T-SB-0098-23

December 6, 2023

2024 86 Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2024

86

ADDITIONAL INFORMATION

Introduction

Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer
feedback indicates the following areas deserve special attention when performing PDS:





Careful inspection for paint chips/scratches and body dents/dings.
Proper operation of electrical accessories (including interior light, clock, and radio reset).
Interior cleanliness.
Proper function of mechanical systems.

Customer retention and proper maintenance of vehicles are and have always been a major focus
for Toyota. To help remind customers that regular service is essential to the proper maintenance
of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing
this, customers will be reminded to return to your dealership for service. Your current service
reminder sticker may be used. (See PDS Check Sheet item 8 of “Final Inspection and Cleaning.”)
This bulletin contains the PDS procedures that apply specifically to 2024 model year 86 vehicles.
A universal PDS Check Sheet that contains PDS steps that apply to all 2024 model year Toyota
vehicles has been developed. To properly perform a complete PDS, you must complete all
procedures contained in this TSB as well as the universal PDS Check Sheet.
In addition, if the vehicle is stored for over 30 days, be sure to follow Long-Term Vehicle
Storage Guidelines.

© 2023 Toyota Motor Sales, USA

Page 1 of 13

T-SB-0098-23

December 6, 2023

Page 2 of 13

2024 86 Pre-Delivery Service (PDS)
Table of Contents



Warranty Policy ....................................................................................................................... 3



Warranty Information ............................................................................................................... 3



Required Tools & Equipment................................................................................................... 3



DCC Fuse Installation ............................................................................................................. 4



Front License Plate and Mounting Bracket Installation* ........................................................... 5


Drilling Procedure .............................................................................................................. 5



Installation Procedure ........................................................................................................ 7



Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation ................... 9



Installation of Rubber Body Plugs ......................................................................................... 12



Tire Pressure Warning System (TPWS) Initialization ............................................................. 13



DCM Activation* .................................................................................................................... 13
*If applicable.

© 2023 Toyota Motor Sales, USA

T-SB-0098-23

December 6, 2023

Page 3 of 13

2024 86 Pre-Delivery Service (PDS)
Warranty Policy

If the need for additional repairs or adjustment is noted during PDS, the required service should
be performed under warranty. Reimbursement will be managed under the warranty policy.
The Warranty Policy and Procedures Manual requires that you maintain the completed
Check Sheet in the customer’s file. If you cannot produce a completed form for each retailed
vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will be subject
to debit.
An additional Repair Order completed in conjunction with normal PDS MUST have time
punch/flags for service. If multiple repairs are performed, separate time flags MUST be punched
for each repair.

Warranty Information
OP CODE

DESCRIPTION

MODEL

TIME

OFP

T1

T2

001013

Pre-Delivery Service (PDS)

86

1.0

–

–

–

Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

Techstream ADVi*

QTY

TSADVUNIT

Techstream 2.0
Techstream Lite

PART NUMBER

TS2UNIT
ADE

Techstream Lite (Green Cable)

TSLITEPDLR01
TSLP2DLR01

*Essential SST.

NOTE
 Only ONE of the Techstream units listed above is required.
 GTS+ version 2023.04.003.02 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.

© 2023 Toyota Motor Sales, USA

1

T-SB-0098-23

December 6, 2023

Page 4 of 13

2024 86 Pre-Delivery Service (PDS)
DCC Fuse Installation

To minimize battery discharge, the DCC fuse (30A) has been removed and is stored in the engine
compartment relay block. Install the DCC fuse (30A) and confirm ALL related Diagnostic Trouble
Codes (DTCs) are cleared.
NOTE
Park the vehicle on level ground before performing this procedure.
Figure 1.

2

1
c

1

Relay Block

2

Remove the DCC Fuse (30A)

3

Install the DCC Fuse (30A)

3

NOTE
 With the DCC fuse (30A) removed, if ANY DTCs are detected when the ignition is turned on during
transportation, use Global Techstream Software (GTS+) to clear ALL DTCs AFTER ensuring that
there are NO malfunctions.
 While the vehicle is stored at the dealership, disconnect the negative (–) battery terminal to prevent
battery discharge. Refer to T-SB-0024-23 Battery Maintenance During PDS for battery
maintenance information.

© 2023 Toyota Motor Sales, USA

T-SB-0098-23

December 6, 2023

Page 5 of 13

2024 86 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation
Drilling Procedure

The front license plate mounting bracket set (front license plate mounting bracket, 2 bolts “1”, 2
bolts “2”, 2 J-nuts and 2 well nuts) are loaded in the luggage compartment at the assembly plant.
Follow this procedure to install the front license plate bracket and front license plate in states
where it is required by law.
1. Set the center of the front license plate mounting bracket to the center of the intake cover.
Figure 2.
B

B

A

4

A

5
6
7
3
1

2

A

Mark A

4

Bolt 1

B

Mark B

5

Bolt 2

1

Front License Plate Mounting Bracket Center

6

J-nut

2

Intake Cover Center

7

Well Nut

3

Front License Plate Mounting Bracket

2. Using the front license plate mounting bracket as a guide, make marks “A” and “B” on the
front bumper cover as shown in Figure 2.

© 2023 Toyota Motor Sales, USA

T-SB-0098-23

December 6, 2023

Page 6 of 13

2024 86 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)
Drilling Procedure (continued)

3. Remove the license plate mounting bracket
and drill 13-mm (0.51-in.) diameter holes
“A” in the front bumper cover.

Figure 3.
B

B
A

A

NOTE
Holes “A” are used to install the well nuts
and the front license plate mounting
bracket to the front bumper cover.

2

 Holes “B” are used to prevent contact
between the front bumper cover and
the bolts.

4. Drill 23-mm (0.91-in.) diameter holes “B” in
the front bumper cover.
NOTE
Holes “B” are used to prevent contact
between the front bumper cover and
the bolts.

1

A

Hole A

B

Hole B

1

13-mm (0.51-in) Diameter

2

23-mm (0.91-in) Diameter

© 2023 Toyota Motor Sales, USA

T-SB-0098-23

December 6, 2023

Page 7 of 13

2024 86 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)
Installation Procedure

1. Install the two J-nuts to the front license
plate mounting bracket as shown.

Figure 4.

1

1

2. Install the two well nuts to holes “A” in the
front bumper cover, and then fit the two