Bulletin No.: 14201
Date: May 2014

Recall Bulletin

F/CMVSS NONCOMPLIANCE RECALL
SUBJECT:

Electronic Brake Control Module

MODELS:

2014 Chevrolet Malibu
Equipped with 2.5L Engine and Auto Stop/Start (LKW&KL9)

It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or
used item of motor vehicle equipment (including a tire) covered by this notification under
a sale or lease until the defect or noncompliance is remedied.
Vehicles involved in this recall were placed on stop delivery May 7, 2014. Once the
service procedure contained in this bulletin has been performed on the vehicle, the
vehicle is released from stop delivery and the vehicle can be delivered to the customer.
All involved vehicles that are in dealer inventory must be held and not delivered to
customers, dealer traded, or used for demonstration purposes until the repair contained
in this bulletin has been performed on the vehicle.
CONDITION
General Motors has decided that certain 2014 MY Chevrolet Malibu vehicles equipped with a
2.5L engine and Auto Stop/Start (LKW&KL9) fail to conform to Federal Motor Vehicle Safety
Standard 135, Light Vehicle Brake Systems. If the vehicle experiences a complete loss of brake
vacuum assist, the hydraulic boost assist (HBA) can be disabled, causing a noncompliance with
the requirements of Section 7.11, Brake Power Assist Unit Inoperative. A disabled HBA will
cause a DIC ‘Service Brake Assist’ and ‘Check Engine’ light to be illuminated, and increased
brake pedal effort and stopping distance will be required, increasing the risk of a crash.
CORRECTION
Dealers are to reprogram the electronic brake control module.
VEHICLES INVOLVED
All involved vehicles are identified by Vehicle Identification Number on the Investigate Vehicle
History screen in GM Global Warranty Management system. Dealership service personnel
should always check this site to confirm vehicle involvement prior to beginning any required
inspections and/or repairs. It is important to routinely use this tool to verify eligibility because
not all similar vehicles may be involved regardless of description or option content.
Copyright 2014 General Motors. All Rights Reserved.

Page 2

May 2014

Bulletin No.: 14201

For dealers with involved vehicles, a listing with involved vehicles containing the complete
vehicle identification number, customer name, and address information has been prepared and
will be provided to US and Canadian dealers through the GM GlobalConnect Recall Reports.
Dealers will not have a report available if they have no involved vehicles currently assigned.
The listing may contain customer names and addresses obtained from Motor Vehicle
Registration Records. The use of such motor vehicle registration data for any purpose other
than follow-up necessary to complete this recall is a violation of law in several
states/provinces/countries. Accordingly, you are urged to limit the use of this report to the followup necessary to complete this recall.
PART INFORMATION
No parts are required.
SERVICE PROCEDURE
Note: Carefully read and follow the instructions below.


Do NOT attempt to order the calibration number from GM Customer Care and Aftersales.
The calibration numbers required for this service procedure are programmed into control
modules via a Multiple Diagnostic Interface (MDI) with the calibration update. If you cannot
access the calibration, call the Techline Customer Support Center and it will be provided.



DO NOT program a control module unless directed to by a service procedure or a service
bulletin. If the control module is not properly configured with the correct calibration software,
the control module will not control all of the vehicle features properly.



Ensure the programming tool is equipped with the latest software and is securely connected
to the data link connector. If there is an interruption during programming, programming failure
or control module damage may occur.



Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage
or loss of voltage will interrupt programming. When required install the EL-49642 SPS
Programming Support Tool to maintain system voltage. If not available, connect a fully
charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT
connect a battery charger.



Turn OFF or disable systems that may put a load on the vehicles battery such as; interior
lights, exterior lights (including daytime running lights), HVAC, radio, etc.



During the programming procedure, follow the SPS prompts for the correct ignition switch
position.



Clear DTCs after programming is complete. Clearing powertrain DTCs will set the
Inspection/Maintenance (I/M) system status indicators to NO.

1. Install EL-49642 SPS programming support tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions. Refer
to Service Programming System (SPS) documentation in SI for programming instructions.
3. On the SPS Supported Controllers screen, select K17 Electronic Brake Control Module –
Programming and follow the on-screen instructions.
4. Clear DTCs after completing the programming procedure.
5. On the SPS Supported Controllers screen, select K17 Electronic Brake Control Module Configuration and follow the on-screen instructions.

Page 3

May 2014

Bulletin No.: 14201

6. Clear DTCs after completing the Configuration procedure.
COURTESY TRANSPORTATION – For U.S. and Canada
The General Motors Courtesy Transportation program is intended to minimize customer
inconvenience when a vehicle requires a repair that is covered by the New Vehicle Limited
Warranties. The availability of courtesy transportation to customers whose vehicles are within
the warranty coverage period and involved in a product program is very important in maintaining
customer satisfaction. Dealers are to ensure that these customers understand that shuttle
service or some other form of courtesy transportation is available and will be provided at no
charge. Dealers should refer to the General Motors Service Policies and Procedures Manual
for Courtesy Transportation guidelines.
WARRANTY TRANSACTION INFORMATION
Submit a transaction using the table below. All transactions should be submitted as a ZFAT
transaction type, unless noted otherwise.
Labor
Code
9100545

Description
Reprogram Electronic Brake Control Module

Labor
Time
0.3

CUSTOMER NOTIFICATION
General Motors will notify customers of this recall on their vehicle.
DEALER RECALL RESPONSIBILITY – For U.S. States, Territories, and Possessions
It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item
of motor vehicle equipment (including a tire) covered by this notification under a sale or lease
until the defect or noncompliance is remedied.
The US National Traffic and Motor Vehicle Safety Act provides that each vehicle that is subject
to a recall of this type must be adequately repaired within a reasonable time after the customer
has tendered it for repair. A failure to repair within sixty days after tender of a vehicle is prima
facie evidence of failure to repair within a reasonable time. If the condition is not adequately
repaired within a reasonable time, the customer may be entitled to an identical or reasonably
equivalent vehicle at no charge or to a refund of the purchase price less a reasonable allowance
for depreciation. To avoid having to provide these burdensome remedies, every effort must be
made to promptly schedule an appointment with each customer and to repair their vehicle as
soon as possible. In the recall notification letters, customers are told how to contact the US
National Highway Traffic Safety Administration if the recall is not completed within a reasonable
time.
This bulletin is notice to you that the new motor vehicles included in this recall may not
comply with the standard identified above. Under Title 49, Section 30112 of the United
States Code, it is illegal for a dealer to sell a new motor vehicle which the dealer knows
does not comply with an applicable Federal Motor Vehicle Safety Standard. As a
consequence, if you sell any of these motor vehicles without first performing the recall
correction, your facility may be subject to a civil penalty for each such sale.

Page 4

May 2014

Bulletin No.: 14201

DEALER RECALL RESPONSIBILITY - All
All unsold new vehicles in dealer's possession and subject to this recall must be held and
inspected/repaired per the service procedure of this recall bulletin before customers take
possession of these vehicles.
Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of
mileage, age of vehicle, or ownership, from this time forward.
Customers who have recently purchased vehicles sold from your vehicle inventory, and for which
there is no customer information indicated on the dealer listing, are to be contacted by the dealer.
Arrangements are to be made to make the required correction according to the instructions
contained in this bulletin. A copy of the customer letter is provided in this bulletin for your use in
contacting customers. Recall follow-up cards should not be used for this purpose, since the
customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your
facility for service in the future, you must take the steps necessary to be sure the recall correction
has been made before selling or releasing the vehicle.

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that
may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the tools,
equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to
your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your vehicle may benefit from the information.

We Support
Voluntary Technician
Certification