Loading...

NHTSA ID Number: 10251050

Manufacturer Communication Number: Owners documenta

TSB/Document Date: 2024-03-04


Summary

TeslaeBay logo does not provide physical owner's manual copies. Instead, all available owner?s manual content is integrated into the vehicle software, and only the content relevant for a given vehicle, based on vehicle configuration and software version installed, is displayed on its touchscreen. This file contains all available owner?s manual content for 2021-2023 Model X vehicles converted to PDF format, and given the distribution method and NHTSA?s submission format requirements, it is the best available representative copy of owner?s manual content. However, a customer who accesses the owner?s manual via their vehicle?s touchscreen would only see the parts of this PDF file that are relevant to their vehicle.


Maintenance on page 254). Proper tire pressures help protect tires from potholes and improve range when properly
inflated.
While Driving
Cold weather can increase energy consumption because more power is required for driving, cabin and Battery
heating. Follow these suggestions to reduce energy consumption:
• Use seat heaters to keep warm. Seat heaters use less energy than the cabin heater. Lowering the cabin
temperature and using seat heaters reduces energy consumption (see Operating Climate Controls on page 211).
• Slow down your driving and avoid frequent and rapid acceleration.

220

Owners Manual
• You can improve the efficiency of the cabin heating by reducing your selected acceleration mode (see
Acceleration Modes on page 133). This allows the heat pump system to take more heat from the Battery to
efficiently heat the cabin, instead of maintaining the Battery's ability to provide peak acceleration performance.
This helps to maximize driving efficiency in colder weather. Note that when subsequently increasing the
acceleration mode, the Battery requires time to warm up before the increased level of acceleration is available.
Regenerative Braking

Regenerative braking can be limited if the Battery is too cold. As you continue to drive, the Battery warms up and
regenerative power increases (see Regenerative Braking on page 124).
NOTE: Limited regenerative braking can be avoided if you allow enough time to precondition your vehicle or if you
use Schedule to precondition Model Y before your departure time (see Scheduled Charging and Scheduled
Departure on page 246).
NOTE: Installing winter tires can result in temporarily reduced regenerative braking power but after a short period of
driving, Model Y recalibrates to correct this. Touch Service > Wheel & Tire > Tires to select winter tires and quicken
this process.
Cold Battery

A blue snowflake icon appears on your touchscreen when some of the stored energy in the Battery is
unavailable because the Battery is cold. This portion of unavailable energy displays in blue on the Battery
meter. Regenerative braking, acceleration, and charging rates may be limited. The snowflake icon no longer
displays when the Battery is sufficiently warm.
After Driving
Leave Model Y plugged in when not in use. This uses the charging system, rather than the Battery itself, to keep the
Battery warm (see High Voltage BatteryeBay logo Information on page 238).
Scheduled Departure

When parked, plug in Model Y and use the Schedule settings, available on both the charging and climate control
screens, to set a time when you want to precondition Model Y (see Scheduled Charging and Scheduled Departure on
page 246). Your vehicle determines the appropriate time to begin charging so it is complete during off-peak hours
and the cabin and Battery are warm by your set departure time.
Storage
If you leave Model Y parked for an extended period of time, plug the vehicle into a charger to prevent normal range
loss and to keep the Battery at an optimal temperature. Your vehicle is safe to stay plugged in for any length of time.
When not in use, Model Y enters a sleep mode to conserve energy. Reduce the number of times you check your
vehicle’s status on the mobile app, as this automatically wakes up your vehicle and starts normal energy
consumption.

221

Owners Manual
Hot Weather Best Practices
To ensure that Model Y provides you with the best ownership experience possible in hot ambient conditions, follow
these best practices.
Before Driving
There are several ways to prepare your vehicle for a drive, without having to get into an already hot vehicle:
• Touch Schedule, available on both the Charging and Climate Control screens, to set a time when you want your
vehicle to be ready to drive (see Scheduled Charging and Scheduled Departure on page 246).
• Precondition the cabin by moving the direction of air flow from the vents, and turn the seat heaters on or off. In
the mobile app, navigate to Climate to customize the temperature at which you want to heat the cabin.
• In the mobile app, navigate to Controls to vent the windows.
NOTE: TeslaeBay logo recommends activating climate settings at least 30-45 minutes before departure (see Operating
Climate Controls on page 211). Preconditioning times depend on outside temperature and other factors. The
mobile app will notify you once your vehicle has reached the desired preconditioning temperature.
• Enable Cabin Overheat Protection, which prevents the cabin from getting too warm in hot ambient conditions.
You can choose whether you want the A/C or just the fan to run when the temperature in the cabin exceeds 105°
F (40° C) or the selected temperature (if available).
After Driving
Leave Model Y plugged in when not in use, especially if using Preconditioning or Cabin Overheat Protection. This
uses the charging system, rather than the battery itself, to maintain a comfortable temperature (see High Voltage
Battery Information on page 238). In addition, there are several ways to minimize a hot cabin:
• Before leaving your vehicle, use Dog Mode to keep the cabin cool for pets or perishable goods. See Keep Climate
On, Dog, and Camp on page 213 for more information.
TeslaeBay logo recommends turning the air conditioning off approximately 30 seconds before pressing Park to reduce
puddling below the vehicle.
• Park in the shade to help reduce power consumption and maintain cooler cabin temperatures.
• Use a sun shade (available on the TeslaeBay logo Shop) if you have to park outside in the sun.
• When parked, plug in Model Y and Schedule your charging. Your vehicle determines the appropriate time to
begin charging so it is complete during off-peak hours. The cabin and Battery are also prepared by your set
departure time. For more information, see Scheduled Charging and Scheduled Departure on page 246.
Charging
When using Trip Planner or navigating to a Supercharger station, your vehicle automatically prepares the Battery for
most efficient charging. In extreme heat, you may not see the message that the vehicle is preconditioning the
Battery while navigating to a Supercharger, but it is still preparing the Battery for charging.
NOTE: TeslaeBay logo recommends using Trip Planner to navigate to a charging location for at least 30-45 minutes before
arrival to ensure optimal Battery temperature and charging conditions. If the drive to the charging location is less
than 30-45 minutes, consider preconditioning the Battery before driving (see Before Driving on page 218).
If possible, leave your vehicle plugged into a charger whenever not in use, even in warm weather, especially if using
preconditioning or Cabin Overheat Protection.
Storage
If you leave Model Y parked for an extended period of time, plug the vehicle into a charger to prevent normal range
loss and to keep the Battery at an optimal temperature. Your vehicle is safe to stay plugged in for any length of time.
When not in use, Model Y enters a sleep mode to conserve energy. Reduce the number of times you check your
vehicle’s status on the mobile app, as this automatically wakes up your vehicle and starts normal energy
consumption.

222

Owners Manual
Navigation and Entertainment
Maps and Navigation
Map Overview
The touchscreen displays a map at all times (except when Model Y is shifted into Reverse).
Use your finger(s) to interact with the map:
• To move the map in any direction, hold and drag a finger.
• To rotate the map in any direction, hold and turn two fingers.
• To zoom the map in or out, expand or pinch two fingers, respectively.
NOTE: When you rotate or move the map, your current location is no longer tracked. The message "Tracking
Disabled" displays briefly next to the map orientation icon and the icon turns gray. To re-enable tracking, touch the
map's orientation icon and choose North Up or Heading Up.
NOTE: The map zooms in and out automatically when a navigation route is active.
To change the orientation of the map, toggle between these options:
North Up: North is always at the top of the screen.

Heading Up: The direction you are driving is always at the top of the screen. The map rotates as you
change direction. This icon has an integrated compass that indicates the direction you are driving.
NOTE: Touching this icon while navigating to a destination displays the route overview.

Route overview is available when you are navigating to a destination and displays when you expand
the turn-by-turn direction list (by swiping it downward). When you collapse the turn-by-turn direction
list by swiping it upward, the map displays your previously chosen orientation.

Map Display
When Model Y is in Park, the following icons display on the map to allow you to customize the type of information
the map displays. To access these icons when driving, touch anywhere on the map (they disappear after a few
seconds).
Satellite imagery (if equipped with premium connectivity).

Traffic conditions (if equipped with premium connectivity).

223

Owners Manual
Map details (such as points of interest).

Drop a pin anywhere on the map by pressing and holding your finger on a desired location. When you drop a pin, or
touch an existing pin, the chosen location is centered on the map and a popup screen provides information about
the location. From this popup, you can navigate to the location add or remove the location from your list of favorite
destinations (see Home, Work, and Favorite Destinations on page 226).

Charging locations. Shows a popup list that includes the city and proximity of the corresponding
stations on the map. Charging locations include Tesla Superchargers, destination charging sites, thirdparty fast chargers, and public chargers that you have used previously. See Charging Locations on
page 227. Touch the lightning bolt icons in the popup list to filter by the types of chargers based on
max power.
NOTE: In some market regions, third-party fast chargers are also included on the map as dark gray pins
when you display chargers.
Navigation Settings
NOTE: The navigation settings available can vary depending on region and vehicle configuration.
The navigation settings icon displays when you touch ... once you start navigating to a destination.
NOTE: You can also access navigation settings by touching Controls > Navigation.

Touch the navigation settings icon to customize the navigation system to suit your preferences (the available
settings vary depending on your market region and vehicle configuration):
• Navigation Guidance: Touch Voice to enable an audible reading for navigation instructions.
• Touch - or + to increase or decrease the volume of spoken navigation instructions. Decreasing all the way to the
left or touching the speaker icon mutes the instructions. You can also mute/unmute navigation instructions by
touching the speaker icon. This volume setting applies only to the navigation system's spoken instructions.
Volume for Media Player and Phone does not change.
NOTE: Volume may automatically be adjusted based on driving speed and climate settings.
• Enable Automatic Navigation if you want Model Y to automatically initiate a navigation destination when you get
in your vehicle. Destinations are predicted based on commonly driven routes, time of day, and calendar entries
(see Automatic Navigation on page 226).
• Enable Trip Planner (if available in your market region) to add Supercharger stops as needed. Supercharging
stops are added to navigation routes with the goal of minimizing the amount of time you spend driving and
charging (see Trip Planner on page 229).
• Enable Online Routing to automatically route to avoid heavy traffic and to get real-time traffic conditions along
navigation routes, if available in your region (see Online Routing on page 228).
• Touch Avoid Ferries to be automatically routed to avoid ferries.
• Touch Avoid Tolls to be automatically routed to avoid tolls, if possible.
• Touch Use HOV Lanes to include High Occupancy Vehicle (HOV) lanes on navigation routes. This is particularly
useful when using Navigate on Autopilot (see Navigate on Autopilot on page 158).
Navigating to a Destination
To navigate to a location, touch the search bar in the corner of the map and enter a destination, send the destination
from your phone, or use voice commands (see Voice Commands on page 22) for an address, landmark, business, etc.
When you touch the search bar, you can also choose from the following types of locations:
224

Owners Manual
• A saved Home or Work location (see Home, Work, and Favorite Destinations on page 226).
• A Charging destination (see Charging Locations on page 227).
• A Recent destination (the most recent destination is listed at the top).
• A destination you have marked as a Favorite (see Home, Work, and Favorite Destinations on page 226).
• A popular restaurant when you're feeling Hungry or a popular destination (such as museums and amusement
parks) when you're feeling Lucky (see Lucky and Hungry on page 226).
NOTE: You can start navigation remotely from your IOS® or Android™ device using the "share" functionality on your
device after allowing access to the Tesla mobile app.
When you specify a location, the touchscreen zooms out to provide an overview of the route you need to travel and
displays a turn-by-turn direction list. Estimated arrival time, driving time, and mileage displays at the bottom of the
direction list. Note the following about the turn-by-turn direction list:
• The Battery icon on the turn list provides a visual representation showing an estimate of how much energy will
remain when you reach your destination, and how much will remain if you make a round trip back to your current
location. See Predicting Energy Usage on page 228.
• If charging is needed to reach your destination and Trip Planner is enabled (and available in your market region),
the navigation route automatically includes Supercharger stops (see Trip Planner on page 229).
• If you won't have enough energy to reach your destination and there is no Supercharger on the route, an alert
tells you that charging is needed to reach your destination.
• Each turn is preceded by the distance to the maneuver.
• To see the bottom of the list, you may need to drag the list upward.
• Touch the top of the list to minimize it.
While navigating, the map tracks your location and displays the current leg of your trip. You can display the entire
route at any time by swiping down to expand the turn-by-turn direction list or touching the route overview icon.
To stop navigating, touch Cancel, located in the bottom corner of the turn-by-turn direction list.
NOTE: If a data connection is not available, onboard maps allow you to navigate to any destination, but you must
enter the exact and complete address.
If Navigate on Autopilot is enabled, you can turn it on for the navigation route by touching Navigate
on Autopilot in the turn-by-turn direction list (when the feature is active, the icon is blue). Navigate on
Autopilot is a full self-driving (Beta) feature that automatically changes lanes and steers Model Y on
controlled-access roads (like highways and freeways), along a navigation route. For details, see
Navigate on Autopilot on page 158.
Selecting an Alternate Route

Depending on market region and vehicle configuration, this feature may not be available on your vehicle. Your vehicle
must be equipped with Premium Connectivity.
After you have entered a destination with one stop, the map displays up to three alternate routes. This allows you to
easily compare total travel time and traffic information for each route. If you do not select a preferred route within
the timeout period, the fastest route is automatically selected.
Adding Stops to a Route

After entering a destination, edit your route by adding, deleting or reordering stops. Touch the three dots at the
bottom of the turn-by-turn direction list to view options to edit your route.
Add Stop allows you to add a stop by searching for a location or adding a Home, Recent or Favorite
destination. You can also add a stop by touching any pin on the map and selecting Add from the
popup.

225

Owners Manual
Edit Stop allows you to set up a complex trip by adding or deleting stops on your route. Drag and drop
stops by touching the equal sign to reorder your trip.

You can also use the Tesla mobile app to edit your route (if available in your region). In the Tesla mobile app, go to
Locations > Navigate and enter a destination, touch Edit Trip > Add Stop to edit your route, then touch Send to Car
to share the trip with your vehicle.
NOTE: Requires Tesla mobile app version 4.27.5 or newer.
Automatic Navigation

NOTE: Automatic Navigation may not be available in all market regions and on all vehicle configurations.
Automatic Navigation can predict a destination when you get in your vehicle. When your phone's calendar is synced
to Model Y, and the calendar includes an event that takes place within two hours of when you get in your vehicle to
drive, Automatic Navigation suggests the location of the event (assuming a valid address is associated with the
event).
In addition, if you are Home and drive on weekdays (Monday to Friday) from 5:00 AM to 11:00 AM, Automatic
Navigation can automatically route you to your specified Work location (see Home, Work, and Favorite Destinations
on page 226). Likewise, if you are at work on weekdays from 3:00 PM to 11:00 PM, Automatic Navigation can
automatically route you to your specified Home location.
To enable Automatic Navigation, touch Controls > Navigation > Automatic Navigation. You must have your phone's
calendar synced to Model Y and the event must include a uniquely specified and valid address (see Phone, Calendar,
and Web Conferencing on page 101).
NOTE: Navigation instructions that you enter manually, or send to Model Y, override routes suggested by Automatic
Navigation.
Lucky and Hungry
NOTE: "Lucky" and "Hungry" may not be available in all market regions and on all vehicle configurations.
In addition to navigating to a destination of your choice, Model Y can also suggest nearby locations based on
whether you are feeling Hungry or Lucky. In the navigation search bar, touch Hungry or Lucky. Hungry suggests a
list of popular restaurants, whereas Lucky suggests a list of popular destinations (such as museums and amusement
parks). Once you discover an interesting destination, touch Navigate to proceed to the destination.
This feature requires the latest version of Navigation maps. To download, connect Model Y to Wi-Fi and touch
Controls > Software to check if an update is available (see Map Updates on page 229).
Home, Work, and Favorite Destinations
If you frequently drive to a destination, add it as a favorite to avoid entering the location's name or address each
time. When you add a destination as a Favorite, you can easily navigate to it by touching the navigation search bar
and then touching Favorites and choosing it from your list of favorite destinations.
To add a destination to your Favorites list touch its pin on the map, then touch the star icon on the
popup screen that appears. Enter a name (or leave as-is to accept the default name), then touch Add
to Favorites. The star becomes solid and the destination is included on your Favorites list.

To delete a Recent or Favorite destination, touch it on the destination list and hold it down briefly until the X
appears. Then touch the X to delete it from the list.
Home and Work locations also display under the navigation search bar. Touch to set an address to the
corresponding location. After entering the address, touch Save as Home or Save as Work. Then simply touch these
shortcuts whenever you want to navigate home or to work.

226

Owners Manual
To change or delete the corresponding address, press and hold the Home or Work icon. A popup allows you to enter
a new address and Save as Home or Save as Work. Once a Home or Work location is saved, Model Y may prompt
you to navigate to your Work location in the mornings and to your Home location in the evenings and provide an
estimated driving time based on current traffic conditions. See Automatic Navigation on page 226. Touch Clear
Home or Clear Work to remove associated addresses entirely. Based on your usage patterns, Model Y may prompt
you to save a location as Home or Work.
For security reasons, if you sell Model Y, it is recommended that you delete your Home and Work locations. You can
delete these individually or you can perform a factory reset to erase all personal data (touch Controls > Service >
Factory Reset).
Charging Locations
To display charging locations on the map, touch the map's search bar, then touch Charging. Charging locations are
shown in a list (with the closest charging location at the top of the list) and represented by corresponding pins on
the map. Touch a pin to display more information, navigate to it, or mark it as a favorite.
Touch the lightning bolt icons to specify the types of charging locations you want the map to include (by default, the
map displays only Superchargers):
Touch to include low power stations up to 70 kW, such as destination charging locations.

Touch to include high power chargers above 70 kW.

NOTE: In some market regions, third-party fast chargers are also included as dark gray pins when you choose to
display all charging stations.
The appearance of a charging location's pin reveals the predicted status about the location. Touch the pin to display
details.
The Supercharger location is operational and the number displayed on the pin represents the predicted
number of available Supercharger stalls upon arrival.
NOTE: A Supercharger located on your current navigation route is colored black (or white, if the
touchscreen is in night mode).
The Supercharger location is predicting a high volume of users. You may need to wait before charging.

The Supercharger location may be operating at a reduced capacity.

The Supercharger location may be closed.

227

Owners Manual
The Supercharger location has no data available but should be operational.

The location is either a destination charging location, a third-party fast charger, or a public charging
station that you have previously used. Touch to display more information such as usage restrictions and
available charge current.
NOTE: When the map is zoomed out and more than one destination charging location is available in an
area, the pin is round and displays the number of stations. Touch the pin to zoom in. Then you can
touch an individual pin for details about a specific location.
Touch a charging location's pin to display a popup from which you can:
• Determine it's exact location and approximate distance from your current location.
• View amenities that are available at the charging location, including restrooms, restaurants, lodging, shopping,
and Wi-Fi. On a Supercharger popup, touch an amenity icon to search the surrounding area for the associated
amenity.
• Touch the arrow icon to navigate to the charging location.
NOTE: When navigating to a Supercharger (or third-party fast charger in some regions), Model Y preconditions
the Battery to prepare for charging. This ensures you arrive with an optimal Battery temperature, reducing the
amount of time it takes to charge. In some circumstances (such as cold weather), it is normal for the motor(s) and
components to make noise as it generates heat to warm the Battery (see Charging on page 218).
• View how busy a Supercharger location typically is during different times of the day, along with corresponding
charging fees and idle fees (see Supercharger Fees on page 244).
Predicting Energy Usage
When navigating to a destination, Model Y helps you anticipate your charging needs by calculating the amount of
energy that remains when you reach your destination. When navigating, the map displays this calculation next to the
Battery icon on the turn-by-turn direction list (see Navigating to a Destination on page 224). When the turn-by-turn
direction list is compressed, touch the top of the list to expand it.
The calculation that predicts how much energy you will use is an estimate based on driving style (predicted speed,
etc.) and environmental factors (elevation changes, wind speed and direction, ambient and forecasted temperatures,
air density and humidity, etc.). As you drive, Model Y continuously learns how much energy it uses, improving
accuracy over time. Model Y predicts energy usage based on the driving style of the individual vehicle. For example,
if you drive aggressively for a period of time, future range predictions will assume higher consumption. Also, if you
purchase a used Tesla vehicle, it is recommended that you perform a factory reset (Controls > Service > Factory
Reset) to ensure the predicted energy is as accurate as possible. Some factors that contribute to predicted energy
(such as forecasted temperatures and wind speed) are available only when Model Y has internet connectivity.
Throughout your route, Model Y monitors energy usage and updates the estimate of energy remaining at the end of
your trip. A popup warning displays on the turn-by-turn direction list in these situations:
• A yellow warning displays when you have very little energy remaining to reach your destination, requiring you to
drive slowly to conserve energy. For tips on conserving energy, see Getting Maximum Range on page 247.
• A red warning displays when you must charge to reach your destination.
To determine if you have enough energy for a round trip, touch the Battery icon on the turn-by-turn direction list to
display an estimated calculation of your round trip energy usage.
Online Routing
Model Y detects real-time traffic conditions and automatically adjusts the estimated driving and arrival times. In
situations where traffic conditions will delay your estimated time of arrival and an alternate route is available, the
navigation system can reroute you to your destination. You can also specify the minimum number of minutes that
must be saved before you are rerouted. To turn this feature on or off, touch Controls > Navigation > Online Routing.

228

Owners Manual
When Online Routing is enabled, real-time traffic condition icons display along navigation routes when detected, if
available in your region (Premium Connectivity required).
Appears when a speed camera is detected.

Trip Planner
Trip Planner (if available in your region) helps you take longer road trips with confidence. If reaching your destination
requires charging, Trip Planner routes you through the appropriate Supercharger locations. Trip Planner selects a
route and provides charging times to minimize the amount of time you spend driving and charging. To enable Trip
Planner, touch the map's settings icon (see Navigation Settings on page 224), then touch Trip Planner.
When Trip Planner is enabled and charging is required to reach your destination, the turn-by-turn direction list
includes Supercharger stops, recommended charging times at each Supercharger, and an estimate of how much
energy will be available when you arrive at the Supercharger location.
To remove Supercharger stops and display directions only, touch Remove all charging stops at the bottom of the
turn-by-turn direction list. If you remove charging stops, the turn-by-turn direction list may display an alert indicating
that charging is needed to reach your destination. To add Supercharger stops back to the turn-by-turn direction list,
touch Add charging stops.
While charging at a Supercharger, the charging screen displays the remaining charging time needed to drive to your
next Supercharger stop or destination (if no further charging is needed). If you charge for a shorter or longer length
of time, charging time at subsequent Supercharger stops is adjusted accordingly. You can also use the mobile app to
monitor remaining charging time needed.
NOTE: When navigating to a Supercharger or, in some regions, a third-party fast charger using Trip Planner, Model Y
may allocate some energy to pre-heat the Battery to arrive at the Supercharger or third-party fast charger with an
optimal Battery temperature. This reduces charging time (see Charging on page 218).
If Trip Planner estimates that you won't have enough energy for your round trip, and there are no Superchargers
available on your route, Trip Planner displays an alert at the top of the turn-by-turn direction list notifying you that
charging is needed to reach your destination.
NOTE: If a Supercharger on your navigation route experiences an outage, Trip Planner displays a notification and
attempts to reroute you to a different Supercharger location.
Map Updates
As updated maps become available, they are automatically sent to Model Y over Wi-Fi. To ensure you receive them,
periodically connect Model Y to a Wi-Fi network (see Wi-Fi on page 97). The touchscreen displays a message
informing you when new maps are installed.

229

Owners Manual
Media
Overview
NOTE: Media apps vary depending on market region, vehicle configuration, options purchased, and software version.
Some apps described may not be available in your market region, or may be replaced by different ones.
The Media Player displays in the cards area or on the touchscreen and is used to play various types of media. You
can drag Media Player upward to expand it (allowing you to browse), and downward to minimize it so that just the
Miniplayer displays. The convenient Miniplayer, which occupies the least amount of space on the touchscreen,
displays what's currently playing and provides only the basic functions associated with what's playing.
Streaming services are available only when a data connection is available (for example, Wi-Fi or Premium
Connectivity). For some media services, you can use a default Tesla account. For others, you may need to enter
account credentials the first time you use it.
Media Player displays content and options associated with the app (or source) you choose from the app launcher, or
from the dropdown list that displays on the Media Player when you expand it:
Radio: Choose from a list of available radio stations or touch the numeric keypad to directly tune the
radio to a specific frequency. Touch the next or previous arrows to move from one frequency to the
next (or previous).

Bluetooth: Play audio from a bluetooth-connected phone or USB device (see Playing Media from
Devices on page 232).

Streaming: Play the audio streaming service available in your market region (for example, Slacker
Radio), if equipped.

Spotify: Play audio available on Spotify.
NOTE: A Spotify Premium account is required for use.

Apple Music: Play audio available on Apple Music.

Caraoke (if equipped): Sing along with various songs (see Caraoke on page 232).

TuneIn: Play audio available on TuneIn.

230

Owners Manual
Tidal: Play audio available on Tidal.

NOTE: You can show or hide any media app/source. See Media Settings on page 231.
When listening to internet radio or a music streaming service, the options available on the Media Player screen vary
depending on what you are listening to. Touch the next (or previous) arrows to play the next (and in some cases
previous) available station, episode, or track. You can also play next/previous using the left scroll button on the
steering wheel.
NOTE: Instead of launching a different media app, you can change the source from within the Media Player screen by
choosing a source from the dropdown list.
NOTE: You can use voice commands to adjust media settings and preferences, such as volume control, playing
certain songs, or switching the media source (see Voice Commands on page 22).
Volume Controls
Volume can be controlled by:
• Roll the scroll button on the left side of the steering wheel up or down to increase or decrease volume
respectively.This adjusts the volume for media, voice commands, and phone calls.
• Volume may be adjusted based on your driving speed and climate settings.
• Touch the arrows associated with the speaker icon on the bottom corner of the touchscreen.
• To mute the volume, press the left scroll button. Press again to unmute.
• Pressing the left scroll button during a phone call mutes both the sound and your microphone.
Media Settings
NOTE: The settings available vary depending on market region. Also, a setting may not be applicable to all audio
sources.
When displaying an audio source screen, press the settings icon located in the search bar to access
audio settings.

You can adjust these settings:
• Tone: Drag the sliders to adjust the subwoofer and any of the five frequency bands (Bass, Bass/Mid, Mid, Mid/
Treble, and Treble). If equipped with premium audio, you can adjust the level of sound immersion to make your
music experience more engaging by dragging the immersive sound slider according to your preferences.
• Balance: Drag the center circle to the location in Model Y where you want to focus the sound.
• Options: Set preferences for optional features. For example, you can turn DJ Commentary, Explicit Content and
Allow Mobile Control on or off.
• Sources: Displays all available media sources and allows you to choose whether you want to show or hide each
source. You may want to hide media sources that you never use. Once hidden, the media source does not appear
on the drop down list in Media Player, nor will it appear in the app tray when you touch the App Launcher. You
can re-display a hidden media source at any time by returning to this settings screen.

231

Owners Manual
Searching Audio Content
Touch Media Player's magnifying glass icon to search for a particular song, album, artist, podcast, or
station. You can also use voice commands to search hands-free (see Voice Commands on page 22). If
available, touch HD® to play high definition versions of the selected frequency.

Caraoke
NOTE: Depending on vehicle configuration and market region, Caraoke may not be available on your vehicle.
In addition to various streaming services, your vehicle may be equipped with Caraoke. Navigate to Media Player and
select the drop down menu to change the media source to Caraoke. Or add Caraoke as an app in the app launcher.
You can browse through various songs and select the song you want to sing. Touch the microphone icon to enable
or disable the song's main vocals. Disabling the microphone leaves only the song's instrumentals and background
vocals. Touch the lyrics icon (located next to the microphone icon) to enable or disable the song's lyrics.
WARNING: Never read Caraoke lyrics while driving. You must always pay attention to the road and traffic
conditions. When driving, the Caraoke lyrics are intended only for use by a passenger.
Recents and Favorites
For most source content, recents and favorites display at the top for easy access.
To add a currently playing station, podcast, or audio file to your Favorites list, touch the Favorites icon
on Media Player.

To remove an item as a favorite, touch the highlighted Favorites icon. You can also remove multiple
favorites by expanding Media Player to show all favorites for the applicable type of source content.
Then press and hold any favorite. An X appears on all favorites and you can then touch the X to remove
them from your Favorites list.
Your recently played selections are updated continuously so you don't need to remove them.

NOTE: Selections you play on FM (if equipped) radio are not included in the Recents list.
Playing Media from Devices
USB Connected Flash Drives

Insert a flash drive into a front USB port (see USB Ports on page 10). Touch Media Player > USB, then touch the
name of the desired folder.
NOTE: To play media from a USB connection, Model Y recognizes flash drives only. To play media from other types
of devices (such as an iPod), you must connect the device using Bluetooth (see Bluetooth Connected Devices on
page 233).
NOTE: Media Player supports USB flash drives with exFAT formatting (NTFS is not currently supported).
NOTE: Use a USB port located at the front of the center console. The USB connections at the rear of the console are
for charging only.
NOTE: For some vehicles manufactured after approximately November 1, 2021, the center console USB ports may
only support charging devices. Use the USB port inside the glove box for all other functions.

232

Owners Manual
Bluetooth Connected Devices

Pair your Bluetooth-capable device to Model Y (see Bluetooth on page 98) to play stored audio files. Choose Media
Player's Phone source, touch the name of your Bluetooth-connected device, then touch CONNECT.

233

Owners Manual
Theater, Arcade, and Toybox
Overview
NOTE: Entertainment options may vary depending on market region, date of manufacture, and vehicle configuration.
The touchscreen displays the Entertainment screen when you choose any of the following apps:
Theater: Play various video streaming services (such as Netflix, YouTube, Hulu, etc.) while parked.
Available only if Model Y is connected to WiFi, or is equipped with premium connectivity and a cellular
signal is available.

Arcade: Want to game? You may need to use the steering wheel buttons or a Bluetooth or USB
controller to play. See Gaming Controllers on page 236.
NOTE: For some vehicles manufactured after approximately November 1, 2021, the center console USB
ports can only be used to charge devices. On these vehicles, you must use the USB port inside the
glove box.
Toybox: Play in the Toybox while parked.

WARNING: Use these features only when Model Y is parked. Always pay attention to road and traffic
conditions when driving. Using these features while driving is illegal and very dangerous.
NOTE: You can also use voice commands to access these features (see Voice Commands on page 22).
Toybox
Your vehicle's toybox includes features that can be fun to use. Here's an example of the types of features you can
find in Toybox:
Select This...

To Do This...

Boombox

If Model Y is equipped with a Pedestrian Warning System, delight pedestrians with a variety of
sounds from your vehicle's external speaker while in Park. See Boombox on page 235 for more
details.
NOTE: Check local laws before using Boombox in public areas.

Emissions

Fun can come in surprising ways. Select your preferred fart style and target seat. Use your turn
signal or press the left scroll wheel when you’re ready to “release” your prank. For those lucky
vehicles equipped with a Pedestrian Warning System, you can choose to broadcast externally
when your vehicle is parked. But wait-- the fun doesn't stop there! Use the mobile app to
conduct remote emissions testing by touching and holding any of the four quick control buttons
and selecting the fart button.

Light Show

Park outside, turn the volume up, roll down your windows, then enjoy the show. Schedule the
light show for a future time and customize the song to surprise your loved ones.
NOTE: Light show should not be used when parked on or near public roads. Doing so can be
distracting to other road users. Before activating, it is the driver’s responsibility to ensure the use
of light show complies with local laws and regulations.
NOTE: Light show supports multiple custom shows from one USB drive to enjoy and share with
others (follow the instructions onscreen).

Mars

The map shows your Model Y as a rover on the Martian landscape, and the About Your Tesla box
displays SpaceX's interplanetary spaceship.

234

Owners Manual
Rainbow
Charge Port

When Model Y is locked and charging, press the button on the mobile connector ten times in
quick succession. Neat, huh?

Rainbow Road

Need more cowbell? Visit Rainbow Road by moving the drive stalk fully down four times in quick
succession while Autosteer is enabled.

Romance

You can’t roast chestnuts by an open fire in your car, but you can still cozy up with your loved
ones by this virtual fireplace. Cue the music and get your romance on!

Sketchpad

1...1112131415...26

SaleBestseller No. 1
TOPDON RLink J2534 Pass-Thru Programmer, OEM Reprogramming and Diagnostic Tool, Enhanced J2534 VCI, Supports J2534/D-PDU/CAN-FD/DoIP, Compatible with 18+ Vehicle Brands, No OE Software Provided
289 Reviews
TOPDON RLink J2534 Pass-Thru Programmer, OEM Reprogramming and Diagnostic Tool, Enhanced J2534 VCI, Supports J2534/D-PDU/CAN-FD/DoIP, Compatible with 18+ Vehicle Brands, No OE Software Provided
  • J2534 Pass-Thru Programmer: TOPDON RLink J2534 is an...
  • All-in-One OEM Diagnostics: This J2534 ECU programming tool...
  • Proven Performance You Can Trust: Backed by over 10000 real...
  • Integrated Excellence, Always Up-to-Date: Featuring the...
  • Efficiency Meets Versatility: Engineered to support three...
SaleBestseller No. 2
TOPDON RLink J2534 Reprogramming Tool, High-Speed J2534 Pass-Thru Programmer, OEM Reprogramming and Diagnostic Tool, Supports J2534/D-PDU/CAN-FD/DoIP, 17+ Vehicle Brands Supported
  • Advanced VCI Box, Industry-leading J2534 Pass-Thru...
  • High-Speed OEM-Level Diagnostics & Programming: Unlock true...
  • Coverage for 17 Car Brands & Ultra Reliability: Works...
  • User-Friendly RLink Platform & Expert Support: TOPDON’s...
  • 6.6 ft USB-C Cable & Portable Storage Case: The RLink J...

If the PDF is very large, it may not load in the preview below.

Download PDF [10.94 MB]


Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.

If the TSB PDF does not show, download or view it on the NHTSA Website.

Click on the (+) Plus Sign

Then Click on Associated Document(s)


Search NHTSA Database for Recalls

View Latest Recalls


Search NHTSA Database for Vehicle Investigations

View Latest Vehicle Investigations


Search NHTSA Database for Vehicle Complaints

View Latest Vehicle Complaints


TSB/Document ID: Owners documenta

Replacement Service Bulletin Number:

MFR Communication Date: 2024-01-18

MFR Internal Campaign ID/Software Version:

Communication Type: Service Bulletin/Repair Instructions

NHTSA Components: EQUIPMENT

MFR Component System:

MFR Component Subsystem:


Previous TSB

Next TSB



Sale
THINKCAR Bidirectional OBD2 Scanner Diagnostic Tool 689BT - All System Scan Tool with Bluetooth 5.0, 3000+ Active Tests,ECU Coding, 34+ Services, FCA, CAN-FD and DoIP, Wireless Update
108 Reviews
THINKCAR Bidirectional OBD2 Scanner Diagnostic Tool 689BT - All System Scan Tool with Bluetooth 5.0, 3000+ Active Tests,ECU Coding, 34+ Services, FCA, CAN-FD and DoIP, Wireless Update
  • [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
  • Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
  • Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
  • 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
  • Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
Sale
XTOOL D7S Bidirectional Scan Tool, 2026 AI-Assisted OBD2 Scanner Diagnostic Tool with FCA AutoAuth, All System Car Scanner, 39+ Resets, ECU C0ding, PMI, Upgrade of D7, Crankshaft Relearn, CAN FD/DoIP
  • Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCAeBay logo Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations
  • 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCAeBay logo AutoAuth: Now supports FCAeBay logo SGW module for ChryslereBay logo, for JeepeBay logo, for DodgeeBay logo (2018+), for FiateBay logo (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for FordeBay logo, for LincolneBay logo, and for MazdaeBay logo ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
  • 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
  • Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMWeBay logo, for Benz and offline for BENZ, for MIT, along with PMI functions for FordeBay logo, for MazdaeBay logo, and for LincolneBay logo. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
  • OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
Sale
2026 BOSSCOMM IF745 Scanner Diagnostic Tool, Check Engine Code Reader with 6 Resets, ABS Bleeder/Oil/EPB/SAS/Throttle/Battery, Scanner Diagnostic Tool for Vehicles, Lifetime Free Update, Auto VIN
  • 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
  • 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
  • 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
  • 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.​
  • 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.

This product presentation was made with AAWP plugin.

Share to...