NHTSA ID Number: 10246647
Manufacturer Communication Number: 130522001B
TSB/Document Date: 2023-12-11
Summary
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
File in Section:
Bulletin No.:
Service Bulletin
Date:
05 - Brakes
13-05-22-001B
September, 2014
INFORMATION
Subject:
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
Models:
2000-2006 Cadillac
Escalade Models
2000-2006 Chevrolet Avalanche, Suburban, Tahoe
1999-2007 Chevrolet Silverado
2000-2006 GMC Yukon Models
1999-2007 GMC Sierra
This bulletin has been revised to emphasize the continued availability of pre-formed and
pre-flared hydraulic brake pipe kits. Please discard bulletin 13–05–22–001A.
The purpose of this bulletin is to inform dealers of an
improved service strategy to aid in the replacement of
hydraulic brake pipes for the above listed vehicles.
Customer Care and Aftersales (CCA) has released
pre-formed and pre-flared hydraulic brake pipe kits.
These kits can be used anytime replacement of the
entire brake pipe assemblies is required. These kits
include all the pre-formed and pre-flared brake pipes
needed when replacing the entire brake pipe assembly,
except the rear axle crossover pipe. If the rear axle
crossover pipe requires replacement, refer to the
appropriate parts catalog for ordering and the Brake
Pipe Replacement procedure in SI for installation
instructions. The following procedure describes how to
install these kits.
Replacement Procedure (Pickup and
Cab Chassis)
Removal
Warning: Brake fluid may irritate eyes and skin. In
case of contact, take the following actions:
• Eye contact—rinse thoroughly with water.
• Skin contact—wash with soap and water.
• If ingested—consult a physician immediately.
Caution: Avoid spilling brake fluid onto painted
surfaces, electrical connections, wiring, or cables.
Brake fluid will damage painted surfaces and cause
corrosion to electrical components. If any brake fluid
comes in contact with painted surfaces, immediately
flush the area with water. If any brake fluid comes in
contact with electrical connections, wiring, or cables,
use a clean shop cloth to wipe away the fluid.
Caution: Care should be taken to ensure that dirt,
water, grease, or other contaminants do not enter the
new brake pipes and threaded end fittings when the
pipes are being installed into the vehicle. Use tape or
Copyright 2014 General Motors LLC. All Rights Reserved.
other appropriate methods to cover the threaded end
fittings and the ends of the pipes to prevent dirt, water,
grease, or other contaminants from entering the pipes.
Remove all protective measures before connecting the
end fittings to the master cylinder, brake pressure
proportioning valve (where equipped), brake pressure
modulator valve (BPMV), or flexible brake hoses.
Caution: Cleanliness is important for the proper
function of the hydraulic brake system. Clean all dirt,
water, rust, etc from the areas adjacent to each brake
pipe tube nut before removing the brake pipe tube nuts.
Take care to ensure that no contaminants enter any
hydraulic fittings or openings during removal or
installation of the brake pipes.
Caution: Before removing any brake pipes from the
master cylinder, ABS module (BPMV), and the brake
pressure proportioning valve (where equipped) identify
the port locations. On the BPMV identify the port
location for each hydraulic component (e.g., Master
Cylinder Primary, Master Cylinder Secondary, LF
corner, RF corner, LR corner, RR corner, Rear Brake).
On the brake pressure proportioning valve identify the
port locations for each hydraulic component (e.g.
master cylinder primary inlet, master cylinder primary
outlet, master cylinder secondary inlet, master cylinder
secondary outlet, pre-charge pump). When installing
the replacement pipes, ensure that the replacement
pipes are installed in the correct port locations on the
master cylinder, BPMV, and brake pressure
proportioning valve, where equipped. If the pipes are
not installed in the correct port locations on all the
hydraulic components, the brake system including the
ABS system and/or TCS/VSES Stabiltrak system
(where equipped) will not operate correctly and may
result in damage to the hydraulic brake components.
Note: This procedure does not comprehend specific
vehicle models or brake system configurations. The
illustrations may not exactly reflect the vehicle being
repaired. Some LD pickups and LD SUVs may be
Page 2
September, 2014
equipped with a brake pressure combination valve and
a brake pressure modulator valve pre-charge pump.
The brake pipes attached to these components should
be removed and replaced with the replacement pipes
provided in the service kit.
Note: This procedure is not intended for the repair or
replacement of a single damaged brake pipe. This
procedure is for the replacement of the entire brake
pipe assemblies with pre-formed and pre-flared
components.
Note: Remove the brake pipes from the existing
routing clips carefully to avoid damaging the clips as all
the clips will be re-used. The new brake pipes will be
reinstalled into the existing clips. After installing the
new brake pipes, inspect the routing of the brake pipes
to ensure that the new brake pipes do not contact or
rub on any frame, body, or chassis components.
Carefully bend the pipes to increase clearance as
required.
Note: The brake pipes in these kits are not an exact
duplicate of the pipes currently installed on the vehicle.
These pipes have a nylon coating to provide better
corrosion protection and may have slightly different
shapes and bends and may not exactly match the
brake pipes being replaced. Some original equipment
pipes may use flexible hose sections near the master
cylinder or brake pressure proportioning valve that
attaches to the master cylinder to brake booster
mounting studs. The replacement pipes in this kit will
not use the flexible hose sections. The replacement
pipes have been designed to fit each vehicle
application. Because of the nylon coating on the
outside of the brake pipes, the outside diameter of the
pipe is slightly larger than the original pipes, Extra effort
may be required to insert the pipes into the existing
mounting clips. It is recommended to finger start all the
threaded end fittings into the master cylinder, brake
pressure proportioning valve, brake pressure
modulation valve, and flexible brake hoses before
performing the final tightening and torque of each
fitting.
Note: The brake pipes in these kits may have
additional large radius shipping bends to allow the
pipes to fit within the cardboard box. Those pipes with
additional shipping bends will have tags on either side
of each shipping bend. Carefully straighten the section
of pipe between the tags to remove the shipping bend.
Take care not to kink or damage the brake pipes. If a
brake pipe becomes kinked or damaged while
removing the shipping bends, it must be repaired or
replaced before installation into the vehicle. Take care
not to cut, nick, abrade or otherwise damage the nylon
coating on the brake pipes during installation.
Note: For Chassis Cab models, due to the installation
and mounting of the aftermarket equipment/body on the
rear of the chassis (i.e. flatbed, stake bed, box van,
Bulletin No.: 13-05-22-001B
dump body, etc) by the second stage manufacturer or
vehicle upfitter, it may be difficult or prohibitive to
remove the aftermarket body to enable replacement of
the OEM rear brake pipe. Each vehicle will need to be
assessed individually, however, it may be preferable to
hand bend a service replacement brake pipe using GM
P/N 88936298 PIPE, BRK (STEEL) (1/4" X 16 FT
ROLL) nylon coated bulk tubing available separately
from GM dealers, using GM P/N 15103241 Fitting, BRK
PIPE (1/2-20-2A THD) (1/4 TUBE STL) to attach to the
ABS module (BPMV) and GM P/N 11609443 Tube Nut
(7/16-24 UNS-2A THD) to attach to the rear axle jounce
hose. These tube nuts are designed to properly fit over
the nylon coated brake tubing. The tube nuts can also
be removed from the replacement rear pipe included in
the brake pipe service kit and installed on the hand
bent service replacement pipe. Route the hand bent
service replacement pipe from the ABS module
(BPMV) to the rear axle jounce hose ensuring adequate
clearance is maintained between the pipe and
surrounding components to ensure that the pipe is not
damaged in service. Attach the hand bent service
replacement brake pipe securely to the chassis using
brake pipe clips, rubber coated P-clips, or other
suitable methods. The maximum distance between
attachment points or clips should not exceed 457 mm
(18"). If a brake pipe has a directional change (bend) of
30 degrees or more, a clip needs to be located as close
as possible to the bend.
3339728
1. Disconnect the master cylinder secondary (1) and
primary (2) brake pipe fittings from the master
cylinder.
2. Plug the master cylinder outlet ports to prevent
brake fluid loss and contamination.
Bulletin No.: 13-05-22-001B
September, 2014
3339729
3. For vehicles equipped with a combination valve,
disconnect the master cylinder secondary (1) and
primary (2) brake pipe fittings from the combination
valve.
4. Plug the combination valve inlet ports to prevent
brake fluid loss and contamination.
Page 3
8. Apply ACDelco Rust Penetrant and Inhibitor
10-4020 (GM P/N 88862628) or equivalent
penetrating lubricant to the bleeder screws of the
following components:
• Front brake calipers
• Rear brake calipers
9. Apply ACDelco Rust Penetrant and Inhibitor
10-4020 (GM P/N 88862628) or equivalent
penetrating lubricant to the brake pipe fitting tube
nuts at the following locations:
• Front brake hoses
• Brake pressure modulator valve (BPMV)
• Rear brake hose(s)
10. Remove the left and right front wheelhouse panels.
Refer to Wheelhouse Panel Replacement in SI.
11. Remove the engine protection shield, if equipped.
Refer to Engine Protection Shield Replacement
in SI.
12. Reference mark the parking brake front cable
adjuster nut at the equalizer and disconnect the
parking brake front cable. Refer to Parking Brake
Front Cable Replacement in SI.
13. Disconnect any wiring ground harnesses from the
body to the frame. Refer to Power and Grounding
Component Views in SI
14. Remove the 3 left side body mount bolts and the
core support mount bolt. Refer to Drivetrain and
Front Suspension Frame Insulator Replacement
in SI.
Note: Only raise the body enough to gain hand
access to the brake pipe routing clips. Pay careful
attention to avoid stressing hoses and wiring
harnesses.
15. Carefully raise the left side of the body from
inboard of the frame rails
approximately 51 mm (2 in).
Note: Place the support blocks inboard of the frame
rails and as close to the body mounting points as
possible to evenly distribute the weight of the
vehicle body.
3339730
5. For vehicles equipped with a combination valve,
disconnect the secondary (1) and primary (2) brake
pipe fittings from the combination valve.
6. Raise and support the vehicle. Refer to Lifting and
Jacking the Vehicle in SI.
7. Remove the front and rear tire and wheel
assemblies. Refer to Tire and Wheel Removal and
Installation in SI.
16. Place blocks or supports inboard of the frame side
rails to support the body in at least 3 locations.
17. Remove the left side pickup box bolts and loosen,
but do not remove, the right side pickup box bolts.
Refer to Pickup Box Replacement in SI.
Note: Only raise the pickup box enough to gain hand
access to the brake pipe routing clips. Pay careful
attention to avoid stressing hoses and wiring
harnesses.
18. Carefully raise the left side of the pickup box
approximately 51 mm (2 in).
Note: Place the support blocks as close to the pickup
box mounting points as possible to evenly distribute the
weight of the vehicle body.
19. Place blocks or supports inboard of the frame side
rails to support the pickup box in at
least 3 locations.
20. Release the body wiring harness conduit from the
brake pipe retainers on the left side of the vehicle.
Page 4
September, 2014
Bulletin No.: 13-05-22-001B
21. Position and secure the wiring harness aside.
2728198
2727389
26. Release the right front brake pipe from the front
frame crossmember clips (1).
22. Using side cutters, cut the right front brake pipe as
close as possible to the brake pipe fitting (1) at the
brake hose.
23. Using a 6 point socket, remove and discard the
right front brake pipe fitting tube nut.
24. Disconnect the left front wheel speed sensor
electrical connector and remove the sensor
harness retaining clips from the top of the left
frame rail.
2728205
27. Release the right front brake pipe from the left front
frame rail clips (1).
2728189
25. Release the right front brake pipe from the
clips (1) on the right frame rail.
Bulletin No.: 13-05-22-001B
September, 2014
2728215
28. Using side cutters, cut the left front brake pipe as
close as possible to the brake pipe fitting (1) at the
brake hose.
29. Using a 6 point socket, remove and discard the left
front brake pipe fitting tube nut.
30. Release the front brake pipes assembly from the
left frame rail clip (2).
Page 5
3339723
Note: Due to the similarity of the brake pipe fitting tube
nuts, it is imperative to identify the individual brake pipe
locations on the BPMV to ensure correct assembly.
33. Identify the brake pipe port locations at the BPMV
prior to disconnecting the brake pipe fittings.
2728225
2728220
31. Release the front brake pipes assembly from the
left frame rail clips (1).
32. Clean the area surrounding the brake pipe fittings
on the BPMV thoroughly to remove all dirt and
debris.
34. Using side cutters, cut the left front (1) and right
front (2) brake pipes as close as possible to the
brake pipe fittings at the BPMV.
35. Using a 6 point socket, remove and discard the
front brake pipe fitting tube nuts.
Page 6
September, 2014
2728241
36. Using side cutters, cut the master cylinder
primary (1) and secondary (2) brake pipes as close
as possible to the brake pipe fitting at the BPMV.
37. Using a 6 point socket, remove and discard the
brake pipe fitting tube nuts.
38. Carefully remove the brake pipe routing clips from
the front brake pipe assembly.
39. Maneuver the front brake pipes one at a time and
remove the brake pipes from the vehicle.
Bulletin No.: 13-05-22-001B
2728250
42. Release the rear brake pipe from the left frame rail
clips (1).
2728259
43. Release the rear brake pipe from the left frame rail
clips (1).
2728234
40. Using side cutters, cut the rear brake pipe (1) as
close as possible to the brake pipe fitting at
the BPMV.
41. Using a 6 point socket, remove and discard the
brake pipe fitting tube nut.
Bulletin No.: 13-05-22-001B
September, 2014
Page 7
2728497
44. Using side cutters, cut the rear brake pipe (1) as
close as possible to the brake pipe fitting at the
rear brake hose.
45. Using a 6 point socket, remove and discard the
rear brake pipe fitting tube nut.
46. Remove the rear brake pipe from the vehicle.
2728497
1. Install the rear brake pipe.
2. Install the rear brake pipe fitting tube nut (1).
Tighten
Tighten the nut to 25 Y (18 lb ft)
Installation
Caution: Use the correct fastener in the correct
location. Replacement fasteners must be the correct
part number for that application. Do not use paints,
lubricants, or corrosion inhibitors on fasteners, or
fastener joint surfaces, unless specified. These
coatings affect fastener torque and joint clamping force
and may damage the fastener. Use the correct
tightening sequence and specifications when installing
fasteners in order to avoid damage to parts and
systems. When using fasteners that are threaded
directly into plastic, use extreme care not to strip the
mating plastic part(s). Use hand tools only, and do not
use any kind of impact or power tools. Fastener should
be hand tightened, fully seated, and not stripped.
2728259
3. Install the rear brake pipe to the left frame rail
clips (1).
Page 8
September, 2014
Bulletin No.: 13-05-22-001B
2728250
4. Install the rear brake pipe to the left frame rail
clips (1).
2728225
6. Install the right front brake pipe fitting tube nut (2).
Tighten
Tighten the nut to 25 Y (18 lb ft)
7. Install the left front brake pipe fitting tube nut (1).
Tighten
Tighten the nut to 25 Y (18 lb ft)
3339723
Note: Due to the similarity of the brake pipe fitting tube
nuts, it is imperative to identify the individual brake pipe
locations on the BPMV to ensure correct assembly.
5. Connect the brake pipe fittings to the BPMV port
locations identified during removal.
2728234
8. Install the rear brake pipe fitting tube nut (1).
Tighten
Tighten the nut to 25 Y (18 lb ft)
Note: Install the brake pipes to the routing clips and
retaining clips after all the brake pipes are fitted to the
vehicle.
9. Install the master cylinder primary and secondary
brake pipe assembly to the vehicle.
Bulletin No.: 13-05-22-001B
September, 2014
Page 9
2728241
10. Install the master cylinder primary brake pipe fitting
tube nut (1).
Tighten
Tighten the nut to 25 Y (18 lb ft)
11. Install the master cylinder secondary brake pipe
fitting tube nut (2).
2728215
13. Install the left front brake pipe fitting tube nut (1).
Tighten
Tighten the nut to 25 Y (18 lb ft)
14. Install the front brake pipes assembly to the left
frame rail clip (2).
Tighten
Tighten the nut to 25 Y (18 lb ft)
2728205
15. Install the right front brake pipe to the left front
frame rail clips (1).
2728220
12. Install the front brake pipes assembly to the left
frame rail clips (1).
Page 10
September, 2014
2728198
16. Install the right front brake pipe to the front frame
crossmember clips (1).
2727389
- Mixes well with conventional fluids
- Low-moisture formula provides excellent vapor lock...
- Ideal for hydraulic and disc brakes
- Provides an extra margin of safety in extreme braking...
- Mix of polyglycol ethers ensures hot brake-system operation...
- Excellent for ABS, disc and drum brake systems
- Delivers braking power when needed by avoiding a spongy...
- Both wet and dry boiling points exceed the minimum...
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 130522001B
Replacement Service Bulletin Number:
MFR Communication Date: 2014-09-01
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: SERVICE BRAKES
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- Obd2 Bluetooth Scanner Lifetime Update: Ediag Elite offers revolutionary Advantage Lifetime Updates with unlimited access to the superior 15 reset service, bidirectional testing and full system diagnostics.The Ediag Elite is an excellent Bluetooth obd2 scanner diagnostic tool ideal for diy's and private car owners
- Bidirectional Control for Quickly Locating Problems: The Bidirectional Scan tool allows you to send commands directly from your smartphone to your vehicle for active testing. This feature helps to quickly narrow down problems such as air conditioning clutches, windows, doors, sunroofs, etc., reducing diagnostic time for mechanics and helping Diy users locate faults more easily. In addition, Ediag Elite provides fault analysis and repair guidance to help you solve problems efficiently.
- 15 Maintenance Resets: The current version introduces 15 popular special features: Oil Reset, Headlight Matching, Bleeding Reset, TPMS Reset, BMS Reset, Gear Box Relearn, Throttle Learning, Injector Coding, SAS Reset and more special functions in system diagnose menu. These functions make it easy for owners to carry out the necessary maintenance and servicing, ensuring that your vehicle stays in top condition, prolonging its service life and preventing common problems and breakdowns. Note: The Special function vary by model& year, Reach us check compatibility.
- Wide Compatibility CANFD & FCA
Autoauth: Compatible with GM, Ford, Toyota, Chrysler, Honda, Mazda, Nissan, Mitsubishi, Hyundai, KIA with standard OBD2 port from 1996 to newer. More car brands and features will be released gradually. Newest Ediag Elite scanner supports CANFD Protocol and FCA cars. Note: Coverage may vary on different vehicle by model& year ,Please contact us to confirm compatibility before purchase. - Perfect for Monitoring The Health of Your Vehicle: Ediag Elite is designed to make vehicle maintenance simple and efficient. With intelligent AutoVIN quick recognition, it is easy to connect to your car without the need for manual input. Real-time data is visualized in a variety of formats, including graphs, numeric, meter displays and clear 4-in-1 data charts, allowing you to effortlessly monitor real-time data. Data logging/reporting is available for playback and further analysis.
- No Annual Fees & 2026 Upgraded CAN FD: Why pay $199/year or more for updates? The 2026 newest Kingbolen K7 obd2 scanner features have been upgraded to Lifetime Updates without subscription fees, saving you significant costs in the long run. K7 scan tool also adds the CAN FD protocol for the latest GM models (2019+), enabling faster data transfer, reducing the risk of undetected errors
- 2026 Newest Top-tier Car Scanner: Kingbolen K7 diagnostic scan tool is equipped with most capabilities for daily repair/maintenance: Wireless diagnosis via Bluetooth, Bidirectional Test, ECU Online/Offline Code, 31+ Resets, PMI for Ford, Lincoln, Mazda, Global version for 100+ brand vehicles and 17 languages, no area limit, FCA AutoAuth
- OE-Level Full Systems Scan Tool: K7 professional diagnostic scanner with Auto Vin can do one-click to scan ECUs on most of vehicles, like pcm, ecm, eps, bcm, tpms, sas, a/c system... to read/clear code, view live data, freeze frame, read ecu info. 4-in-1 data stream graphics can make data viewing more intuitive. Detailed diagnostic reports will help you easily master the car situation as it can be shared by bluetooth or email! Adding workshop information can help your customers to know more
- Bidirectional Test/Active Test & ECU Code: Stop guessing and start fixing. Bidirectional scan tool Kingbolen K7 can perform real active test that can send commands to the vehicle's ECU to drive the actuators to work, like window, rear mirrors, sunroof, door, solenoids, wipers, headlamp, etc, helping you quickly find out bad parts and pinpoint faulty issues. K7 bidirectional scanner will be a good choice to save money and time on car repairs when performing complex maintenance and repair
- 31 Reset Functions: Avoid expensive dealership visits for simple services. Experience tells us that just a small repair service may cost a lot of money. Kingbolen K7 is a professional diagnostic scanner with 31 common maintenance services like Oil /SAS/EPB/TPMS Reset, Battery Matching, ABS Bleeding, Injector Code, etc. It effectively handles most of the car reset and relearning jobs, perfect for experienced DIYers and mechanics. Note: Functions in the menu vary across vehicles. Kindly check the compatibility before purchase
- 【Lifetime Database & Software Updates— No Subscription Fee, No Feature Lock, Save you $399/Y】KINGBOLEN K8 Pro's software can already be permanently upgraded and used for while software of other same price product still needs annual fee of almost $400. K8 pro scanner has packed all capabilities auto technicians would ever need for repair & maintenance services: Added CAN-FD & DOIP protocol, Bluetooth Wireless Diagnosis, Bidirectional Test, ECU Online/Offline Code & Guided Functions for VW, for Audi...34+ Restes, Autoauth for FCA SGW, Larger 4GB+64GB memory, 12600mAh battery, 8'' touch screen with 1280 * 800 Resolution. A Kickstand can allow the tablet to sit at a comfortable angle
- 【Newly Added CAN FD & DOIP Protocol】As Upgrade Version of Kingbolen K8, K8 Pro obd2 scanner supports CANFD and DOIP protocol, which will save you 200+ bucks as no need extra buy for special adapter. CANFD protocol suits for the latest GM(2019-), reducing the risk of undetected errors. The DoIP protocol (comes with DoIp cable) fits for 2017+ BMW(F&G chassis), for Jaguar & Land Rover after 2017, for Volvo after 2018. Plus, K8 Pro's Memory from 2G+32G expanded to 4G+64G, update period extended from 2 years to permanent
- 【34+ Hot Special Functions & V.A.G Guide】KINGBOLEN K8 pro bluetooth obd2 scanner covers almost all common services including Oil Reset, EPB, SAS, BMS Reset, ABS bleed, Throttle Reset, Suspension, Injector Code, Power Balance, Transmission Adaptation, Fuel Trim Learn, HVAC Control Module Calibrate, Language Change, A/F Settings, Stop/Start Reset, Crankshaft Sensor Relearn, TPMS, PMI function and etc. Imagine how much money and time you spend on car maintenance every year? K8 pro car scanner will be a good helper and saver for your car. V.A.G Guided function provides step-by-step guide to work for Volkswagen/Audi/Skoda. Note: Please send us model/year/vin to check compatibility before order
- 【Powerful Bidirectional Test/Active Test & ECU Code】As a bidirectional scan tool, KINGBOLEN K8 pro allows you to request information from a vehicle's ECU or send commands to the vehicle's modules to perform specific tests and functions, such as EVAP Tests, Turn on/off radiator fan, Window/Mirror/Door Lock Test, Pump and Value Tests, Sound horn Test, et. Without using the vehicle control system and dismantling car’s parts, it can quickly and accurately pinpoint the fault causes, simple operation saves time and money
- 【Wireless OE-Level All Systems Diagnostics】Equipped with Bluetooth VCI, you can do car diagnostics out of the car (up to 33F/10M) without being confined to a small space inside the car. Provides the convenience of Auto VIN, K8 pro allowing for easy access and diagnosis of all available modules on a wide range of vehicles, like PCM, ECM, BCM, TPMS, SAS, Fuel System, etc, to perform read/clear codes, view live data, freeze frame, perform active tests, and read ECU info... 12-In-1 Data Stream Graphics make data viewing more intuitive.Diagnostic reports can be shared via QR Code, Bluetooth or email.Built-in Browser and Fault Code Library allows you directly query the fault code when diagnosing
Last update on 2026-06-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.