PERFECT DELIVERY INSPECTION (PDI)

2013

A6/S6

Audi Technician Report

Client

VIN

Delivery Date

All items must be completed prior to customer delivery by an Audi technician
**Refer to the Service Work area of GFF for the PDI function tests
**Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection
**VAS Tester 5051B/5052A/6150 with Audi Brand Software 18.27 or higher
Open Campaigns/Updates
FF     Check ElsaWeb for open campaigns and updates. Perform if applicable
Battery Inspection
FF     Check battery clamps for tightness. Tighten if required
FF     Perform the A-battery test for new batteries in GFF. Scan GFF and select “No” when
prompted to run spec/actual. Select “Service work.” Select the battery test for new
batteries as part of the pre-delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current generated diagnosis protocol online.
(Note: Do not use Guided Functions. The diagnosis log will not be uploaded to GFF paperless.)
Transport Mode Deactivation, DTC check, set service reminder
FF     Deactivate vehicle transport mode (via Service Work)
FF     Scan GFF and when prompted run an SVM specified/actual comparison. Go to Function
Component Selection > SVM
FF     Set service reminder (via Service Work-17-PDI, Resetting SRI at PDI, counter reset)
FF     Set Adaptation Channel (via Service Work: 5F–Activating/Deactivating storage of music)
(applies to vehicles with an SOP after CW 22)
FF     Check engine oil level via the MMI–fill oil to the max level when the vehicle is at
operating temperature
Under the Hood Inspection
FF     Check all fluid levels and top off if necessary
Trunk Inspection
FF     Install wheel bolt cover removal tool from PDI kit into trunk lid toolkit
FF     Place the lug cap removal tool, located in the bypack, into the toolkit (where applicable)
FF     Set spare tire pressure
FF     Verify operation of trunk emergency release handle
Exterior
FF     Install permanent wiper blades unless vehicle is for inventory storage
FF     Test windshield washers for aim and function (if permanent wiper blades are installed)
FF     Turn on headlights and test headlamp washers
FF     Test exterior lighting functions
7 of 12

PERFECT DELIVERY INSPECTION (PDI)

2013 A6/S6 | Audi Technician Report

Client

VIN

Delivery Date

Exterior (continued)
FF     Check tailgate opening and closing with remote (if applicable)
FF     Check key functionality: Including seat and steering wheel position memory (if applicable);
verify vehicle starts and runs with the start/stop button; verify all doors lock/unlock with
remote and advanced key, including all door handle sensors with the advanced key (if equipped)
FF     Start/Stop info (if applicable): Verify the velum sticker is on the start/stop button.
Remove the start/stop information card from the car kit and place it in the glove box with
the owner’s manuals. Additional supply can be ordered via the Brand Store on AccessAudi
Interior
FF     Check operation of all switches: locks, windows, seat adjustment, seat ventilation/heating
(front and rear where applicable) and child safety features
FF     Rear view mirror: Check self-dimming function/lighting (if equipped)
FF     Verify operation of all interior lights, including ambient lighting
FF     Mirrors: Inspect folding, adjustments, RH tilt in reverse, and memory
FF     Inspect operation of lighter, aux. outlet under armrest, under rear vent outlets, and in luggage
compartment on passenger side
FF     Verify operation of all front and rear seat belts and latches
FF     Check horn operation
FF     Check sunroof operation (open/close/vent/deflector at edge)
FF     Turn on the night vision camera and verify operation (if equipped)
FF     Passenger side airbag: Verify operation of Passenger Occupant Detection System
Radio
FF     Verify operation of CD changer (if equipped)
FF     Verify operation of DVD player
FF     Verify operation of AMI
FF     SD card slot: Insert SD card and test function
FF     Verify HD Radio is turned “off” in Radio/Settings Menu
Audi MMI/Navigation
FF     Verify and set Language and Measurement Units in Setup Menu
FF     Set Time source setting to “GPS” and set Auto daylight savings time to “on.”
Change time zone appropriate to the dealer location
FF     Program the presets to local stations
FF     Navigation: Set dealership location (for following back to dealership during road test)
FF     Voice Activation: Press the “Talk” button and verify several commands
FF     Set the “Music volume while parking” to 6 lines (accessed via MMI rear view camera display,
Settings > Music volume while parking) (applies to vehicles with park assist or rear view camera).
FF     Rear Climate Controls: Verify heating and cooling functions and open all rear panel vents
(center & b-pillar)

8 of 12

PERFECT DELIVERY INSPECTION (PDI)

2013 A6/S6 | Audi Technician Report

Client

VIN

Delivery Date

Onboard Video Tutorials
FF     Load Onboard Video Tutorials
FF     Turn ignition on
FF     Insert the Onboard DVD into the DVD Drive
FF     Select the CAR function button. System will initialize
FF     Select the Owner’s Man. function by selecting the upper right control button
FF     Select “Yes”
FF     Select “CD/DVD”
FF     Select “Start update”
FF     Turn off ignition to start update (The update will take approx. 5 minutes)
FF     Once completed, remove the disk and place back into the case for the next vehicle
Audi connect (if equipped)
FF     Verify Audi connect Information Packet is present, including Audi brochure, T-Mobile
brochure, customer SIM card, T-Mobile Terms & Conditions (T&C)(if applicable)
FF     Connect the dealer demo SIM card to the vehicle and make sure the system fully connects to
2G or 3G (2G or 3G symbol with Box surrounding it)(only applies if in a T-Mobile service area)
FF     Enable Google Earth in the navigation settings and verify the white Google Logo appears next
to the 2G or 3G symbol
FF     Ensure the wireless network is turned on (Telephone function button > Settings Ctrl
button > Connection > Wireless network connection > select “On”)
FF     Check WiFi hotspot functionality is enabled and verify the SSID is set to “AUDIXXXX,”
where XXXX = last four digits of VIN
On-Hoist Inspection
FF     Inspect wheel bolts for proper torque using torque wrench
FF     Check underside of vehicle for fluid leaks and loose components
FF     Check steering, boots, brake system, hoses, tires and wheels for damage
FF     Install wheel bolt covers from PDI kit on all wheels
FF     Set tires to maximum recommended tire pressures listed on the B-pillar door jamb and
store tire pressure values in Car/System menu
FF     Remove Transport Blocks from shocks
FF     After removing transport blocks, secure Additional Springs (a.k.a. bump stops) by pressing
into tube of upper shock mount
Road Test
FF     Check for squeaks, rattles and wind noise
FF     Verify operation of Audi parking system plus with rear view camera and top or corner view
cameras (if equipped)
FF     Verify Vehicle Head-up Display functionality. Verify the image can be adjusted properly in the
viewing area of the windshield (if equipped)
FF     Verify engine performance and acceleration
9 of 12

PERFECT DELIVERY INSPECTION (PDI)

2013 A6/S6 | Audi Technician Report

Client

VIN

Delivery Date

Road Test (continued)
FF     Verify transmission operation, including shift paddles
FF     Verify engine start-stop system functionality (if equipped)
FF     Check steering/tire alignment
FF     Check heated steering wheel operation (if equipped)
FF     Test drive vehicle applying brakes at least 4 times at 20 mph (35 km/h) to clean brake rotors.
Check for abnormal noise/vibration
FF     Verify quality of radio reception in AM/FM/SAT bands
FF     Verify cruise control/ACC with Stop & Go functionality (if equipped)
FF     Verify Audi side assist functionality (if equipped)
FF     Verify Audi active lane assist (if equipped)
FF     Climate Control: Check heating and cooling functions and open all panel vents
FF     Seat heating and cooling (if equipped): Check for proper operation
FF     Navigation function: Activate NAV and follow directions back to dealership
FF     Verify NAV directions are visible in Head-Up Display (if equipped)
Post-Road Test Inspection
FF     Interrogate fault memory using the VAS tester and print Diagnostic Log
FF     Record final mileage on checklist and sign checklist
FF     Ensure the yellow tire pressure tag is installed on steering wheel
If Vehicle is for Showroom Display/Inventory Storage or Demo Use
FF     Install showroom charger to ensure battery remains charged at all times
FF     Apply Inventory Maintenance Sticker
FF     Install permanent wiper blades (if for showroom display or demo use)

10 of 12

PERFECT DELIVERY INSPECTION (PDI)

2013

A6/S6

Audi Vehicle Detail Report

Client

VIN

Delivery Date

WARNING: Do NOT use accessories (radio, etc.) while performing detail, as this can discharge the battery.
Refer to TSB 2009967 for Detailer responsibilities, specific use of chemicals, and for part numbers to order materials

Exterior – Prior to Delivery
FF     Remove protective covering
FF     Wash/Dry vehicle exterior including inside door jambs and under trunk
FF     Inspect painted surfaces/molding/glass and remove any residue
(If any defects [scratches/dings/dents/body damage] are found, contact your supervisor
to arrange for immediate repair)
FF     Inspect body for paint defects and damage
FF     Check interior floors, sunroof, trunk, front and rear windshield, and all windows for water leaks
FF     Apply 3M Perfect-ItTM Paste Wax
FF     Clean front and rear windshield using 3MTM Glass Polishing Compound.
Refer to TSB 2020552/2 for details
FF     Apply 3M Performance Finish wax to the wheels (except chrome wheels) to protect rims
from brake dust
Under Hood – Prior to Delivery
FF     Wipe down engine compartment and remove excess water from grille and hood area
Important: Do not use dressings or chemicals containing silicone!
Interior – Prior to Delivery
FF     Clean all glass/sunroof (if equipped/interior rear view mirror and visor mirrors)
FF     Remove all trim protection/coverings/stickers/decals
WARNING! Do not remove airbag warning triangle/warning labels
FF     Check upholstery/clean as required
FF     Check for excessive grease on seat tracks/clean as required
FF     Check all interior surfaces/compartments (including sun visors/headliner) for marks or
fingerprints. Clean as required
FF     Vacuum carpet
FF     Check luggage compartment and vacuum
FF     Install front/rear floor mats (including locking clip/tabs if applicable)/check that color matches
Final Detail Quality Inspection
FF     Re-inspect vehicle for surface scratches, swirl marks, paint chips, dents, wax residue, dust,
or lint, preferably in an area where vehicle is to be delivered. If this is not possible, inspect
vehicle in shop under fluorescent lights or in bright sunlight

11 of 12

PERFECT DELIVERY INSPECTION (PDI)

2013 A6/S6 | Inspection Verification

Client

VIN

Delivery Date

Audi Brand Specialist
I certify that all operations have been completed and this vehicle has been prepared in accordance
with Audi Procedures and Quality Standards.

Audi Brand Specialist Signature

Date

Porter
I certify that all operations have been completed and this vehicle has been prepared in accordance
with Audi Procedures and Quality Standards.

Porter Signature

Date

Technician
I certify that all operations have been completed and this vehicle has been prepared in accordance
with Audi Procedures and Quality Standards.

Technician Signature

Date

Detailer
I certify that all operations have been completed and this vehicle has been prepared in accordance
with Audi Procedures and Quality Standards.

Detailer Signature

Date

Would you like to schedule a Second Delivery?
FF     No

FF     Yes
Date

Time

By signing, I confirm all items in this checklist have been thoroughly reviewed with me and the statements below are true.
• Vehicle is clean and free of problems
• Received all keys and owner’s documentation
• Satisfied with features and controls explanations

Customer Signature

11-12-US

Date

12 of 12