7 ADJUSTING RV ENTRY DOOR CAMBER m
LiPPERT t
’ USING CAMBER ADJUSTMENT TOOL =
DOORS
Purpose
P Fig. 1
This document outlines the procedures to add camber to entry doors using
the RV Entry Door Camber Adjustment Tool PN 2023002404. The Camber
Adjustment Tool can be used to create positive camber. Usage of this tool can
provide proper sealing of the door and allow smooth open/close operation as
well as latch function. Top Leg
The Camber Adjustment Tool is available for purchase on the Lippert store:
https://www.lippert.com/rv-entry-door-camber-adjustment-tool-2023002404
Safety
Moving parts can pinch, crush or cut. Keep clear and use
caution.
This tool should NOT be used on Lippert G series doors that
have glass paneling. Using this tool on glass panel doors can
result in damage to the glass panel and cause possible injury to
the operator.
, Pressure y
Resources Required Adjustment
+ Camber adjustment tool PN 2023002404 (Fig. 1)
+ Level or straight edge that spans length of entry door
+ Tape measure
+ Adjustable wrenches to set standardized measurement
Entry Door Camber
Adjustment Tool
Rev: 03.12.2024 Page 1 €CD-0007331

7 ADJUSTING RV ENTRY DOOR CAMBER m
LiPPERT t
USING CAMBER ADJUSTMENT TOOL =
DOORS
This tool should NOT be used on Lippert G series doors that have glass paneling. Using this tool on
glass panel doors can result in damage to the glass panel and cause possible injury to the operator.
Procedures
1. Place straight edge against the inside of the door frame and measure the gap in the center of the door
frame between the straight edge and the inside of the door frame.
NOTE: The correct positive camber is a gap measuring between ¥" and 1%".
NOTE: A straight door edge has no camber, and positive and negative camber are measured from this
vertical surface (Fig. 2). Positive camber in an entry door is defined as a slight outward bow of the
door at the door latch. The purpose of the camber is to allow the door to contact the frame in the
top and bottom corners first, promoting a solid and weathertight seal when the door is latched.
Reverse or negative camber that allows the latch area of the door to contact first will result in
moisture entering the unit and causing water damage to the side walls and door frame areas.
aT: Ay
Positive Camber Negative Camber
2. If the gap is less than 1/8", use the camber adjustment tool to add positive camber.
A. Place the pressure adjustment handle and the threaded shaft of the camber rework tool as close as
possible to the bottom of the door latch on the inside of the door (Fig. 3).
NOTE: Make sure the pressure adjustment bumper is placed on the frame of the inner side of the door. If it is
placed on the inner plastic skin it may crush the foam and create a dent.
B. Place the top and bottom legs on the outside of the door frame (Fig. 3).
C. Slowly turn the tool handle clockwise until the tool creates additional camber on the entry door.
D. Periodically stop and check the measurement of the gap on the door until it reaches the optimal gap.
NOTE: Take care NOT to add excessive camber. Adding too much camber could crease the frame.
3. If there is extra positive camber on the door frame where the gap is larger than 1/4", use the camber
adjustment tool to reduce camber by putting the pressure adjustment bumper on the outside of the
door.
A. Place the pressure adjustment handle and the threaded shaft of the camber rework tool as close as
possible to the bottom of the door latch on the outside of the door.
B. Place the top and bottom legs on the inside of the door frame.
C. Slowly turn the tool handle clockwise until the tool removes camber on the entry door.
D. Periodically stop and check the measurement of the gap on the door until it reaches the optimal gap.
Rev: 03.12.2024 Page 2 CCD-0007331

we, ADJUSTING RV ENTRY DOOR CAMBER A
tiPPERT —_USING CAMBER ADJUSTMENT TOOL hi
DOORS
Fig.3
a j
\a §
Rev: 03.12.2024 Page 3 CCD-0007331

Y ADJUSTING RV ENTRY DOOR CAMBER m
LiPPERT t
USING CAMBER ADJUSTMENT TOOL z=
DOORS
Calibrate Tool To Preferred Measurement
The tool can be set so it provides a standardized measurement.
1. Set the first nut on the pressure adjustment shaft at the preferred stop point (Fig. 4).
2. Place the second nut directly behind the first nut (Fig. 5).
3. With two adjustable wrenches, hold first nut in place and tighten second nut against the first nut to
lock it in place.
iat: Ae Fig. 5
PS ) b Um
Al )
Set First Nut Move Second Nut,
| | Tl - §
Video Illustrating Tool Use
To access a video, demonstrating the camber adjustment tool, use the following link:
https://support.|ci1.com/videos/how-to-use-a-lippert-entry-door-camber-adjustment-tool
Users can also utilize the following QR code to access the video. A copy of the QR code is also included on
the entry door camber tool.
laste el
ath
eich
Pe ii
Fe eanh
ese
Asa supplier of a broad array of highly-engineered components in the recreation and transportation product markets, safety, education and customer satisfaction are
our primary concerns. Should you have any questions, please do not hesitate to contact us at 432-LIPPERT (432-547-7378) or by email at [email protected].
Self-help tips, technical documents, product videos and a training class schedule are available at lippert.com or by downloading the LippertNOW app.