Installation and Conversion Instructions

911 (992)
13 / 21 ENU

6600

6

SportDesign Package/Aerokit

Revision:

This bulletin replaces bulletin Group 6 13/21, dated July 7, 2022.

Vehicle Type:

992

Model Year:

As of 2019

Information:

Retrofitting

Figure 1
Scope 1 – SportDesign front apron
Scope 2 – SportDesign package, front and rear apron
Scope 3 – Aerokit, comprising a fixed rear wing, Important: Aerokit is only approved and tested in
conjunction with SportDesign front and rear apron package Scope 2.
NOTICE
Aerokit
•

Aerokit is only approved and tested in conjunction with SportDesign package Scope 2!

Tequipment

Nov 17, 2023
Page 1 of 10

6

911 (992)
6600

Part No.:

ENU

Installation and Conversion Instructions

13/21

Important: Only the order sets are listed; current exploded drawings or a detailed list of the parts are
visible in the PET (Porsche Electronic Parts Catalogue).
Important: Wiring harnesses for the front and rear apron must also be ordered separately. Transfer
installed I-numbers and order the relevant wiring harness for the SportDesign package and Aerokit.
Package Order
Number
992.044.830.A

1x

Front apron with ParkAssist 7X2

992.044.831.A

1x

Front apron with Park (Steering) Assist 7X5

Package Order
Number
992.044.846

1x

992.044.846.A

1x

992.044.846.B

1x

992.044.846.C

1x

Package Order
Number
992.044.841

Work
Procedure:

Scope 1: SportDesign package front apron

Scope 2: SportDesign package front and rear apron
Complete SportDesign package for 992 C2/C4 USA with
ParkAssist, with camera for Coupé without sports exhaust
system, and with sports tailpipe
Complete SportDesign package for 992 C2/C4 USA
with ParkAssist, with camera for Cabriolet without sports
exhaust system, and with sports tailpipe
Complete SportDesign package for 992 C2/C4 USA with
ParkAssist, with camera for Coupé with sports exhaust
system
Complete SportDesign package for 992 C2/C4 USA with
ParkAssist, with camera for Cabriolet with sports exhaust
system
For Scope 2: Rear part, SportDesign package
1x

SportDesign rear part for 992 C2/C4 USA with ParkAssist,
with camera

Package Order
Number
992.044.880

Scope 3: Aerokit
1x

Aerokit with Galvano Silver vanes

992.044.881

1x

Aerokit with prime-coated vanes

Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be
performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the
steps shown.
Information
The number of electric plug connections and clips will vary depending on equipment.
Important: Paint ready-primed parts only! Paint the removed parts. This information applies to all work
steps (Scope 1 – 3).

Nov 17, 2023
Page 2 of 10

Tequipment

Installation and Conversion Instructions

911 (992)
13 / 21 ENU

6600

6

CAUTION
Painting components
•

Risk of warping of components

•

Risk of damage to components



Observe the guidelines and instructions for painting components in the "Paint" Workshop Manual.



Always place parts without tension on the painting devices provided during painting and drying processes.
1

2

The following work steps concern Scope 1 and 2.
1.1

Connecting a battery charger.  Workshop Manual 'Charging battery/vehicle electrical
system'

1.2

Raise the vehicle.  Workshop Manual 'Raising vehicle'

1.3

Remove the front apron.  Workshop Manual 'Removing and installing front apron'

1.4

Replace bumper.  Workshop Manual 'Removing and installing front bumper'

1.5

Replace left and right side guides  Figure 2
-1-.

1.6

Disassemble and assemble front apron. 
Workshop Manual 'Replacing front apron'

1.7

Installing front apron.  Workshop Manual
'Removing and installing front apron'

The following work steps concern Scope 2.
Important: Pay particular attention to the following
when painting.  Workshop Manual 'Instructions
for painting rear apron (vehicles with Lane Change
Assist)'

Figure 2

2.1

Remove rear apron.  Workshop Manual 'Removing and installing rear apron'

2.2

Disassembling and assembling rear apron.  Workshop Manual 'Replacing rear apron'

2.3

Remove bumper.  Workshop Manual 'Removing and installing rear bumper'

2.4

Install heat shield on bumper.

Tequipment

Nov 17, 2023
Page 3 of 10

6

911 (992)
6600

ENU

13/21
2.4.1

Installation and Conversion Instructions
Screw left and right holders to the
bumper using two nuts on each side
 Figure 3 -1-.

Figure 3
2.4.2

Install air guide  Figure 4 -1- with
one nut  Figure 4 -2-.

Figure 4
2.4.3

Install heat protection  Figure 5
-1- with six nuts  Figure 5 -2-.

Figure 5

Nov 17, 2023
Page 4 of 10

Tequipment

Installation and Conversion Instructions
2.4.4
2.5

911 (992)
13 / 21 ENU

6600

6

Install foam  Figure 6 -1- on the
bumper.

Remove charge-air cooler.  Workshop
Manual 'Removing and installing charge-air
cooler'

Figure 6

3

2.6

Replace charge-air cooler air guides  Figure
7 -1-.

2.7

Install charge-air cooler.  Workshop Manual
'Removing and installing charge-air cooler'

2.8

Install bumper.  Workshop Manual
'Removing and installing rear bumper'

2.9

Install rear apron.  Workshop Manual
'Removing and installing rear apron'

The following work steps concern Scope 3.
Figure 7

3.1

Remove rear spoiler completely. 
Workshop Manual 'Removing and installing rear spoiler'

3.2

Install lid lock (tightening torque 9.7 NM (7.2 ftlb.)), rubber sleeves (6x), holders for lower
part of spoiler (2x), speed nuts (2x), and wiring harness to new spoiler drive unit.

3.3

Unpin 14-pin connector housing  Figure 8 from the removed standard spoiler plate.
Important: Do not damage the 14-pin