BULLETIN NOTES
APPLICABLE MODEL(S)/VINS
2024 CX-90 with Driver Personalization System
DESCRIPTION
This Service Alert provides additional guidance about operation and procedure of the Driver Personalization System from
the start of driver recognition to the end of the driving position restoration.
Timing (start/completion/discontinuing) of driver recognition and a driving position restoration:

Page 1 of 5

10/17/2023 12:06 PM tlawrenc

(1) The driver's-side door closes.
(A) The driver recognition operation starts.
When closing the driver's door, the driver recognition starts to detect the driver's face.
NOTE: The status of the driver recognition cannot be displayed on the center display.
(B) The driver recognition is completed (a registered driver/a guest driver).
Once the system identifies whether the driver is a registered one or not, the driver recognition is completed. When
the driver recognition is completed, the recognition result is displayed on the center display.
1. If the driver is a guest driver, the recognition result is displayed on the center display as in the following image.

2. Registered Driver
2-a. If the driver is the same person as last time, the recognition result is displayed at the bottom of the center
display.

2-b. If the driver is NOT the same person as last time, the recognition result is displayed on the center display as
in the following image.

(C) The driving position restoration starts

Page 2 of 5

10/17/2023 12:06 PM tlawrenc

When the system identifies the driver as the registered one, the driving position can be restored.
• If the driver is identified as the same one as last time, the driving position is restored when the recognition
is completed.
• If the driver is NOT identified as the same one as last time, "Welcome, *** " is displayed on the center
display. The driving position is restored, after selecting "OK" in the center display with the commander
knob.
• If the driver is identified as a guest, the driving position is not changed.
NOTE:
• When the driver switches with another, the shift amount of the driving position (especially the seat and the
steering wheel) may be large.
• For the driver's safety, the driving position will be restored only when the driver selects "OK" in the center
display.
(D) The driving position restoration is completed
When the driving position restoration is completed, the notification sound is activated (pop sound).
(X) The driver recognition is discontinued
Driver recognition is discontinued when turning the ignition ON or shifting into other than P-range during driver
recognition.
NOTE: If driver recognition is discontinued, the driver is always identified as a guest and the system operates for
a guest driver. The center display shows that the driver is recognized as a guest driver.
(Y) The driver recognition is timed out
1. If no face is detected because the driver’s face is NOT looking forward, the system will continue the face detect
operation for 10 seconds.
2. If still no face is detected, the driver recognition will be timed out.
3. After the driver's face is detected and if the driver recognition cannot be completed within 30 seconds, it will be
timed out.
NOTE: When driver recognition is timed out, the recognition result is not displayed, and the driver switching
operation is not activated and the driving position does not change.
(Z) The driving position restoration is discontinued
If performing the following action during the driving position restoration, the restoration operation is discontinued
and the refusal sound is activated (beep sound).
• Shifting into any position other than Park.
• Operating any switches related to driving positions.
Seat position memory switch
Door lock/unlock with the advanced keyless entry function
Steering wheel electric adjustment switch
Power seat adjustment manual switches
Outside mirror adjustment switches
Performing active driving display setting with Mazda Connect
○
○
○
○
○
○

NOTE: If performing cranking during the driving position restoration, the restoration operation is suspended for a
Page 3 of 5

10/17/2023 12:06 PM tlawrenc

while and then resumed.
Frequently Asked Question (FAQs):
1

Why is the driver recognized as a guest every time?
The driver recognition may be interrupted. Avoid any operations (including cranking/IG-ON etc.) until the driver
recognition is completed.
Due to accessories and/or angle of the face, the driver's face may not be recognized. The following measures
may improve the driver recognition.
• Try the same appearance and the face angle as the driver recognition.
• Redo the driver recognition with Mazda Connect (Settings > Driver Personalization System > Edit Driver
Profile > Redo Driver Recognition)

Page 4 of 5

10/17/2023 12:06 PM tlawrenc

• Two appearances per a driver can be registered. Add/Redo alternative appearance recognition with Mazda
Connect (Settings > Driver Personalization System > Edit Driver Profile > Add Alternate Appearance /Redo
Alternate Appearance).
NOTE: When doing/redoing the appearance recognition, show natural appearance (opening the eyes, closing the
mouth etc.).
2

Why is the Driving Position NOT restored?
• If the driver is recognized as a guest, the driving position restoration is NOT activated.
• If the driver is switched with another before the driver recognition is completed, the driving position
restoration is NOT activated immediately. In this case, the welcome message is shown when the driver
recognition is completed and the driving position restoration will start after selecting "OK" on the center
display with the commander knob.

• If there are obstacles on the movement line of the seat or misalignment of the memory seat motor, the
driving position may NOT be restored properly. Refer to SA-043/23 - AUTOMATIC SEAT POSITION
ADJUSTMENT IS INTERRUPTED.
3

Why does it take time to display the result of the driver recognition?
When the vehicle wakes up by unlocking the door etc. during sleep mode, it takes time to start the vehicle system
and to begin the face detection. That may cause a few seconds of a delay in displaying the recognition result.

4

When starting the vehicle, why is the View Monitor displayed on the instrument cluster before the result
of the driver recognition?
If "Display Priority View at Start Up" is set "Enable", View Monitor is displayed preferentially when the vehicle is
started. Pressing "360° View Monitor switch" closes the View Monitor, and displays the result of the driver
recognition.
Page 5 of 5

10/17/2023 12:06 PM tlawrenc