GLOBAL SAFETY FIELD INVESTIGATIONS
DCS6713
URGENT - DISTRIBUTE IMMEDIATELY
Date:

November 9, 2023

Subject: N232425900 - Customer Satisfaction Program
Service 4WD Message
Models: 2023 Chevrolet Silverado 1500
2023 GMC Sierra 1500

To:

All General Motors Dealers

General Motors is releasing Customer Satisfaction Program N232425900
today. The total number of U.S. vehicles involved is approximately 138.
Please see the attached bulletin for details.
Customer Letter Mailing
The customer letter mailing will begin in November 2023.
Global Warranty Management (GWM)
The Required Field Action section on the Investigate Vehicle History (IVH) screen will
be updated November 9, 2023. A list of vehicles in dealer inventory is attached to this
message.
END OF MESSAGE
GLOBAL SAFETY FIELD INVESTIGATIONS

Customer Satisfaction Program
N232425900 Service 4WD Message
Release Date:
Attention:

November 2023

Revision:

00

This program is in effect until November 30, 2025.

Make
Chevrolet
GMC

Model
Silverado 1500
Sierra 1500

Model Year
From
To
2023

RPO

Description

2023

Involved vehicles are marked “Open” on the Investigate Vehicle History screen in GM Global Warranty Management
system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections
and/or repairs.
Condition
Correction

Certain 2023 model year Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles, may have a condition
in which the Electronic Park Brake does not auto release with Service 4WD message.
Dealers are to reprogram the Transfer Case Control Module.

Parts
No parts are required for this repair.
Warranty Information
Labor
Operation
9106894*
9106895*
Important:

Description
Verified Module Software or Calibration Level: Module Is
Programmed with Same Level Software or Calibration
Transfer Case Control Module Reprogramming with SPS

Labor
Time
0.2

Trans.
Type

Net
Item

ZFAT

N/A

0.3

* To avoid warranty transaction rejections, carefully read and follow the instructions below:

6125814
• The Warranty Claim Code from the programming event must be accurately entered in the “Warranty Claim
Code” field of the transaction.
•

When more than one Warranty Claim Code is generated for a programming event, it is required to document all
Warranty Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the
“Warranty Claim Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter
the FINAL code provided by SPS2.

Copyright 2023 General Motors. All Rights Reserved.

Page 1 of 6

Customer Satisfaction Program
N232425900 Service 4WD Message
Warranty Claim Code Information Retrieval

6125774
If the Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS2 system as
follows:
1.
2.
3.
4.

Open TLC on the computer used to program the vehicle.
Select and start SPS2.
Select Settings (1).
Select the Warranty Claim Code tab (2).

The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is
retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code
field.
Service Procedure
Note: Carefully read and follow the instructions below.

•

Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector.
If there is an interruption during programming, programming failure or control module damage may occur.

•

Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will
interrupt programming. Install a GM Authorized Programming Support Tool to maintain system voltage. Refer to
www.gmdesolutions.com for further information. If not available, connect a fully charged 12 V jumper or booster
pack disconnected from the AC voltage supply. DO NOT connect a battery charger.

•

Follow the on-screen prompts regarding ignition power mode, but ensure that anything that drains excessive power
(exterior lights, HVAC blower motor, etc) is off.

•

Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M)
system status indicators to NO.

Important: The service technician always needs to verify that the VIN displayed in the TLC left side drop down menu and
the top center window match the VIN plate of the vehicle to be programmed prior to using Service Programming System
2 (SPS2) for programming or reprogramming a module.

•

For the TLC application, service technicians need to always ensure that the power mode (ignition) is “ON” before
reading the VIN from the vehicle’s VIN master module and that they do not select a VIN that is already in the TLC
application memory from a previous vehicle.

•

If the VIN that shows up in the TLC top center window after correctly reading the VIN from the vehicle does not match
the VIN plate of the vehicle, manually type in the VIN characters from the vehicle VIN plate into the TLC top center
window and use these for programming or reprogramming the subject module with the correct vehicle VIN and
software and/or calibrations.
Page 2 of 6

Customer Satisfaction Program
N232425900 Service 4WD Message
•

The Engine Control Module (ECM) is the master module (for VIP vehicles) that TLC reads to determine the VIN of
the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the ECM also needs
to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate.

•

The Body Control Module (BCM) is the master module (for GEM vehicles) that TLC reads to determine the VIN of
the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the BCM also needs
to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate.

Caution: Be sure the VIN selected in the drop down menu (1) is the same as the vehicle connected (2) before beginning
programming.

5743643
Important: If the vehicle VIN DOES NOT match, the message below will be shown.

5877000

5644477
Important: Techline Connect screens shown above.

Page 3 of 6

Customer Satisfaction Program
N232425900 Service 4WD Message
Important: If the same calibration/software warning is noted on the TLC Summary screen, select OK and follow
screen instructions. After a successful programming event, the WCC is located in the Service Programming System
dialogue box of the SPS Summary screen. No further action is required. Refer to the Warranty section of the bulletin.
1.

Reprogram the transfer case control module. Refer to K69 Transfer Case Control Module: Programming and Setup
in SI.

5644478
Note: The screenshot above is an example of module programming and may not be indicative of the specific module
that is being programmed. Module selection and VIN information have been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the
Warranty Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the
WCC on the screen.
2.

Record SPS Warranty Claim Code on job card for warranty transaction submission.

Dealer Responsibility
All new, used, GM Certified Pre-Owned (CPO), courtesy transportation vehicles, dealer shuttle vehicles, CarBravo, etc.
in dealers' possession and subject to this field action must be held and inspected/repaired per the service procedure of
this bulletin before customers take possession of these vehicles. Involved vehicles must be held and not delivered to
customers, dealer-traded, released to auction, used for demonstration, or any other purpose.
All GM Certified Pre-Owned (CPO) vehicles currently in the dealers’ inventory within the SHIFT Digital system will be
de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting an accepted/paid
warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified for sale within
the SHIFT Digital system, or once again be used in the Courtesy Transportation Program.
Dealers are to service all vehicles subject to this program at no charge to customers, regardless of mileage, age of vehicle,
or ownership, through November 30, 2025. Customers who have recently purchased vehicles sold from your vehicle
inventory, and for which there is no customer information indicated on the involved vehicle listing, are to be contacted by
the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this
bulletin. A copy of the customer letter is provided in this bulletin for your use in contacting customers. Program followup cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this program enters your vehicle inventory or is in your facility for service
through November 30, 2025, you must take the steps necessary to be sure the program correction has been made before
selling or releasing the vehicle.
Dealer Reports – For USA & Export
For dealers with involved vehicles, a listing has been prepared and will be available through GM GlobalConnect Maxis
Field Action Reports or sent directly to export dealers. The Inventory tab of the dealer reports will contain VINs that
apply to this field action. This information is intended to assist dealers with the PROMPT COMPLETION of these
vehicles. The Customer In-Service tab will contain customer names and addresses from Motor Vehicle Registration
Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete
this field action may be a violation of law in several states.

Page 4 of 6

Customer Satisfaction Program
N232425900 Service 4WD Message
Courtesy Transportation – For USA & Canada
Courtesy transportation is available for customers whose vehicles are involved in a product program and still within the
warranty coverage period. See General Motors Service Policies and Procedures Manual for courtesy transportation
program details.
Customer Notification
USA & Canada - General Motors will notify customers of this program on their vehicle (see copy of customer letter included
with this bulletin).
Export - Letters will be sent to known owners of record located within areas covered by the US National Traffic and Motor
Vehicle Safety Act. For owners outside these areas, dealers should notify customers using the attached sample letter.

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.

We Support
Voluntary Technician
Certification

Page 5 of 6

Customer Satisfaction Program
N232425900 Service 4WD Message
November 2023
This notice applies to your vehicle, VIN: ________________________________
Dear General Motors Customer:
We have learned that your 2023 model year Chevrolet Silverado 1500 or GMC Sierra 1500 may have a condition in
which the Electronic Park Brake does not auto release with Service 4WD message.
Your satisfaction with your Silverado 1500 or Sierra 1500 is very important to us, so we are announcing a program to
prevent this condition or, if it has occurred, to fix it.
What We Will Do: Your GM dealer will reprogram the Transfer Case Control Module. This service will be performed
for you at no charge until November 30, 2025. After that, any applicable warranty will apply.
What You Should Do: To limit any possible inconvenience, we recommend that you contact your dealer as soon as
possible to schedule an appointment for this repair.
If you have any questions or concerns that your dealer is unable to resolve, please contact the appropriate Customer
Assistance Center at the number listed below.
For the hearing or speech impaired, please contact our Customer Assistance Center using the Telecommunication
Relay Service by dialing 711 then providing the appropriate Customer Assistance Center number for your vehicle.
Division
Chevrolet
GMC
Puerto Rico – English
Puerto Rico – Español
Virgin Islands

Number
1-800-222-1020
1-800-462-8782
1-866-467-9700
1-866-467-9700
1-866-467-9700

Text Telephones (TTY)
711 / 1-800-833-2438
711 / 1-800-833-2438

We truly appreciate you taking the time to update your vehicle as we know your time is valuable. We want you to know
that we will do our best, throughout your ownership experience, to ensure that your GM vehicle provides you many
miles of enjoyable driving.
Neelie O’Connor
Global Executive Director
Customer Experience Operations

N232425900

Page 6 of 6