GM Bulletin No.: 14126
Date: June 2014

Service Bulletin

SERVICE UPDATE
SUBJECT:

Service Update for Inventory and Customer Vehicles
“Peek In” Odometer Display Incorrect
Expires with Base Warranty

MODELS:

2014-2015 Chevrolet Silverado
2014-2015 GMC Sierra
2015 Chevrolet Suburban, Tahoe
2015 GMC Yukon

This service update includes vehicles in dealer inventory and customer vehicles that return
to the dealership for any reason. This bulletin will expire at the end of the involved vehicle’s
New Vehicle Limited Warranty period.
PURPOSE
This bulletin provides a service procedure to reprogram the instrument panel cluster on certain
2014-2015 model year (MY) Chevrolet Silverado and GMC Sierra vehicles. Also involved are
certain 2015 MY Chevrolet Suburban, Tahoe and GMC Yukon vehicles. These vehicles may have
an odometer reading at “Peek In” (i.e. Driver Information Center (DIC) screen when the vehicle is
in the OFF POWER mode but the cluster is awakened by opening the car door or using the key
fob) does not match the season odometer reading when the vehicle is in the RUN POWER mode.
The Trip A/B and Fuel Economy displays may also be incorrect. This condition occurs, when the
vehicle sits for an extended period of time and, normal parasitic current draws deplete the battery
state of charge to less than 12 volts and, the vehicle is in the OFF POWER mode when the cluster
is awakened as described above.
This service procedure should be completed as soon as possible on involved vehicles
currently in dealer inventory and customer vehicles that return to the dealer for any type
of service during the New Vehicle Limited Warranty coverage period.
VEHICLES INVOLVED
All involved vehicles are identified by VIN in the Global Warranty Management System –
Investigate Vehicle History Application. Dealership technicians should always check this site to
confirm vehicle involvement prior to beginning any required inspections and/or repairs. It is
important to routinely use this tool to verify eligibility because not all similar vehicles may be
involved regardless of description or option content.
Copyright 2014 General Motors. All Rights Reserved.

Page 2

June 2014

Bulletin No.: 14126

Additionally, a list of involved vehicles currently in dealer inventory is available on the “Service
Update Bulletin Information” link under the “Service” tab in GM GlobalConnect (US) or attached
to the GlobalConnect message (Canada) used to release this bulletin. Customer vehicles that
return for service, for any reason, and are still covered under the vehicle’s base warranty should
also be checked for vehicle eligibility.
PART INFORMATION
No parts are required.
SERVICE PROCEDURE
Note: Carefully read and follow the instructions below.


Do NOT attempt to order the calibration number from GM Customer Care and Aftersales.
The calibration numbers required for this service procedure are programmed into control
modules via a Multiple Diagnostic Interface (MDI) with the calibration update. If you cannot
access the calibration, call the Techline Customer Support Center and it will be provided.



DO NOT program a control module unless directed to by a service procedure or a service
bulletin. If the control module is not properly configured with the correct calibration software,
the control module will not control all of the vehicle features properly.
Ensure the programming tool is equipped with the latest software and is securely connected
to the data link connector. If there is an interruption during programming, programming failure
or control module damage may occur.
Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or
loss of voltage will interrupt programming. When required install the EL-49642 SPS
Programming Support Tool to maintain system voltage. If not available, connect a fully
charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT
connect a battery charger.
Turn OFF or disable systems that may put a load on the vehicles battery such as; interior
lights, exterior lights (including daytime running lights), HVAC, radio, etc.
During the programming procedure, follow the SPS prompts for the correct ignition switch
position.
Clear DTCs after programming is complete. Clearing powertrain DTCs will set the
Inspection/Maintenance (I/M) system status indicators to NO.
It is highly recommended that a wired MDI connection be used for the IPC updates.











In the event of an interrupted or unsuccessful programming event, perform the following
steps:
- DO NOT turn the ignition OFF. Ensure that all ECU, DLC and programming tool
connections are secure and the TIS terminal operating software is up to date.
- Attempt to reprogram the ECU.
- If the ECU can still not be programmed, turn the ignition OFF, disconnect battery, and
wait for at least two minutes.
- Connect battery, turn the ignition ON and attempt to reprogram the ECU. The ECU should
program.

Page 3

June 2014

Bulletin No.: 14126

1. Install EL-49642 SPS programming support tool.
2. Access the Service Programming System (SPS) and follow the on-screen instructions.
3. On the SPS Supported Controllers screen, select Instrument Cluster – Programming and
follow the on-screen instructions.
Note: The USB File Transfer procedure requires the use of a USB memory stick. The USB File
Transfer procedure is not required for vehicles with UDC.
4. On the SPS Supported Controllers screen, select Instrument Cluster – USB File Transfer and
follow the on-screen instructions. When prompted after installing files in vehicle via USB
memory stick, select UPDATE on radio display.
5. At the end of programming, choose the “Clear All DTCs” function on the SPS screen.
WARRANTY TRANSACTION INFORMATION
Submit a transaction using the table below. All transactions should be submitted as a ZFAT
transaction type, unless noted otherwise.
Labor
Code
9100630

Description
Reprogram Instrument Panel Cluster

Labor
Time
0.7

DEALER PROGRAM RESPONSIBILITY
Dealers must take the steps necessary to ensure that the service update correction has been
made to all involved vehicles in dealer inventory before selling or dealer-trading the vehicle, but
no later than June 30, 2015.

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that
may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the tools,
equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to
your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your vehicle may benefit from the information.

We Support
Voluntary Technician
Certification