Service Update
N232408731 Park Assist Not Enabled
Release Date:
Attention:

December 2023

Revision:

00

This service update includes vehicles in dealer inventory and customer vehicles that return to the
dealership for any reason. This bulletin will expire at the end of the involved vehicle’s New Vehicle Limited
Warranty period.

Make
Chevrolet

Model
Tahoe Police Vehicle

Model Year
From
To
2022
2022

RPO
9C1

Description
SALES PACKAGE-POLICE
VEHICLE

Involved vehicles are marked “Open” on the Investigate Vehicle History screen in GM Global Warranty Management
system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections
and/or repairs.
Condition

Correction

Certain 2022 model year Chevrolet Tahoe Police Vehicles were ordered with standard park assist and
no provision for disable option, or had the module incorrectly reprogrammed to the improper calibration
resulting enabling Front And Rear park assist.
Dealers are to select one of the options as noted in the warranty information section.

Parts
No parts are required for this repair.
Warranty Information
Labor
Operation
9106885*
9106886*
9107040*
Important:

Description
Verified Module Software or Calibration Level: Module Is
Programmed with Same Level Software or Calibration
(Option A) User Selectable Front and Rear Parking Assist via SPS2
(Option B) Front Parking Assist Disable via SPS2 (With call to TCSC)

Labor
Time

Trans.
Type

Net
Item

ZFAT

N/A

0.2
0.3
0.3

* To avoid warranty transaction rejections, carefully read and follow the instructions below:

6125814

•

The Warranty Claim Code from the programming event must be accurately entered in the “Warranty Claim
Code” field of the transaction.

•

When more than one Warranty Claim Code is generated for a programming event, it is required to document all
Warranty Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the
“Warranty Claim Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter
the FINAL code provided by SPS2.

Copyright 2023 General Motors. All Rights Reserved.

Page 1 of 7

Service Update
N232408731 Park Assist Not Enabled
Warranty Claim Code Information Retrieval

6125774

If the Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS2 system as
follows:
1.
2.
3.
4.

Open TLC on the computer used to program the vehicle.
Select and start SPS2.
Select Settings (1).
Select the Warranty Claim Code tab (2).

The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is
retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code
field.
Service Procedure
Caution: Before downloading the update files, be sure the computer is connected to the internet through a network cable
(hardwired). DO NOT DOWNLOAD or install the files wirelessly. If there is an interruption during programming,
programming failure or control module damage may occur.
Note: Carefully read and follow the instructions below.

•

Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector.
If there is an interruption during programming, programming failure or control module damage may occur.

•

Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will
interrupt programming. Install a GM Authorized Programming Support Tool to maintain system voltage. Refer to
www.gmdesolutions.com for further information. If not available, connect a fully charged 12 V jumper or booster
pack disconnected from the AC voltage supply. DO NOT connect a battery charger.

•

Follow the on-screen prompts regarding ignition power mode, but ensure that anything that drains excessive power
(exterior lights, HVAC blower motor, etc) is off.

•

Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M)
system status indicators to NO.

Important: The service technician always needs to verify that the VIN displayed in the TLC left side drop down menu and
the top center window match the VIN plate of the vehicle to be programmed prior to using Service Programming System
2 (SPS2) for programming or reprogramming a module.

•

For the TLC application, service technicians need to always ensure that the power mode (ignition) is “ON” before
reading the VIN from the vehicle’s VIN master module and that they do not select a VIN that is already in the TLC
application memory from a previous vehicle.

Page 2 of 7

Service Update
N232408731 Park Assist Not Enabled
•

If the VIN that shows up in the TLC top center window after correctly reading the VIN from the vehicle does not match
the VIN plate of the vehicle, manually type in the VIN characters from the vehicle VIN plate into the TLC top center
window and use these for programming or reprogramming the subject module with the correct vehicle VIN and
software and/or calibrations.

•

The Engine Control Module (ECM) is the master module (for VIP vehicles) that TLC reads to determine the VIN of
the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the ECM also needs
to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate.

•

The Body Control Module (BCM) is the master module (for GEM vehicles) that TLC reads to determine the VIN of
the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the BCM also needs
to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate.

Caution: Be sure the VIN selected in the drop down menu (1) is the same as the vehicle connected (2) before beginning
programming.

5743643

Important: If the vehicle VIN DOES NOT match, the message below will be shown.

5877000

5644477

Page 3 of 7

Service Update
N232408731 Park Assist Not Enabled
Important: Techline Connect screens shown above.
Important: If the same calibration/software warning is noted on the TLC Summary screen, select OK and follow
screen instructions. After a successful programming event, the WCC is located in the Service Programming System
dialogue box of the SPS Summary screen. No further action is required. Refer to the Warranty section of the bulletin.
1.

Inspect vehicle for front push bumper.
• If the vehicle does not have a front push bumper, proceed to “(Option A) User Selectable Front and Rear Parking
Assist.” Selection latches over key cycles.
• If the vehicle is equipped with a front push bumper, ask the customer if they want to disable ONLY the Front
Parking Assist and leave the Rear Parking Assist functional (not driver selectable), OR have the ability to toggle
both the Front and Rear Parking Assist either both “On” or both “Off” (Driver selectable with latching over key
cycles).
A. If the Customer wants to toggle both the Front and Rear Parking Assist either both “On” or both
“Off”, proceed to “(Option A) User Selectable Front and Rear Parking Assist.” This selection latches
over key cycles.
B. If the Customer wants to ONLY disable the Front Parking Assist, leaving the Rear Parking Assist
operational, proceed to “(Option B) Front Parking Assist Disable.”
Note: RPO SK5 will permanently disable the Front Parking Assist feature ONLY. The Rear Parking Assist will remain
functional.
(Option A) User Selectable Front and Rear Parking Assist
Note: This option will allow for both Front and Rear Parking Assist to be either both enabled OR both disabled.
1.
2.

Reprogram the Parking Assist Control module. Refer to K182 Parking Assist Control Module: Programming and Setup
in SI.
Turn Parking Assist either “On” or “Off’ through the vehicle’s menu, based on what the customer desires. See next
steps for instructions on how to enable or disable the Parking Assist feature.

6493764

3.

Touch the “Settings” icon on the Home Page of the infotainment display.

Page 4 of 7

Service Update
N232408731 Park Assist Not Enabled

6493765

4.

Touch Vehicle to display a list of available options. Select “Collision/Detection Systems.”

5.

Touch to select “Park Assist” in the menu.

6493766

Page 5 of 7

Service Update
N232408731 Park Assist Not Enabled

6493767

6.

Touch to select either “Off” or “Alert” based on what the customer wants. After the selection has been made, close
out of the menu.

(Option B) Front Parking Assist Disable
Note: RPO SK5 will permanently disable the Front Parking Assist feature ONLY. The Rear Parking Assist will remain
functional.
1.

Contact Techline Customer Support Center (TCSC) and request for VIN to be equipped with RPO “SK5”.

2.

Reprogram the Parking Assist Control module. Refer to K182 Parking Assist Control Module: Programming and
Setup in SI.

5644478

Note: The screenshot above is an example of module programming and may not be indicative of the specific module
that is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the
Warranty Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the
WCC on the screen.
2.

Record SPS Warranty Claim Code on job card for warranty transaction submission.

Page 6 of 7

Service Update
N232408731 Park Assist Not Enabled
Dealer Responsibility
Whenever a vehicle subject to this service update enters your vehicle inventory or is in your facility for service in the
future, and the vehicle is still covered under the New Vehicle Limited Warranty, you must take the steps necessary to be
sure the service update correction has been made before selling or releasing the vehicle.
All new, used, GM Certified Pre-Owned (CPO), courtesy transportation vehicles, dealer shuttle vehicles, CarBravo, etc.
in dealers' possession and subject to this field action must be held and inspected/repaired per the service procedure of
this bulletin before customers take possession of these vehicles. Involved vehicles must be held and not delivered to
customers, dealer-traded, released to auction, used for demonstration, or any other purpose.
All GM Certified Pre-Owned (CPO) vehicles currently in the dealers’ inventory within the SHIFT Digital system will be
de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting an accepted/paid
warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified for sale within
the SHIFT Digital system, or once again be used in the Courtesy Transportation Program.
Dealer Reports – For USA & Export
The Inventory tab of the Open Vehicle Report will contain Service Update Bulletin VINs that apply to this field action.
This information is intended to assist dealers with the PROMPT COMPLETION of these vehicles. The Customer InService tab will not contain Service Update Bulletin VIN data because the intent of a Service Update Bulletin is to not
inconvenience a customer with a special trip for service. Service Update Bulletins are to be completed when the
customer is in for a regularly scheduled visit.

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.

We Support
Voluntary Technician
Certification

Page 7 of 7

GLOBAL SAFETY FIELD INVESTIGATIONS
DCS6741
URGENT - DISTRIBUTE IMMEDIATELY
Date:

December 13, 2023

Subject: N232408731 - Service Update
Park Assist Not Enabled
Models: 2022 Chevrolet Tahoe Police Vehicle
Equipped with SALES PACKAGE-POLICE VEHICLE (RPO 9C1)
To:

All General Motors Dealers

General Motors is releasing Service Update N232408731 today. The total
number of U.S. vehicles involved is 1,477. Please see the attached bulletin for
details.
Global Warranty Management (GWM)
The Required Field Action section on the Investigate Vehicle History (IVH) screen will
be updated December 13, 2023. A Stock VIN list is not included as our records show
there are no vehicles in dealer new inventory.
END OF MESSAGE
GLOBAL SAFETY FIELD INVESTIGATIONS