, see Collision Avoidance Assist on page 180.

APP_w048
Autopilot features temporarily unavailable
Features may be restored on next drive
What this alert means:
Autopilot features are currently unavailable on your vehicle. Depending on the configuration of your vehicle,
Autopilot features that are disabled may include:
• Autosteer
• Traffic-Aware Cruise Control
• Automatic Emergency Braking
• Forward Collision Warning
• Lane Departure Warning
What to do:
This alert can be set for several reasons. Check for additional alerts that indicate the cause of this condition.
Typically, Autopilot features are restored on your next drive. If this alert persists across multiple drives, schedule
service at your earliest convenience.
For more information and the full list of Autopilot features, see About Autopilot on page 150.

APP_w207
Autosteer temporarily unavailable
What this alert means:
Autosteer is temporarily unavailable. This could be a temporary condition caused by an external factor, such as:
• Missing or faded lane markers.
• Narrow or winding roads.

Owner's Manual

298

Troubleshooting
• Poor visibility due to rain, snow, fog, or other weather.
• Extremely hot or cold temperatures.
• Bright light due to other vehicle headlights, direct sunlight, or other light sources.
This alert will also be present if you exceeded the maximum speed limit for Autosteer with Autosteer active. In this
case, Autosteer will not be available for the rest of your current drive.
What to do:
Continue to your destination. If Autosteer is not available by the time you reach your destination, and remains
unavailable during your next planned drive, check for the following:
• Damage or obstruction caused by mud, ice, snow, or other environmental factors
• Obstruction caused by an object mounted on the vehicle, like a bike rack
• Obstructions caused by adding paint or adhesive products like wraps, stickers, or rubber coatings to your vehicle
• A damaged or misaligned bumper
If there are no obvious obstructions, or if you find damage to the vehicle, schedule service at your convenience. Your
vehicle is OK to drive in the meantime.
For more information, see Autopilot Features on page 153.

APP_w218
Autosteer speed limit exceeded
Take control of steering wheel
What this alert means:
Autosteer is unavailable because your vehicle has exceeded the maximum speed limit for this driver assistance
feature.
What to do:
Take immediate control of the steering wheel and maintain control until you reach your destination.
In most cases, Autosteer will not be available for the rest of your current drive. To reset it, bring the vehicle to a
complete stop and shift into Park. When you shift into Drive to travel to your next destination, Autosteer should be
available again.
NOTE: If this alert becomes active while you are driving in Germany, Autosteer should be available again once your
vehicle is traveling below the Autosteer speed limit.
If Autosteer is not available during your next drive, and remains unavailable throughout subsequent drives, schedule
service at your convenience. Your vehicle is OK to drive in the meantime.
For more information, see Autopilot Features on page 153.

APP_w222
Cruise control unavailable
Reduced front camera visibility
What this alert means:
Traffic-Aware Cruise Control and Autosteer are unavailable because one or more of the front cameras in your vehicle
is blocked or blinded by external conditions.
Traffic-Aware Cruise Control and Autosteer will remain unavailable while a front camera lacks adequate visibility.
Cameras may have limited or no visibility due to:

299

Owner's Manual

Troubleshooting
• Dirt or debris on the camera surface.
• Environmental conditions like rain, fog, snow, or dew.
• Bright sunlight or glare from another light source.
• Low or limited light conditions, including unlit or poorly lit roadways at night.
• Condensation (water droplets or mist) on the camera surface.
• Monotonous environmental features, including tunnel walls or highway dividers.
What to do:
Continue to your destination. Your vehicle is OK to drive.
This is often a temporary issue that clears up on its own. If the alert does not clear by the end of your drive:
• Inspect and clean the front camera area at the top center of the windshield before your next planned drive.
• Check the camera surface for condensation, dirt, or other debris and attempt to clear any obstruction.
See Cleaning a Camera on page 31 for more information on clearing dirt or debris from that area of the vehicle.
Although condensation on the inside of the front camera enclosure cannot be wiped clean, you can usually clear it
quicker by following these steps:
1. Pre-condition the cabin with the temperature set to High and A/C turned ON.
2. Turn on the front windshield defroster.
If this alert persists throughout subsequent drives but no front camera obstruction is visible, schedule service at your
earliest convenience. Your vehicle is OK to drive in the meantime.

APP_w224
Cruise control unavailable
Continue driving to allow cameras to calibrate
What this alert means:
Traffic-Aware Cruise Control and Autosteer are unavailable because the cameras on your vehicle are not fully
calibrated.
Your vehicle must maneuver with great precision when features like Traffic-Aware Cruise Control and Autosteer are
active. Before these features can be used for the first time, the cameras must complete an initial self-calibration.
Occasionally, one or more cameras can become uncalibrated.
What to do:
Continue to your destination. Your vehicle is OK to drive.
Traffic-Aware Cruise Control and Autosteer will remain unavailable until camera calibration is complete.
When calibration is complete, Traffic-Aware Cruise Control and Autosteer should be available.
For your convenience, a calibration progress indicator is displayed on the touchscreen. Calibration typically
completes after your vehicle has driven 20-25 miles (32-40 km), but the distance varies depending on road and
environmental conditions. For example, driving on a straight road with highly visible lane markings helps the
cameras calibrate quicker.
If the alert persists and camera calibration has not completed after your vehicle has driven 100 miles (160 km) or
more, or Traffic-Aware Cruise Control and Autosteer remain unavailable despite successful camera calibration,
schedule service at your earliest convenience. Your vehicle is OK to drive in the meantime.

Owner's Manual

300

Troubleshooting
APP_w304
Camera blocked or blinded
Clean camera or wait for it to regain visibility
What this alert means:
One or more of the vehicle cameras has limited visibility, or no visibility at all, due to external conditions. When the
cameras on your vehicle cannot provide accurate visual information, some or all Autopilot features may be
temporarily unavailable.
Cameras may have limited or no visibility due to: