Technical product information
Topic
Market
area

New Continental GT and GTC - Window drop glass operation
Australia E04 Bentley rest Asia and Australia (6E04),China 796 VW Import Comp. Ltd (Vico), Beijing (6796),Germany E02 Bentley
rest Europe (6E02),Japan E03 Bentley Japan (6E03),Korea, (South) E08 Bentley South Korea (6E08),United Arab Emirates E06
Bentley Middle East and Africa (6E06),United Kingdom E01 Bentley UK (6E01),United States E05 Bentley USA and rest America
(6E05)
Bentley

Brand
Transaction
2070497/3
No.
Level
EH
Status
Approval
Release
date
Event memory entries

Diagnostic address
0052 - Passenger's door electronics
00BB - Rear drivers side door electronics
00BC - Rear passenger side door electronics
0042 - Driver's door electronics

Event memory entry
Fault type Fault status
B148754: Window regulator motor no basic setting
Intermittent
B148754: Window regulator motor no basic setting
Intermittent
B148754: Window regulator motor no basic setting
Intermittent
B148754: Window regulator motor no basic setting
Intermittent

New customer code
Object of complaint
body fixtures and fittings -> window opening/closing, window heating -> window return at
door-closing
body fixtures and fittings -> window opening/closing, window heating -> window drop at dooropening
body fixtures and fittings -> window opening/closing, window heating -> window drop at dooropening
body fixtures and fittings -> window opening/closing, window heating -> window drop at dooropening
body fixtures and fittings -> window opening/closing, window heating -> window return at
door-closing
body fixtures and fittings -> window opening/closing, window heating -> window return at
door-closing
body fixtures and fittings -> window opening/closing, window heating -> window return at
door-closing
body fixtures and fittings -> window opening/closing, window heating -> window drop at dooropening

Vehicle data
New Continental GT and GTC
Sales types
Type
3S3*
3S3*
3S3*
3S3*
3S3*
3S3*
3S4*
3S4*
3S4*
3S4*
3S4*

MY
2018
2019
2020
2021
2022
2023
2019
2020
2021
2022
2023

INTERNAL

Brand Designation Engine code Gearbox code Final drive code
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*

Complaint type
functionality -> without function / defect
functionality -> defective function
sequence
functionality -> defective function
sequence
functionality -> defective function
sequence

Position
rear
right
front left
rear left
front
right

functionality -> without function / defect

front left

functionality -> without function / defect

rear left

functionality -> without function / defect
functionality -> defective function
sequence

front
right
rear
right

Documents
Document name
master.xml
newglasssetgt.pdf
newglasssetgtc.pdf
retailerglassresetproceduregtandgtc.pdf

INTERNAL

Technical product information
New Continental GT and GTC - Window drop glass operation

Transaction No.: 2070497/3

Customer statement / workshop findings
•

Incorrect operation/function of the front and/or rear window drop glass

•

Front and/or rear drop glass fails to open/close or attempts to close and re-opens once contact has been made between the glass and
applicable seal

•

DTC for window regulator motor no basic setting B148754 evident within any of the 4 window control modules (diagnostic address 42, 52,
BB and BC) for loss of basic settings

Technical background
IMPORTANT NOTE: Aftermarket window tinting can affect the operation of the windows, please advise customers the onward
instructions should not be applied until all aftermarket tinting has been removed
TPI revision history
CAUTION
The operative must always ensure the latest version of this TPI is obtained from Elsa pro using the applicable VIN as TPI versions can change
without notice
TPI 2070497/2
•

The attached PDF document has been revised relating to the adjuster screw process (page 6) and the bump stop checks (page 9)

•

The TPI has also been changed to include an improved navigational path to the videos (x3) in step 11 of the attached PDF document

TPI 2070497/3
•

A second software update has been added within the Measure section, the software update relates to the rear control modules only and
eliminates the short drop open function of the rear windows

The operative must first check Reference Table 1 and Reference Table 2 within Section 1 of the Measure section to confirm the software levels
of the door control units
Should the software levels not be at the latest level, the operative must conduct the applicable software installation instructions
•

Once the software is successfully updated as detailed within Reference Table 1 and Reference Table 2 or the software versions were
already at the correct level, the operative must then conduct the software update instructions within Section 2, once the required software
updates have been completed (within section 1 and 2) the operative must then conduct Section 3

Production change
The Bentley continuous improvement policy has been implemented within the manufacturing process, the required improvements have been
utilised within this TPI

Measure
VERY IMPORTANT: To eliminate a repeat repair the instructions within the Measure section and attached PDF instructions
must be conducted on the front and rear drop door glass - left and right hand side to completion
1) Referring to Rep.Gr 27 - Carry out a 12 Volt battery test "WARRANTY TEST" or "ORIG. VW-BATT. TEST"
NOTICE
VERY IMPORTANT: Save an image of the battery printout as this will be required to be attached to a new or existing DISS query, should any
issues be evident with the 12 volt battery/system this should be rectified before proceeding any further
– In the event there was an issue with the 12 volt battery and the drop door glass issue is now resolved no further action is required
However
In the event the drop glass issue is still evident after the confirming the 12 volt battery is to specification the operative should
conduct the onward instructions to completion

INTERNAL

Before proceeding with the onward instructions the following window closing time results are required to be attached to a
new or existing DISS query
VERY IMPORTANT: Do not proceed with the time measurement request instructions unless the battery is confirmed to be
within specification (battery test) a 12 volt battery charger must also be installed as per Rep.Gr 27
Passenger side front and rear
Hint: The window closing time should be 4 seconds
•

Measure the time (in seconds) it takes to close the front and rear windows from fully open to the fully closed position

•

Record the time

Passenger side front = seconds
Passenger side rear = seconds
Comments

Driver side front and rear
Hint: The window closing time should be 4 seconds
•

Measure the time (in seconds) it takes to close the front and rear windows from fully open to the fully closed position

Driver side front =
Driver side rear =
Comments

seconds
seconds

Section 1 - Door control module identification/update instructions
NOTICE
The control modules should all be at ‘D’ suffix or all at ‘J’ suffix, replacement of ‘D’ level control modules to ‘J’ level does not fix the problem,
replacement of control modules should not be conducted without permission via DISS, in the event the control modules were replaced without
permission all applicable Warranty claims will be cancelled
– In the event that a control module is suspected as being faulty the operative must request permission via DISS before replacing any parts
– Do not under any circumstances combine ‘D’ suffix control modules with ‘J’ suffix parts all four control modules must all have the same suffix
2) Check and if necessary update the applicable door control modules as follows:
CAUTION
Should the control modules NOT be at the latest levels as shown in Reference table 1 and 2 please conduct the two separate software
updates within Section 1 and Section 2 to completion before proceeding with Section 3
However
In the event the software levels are to specification as shown in Reference table 1 and 2 please only conduct the software
update within Section 2 before proceeding with Section 3

INTERNAL

D suffix control modules - Reference table 1
Door control module

Part number

Software version

Target data container

0042 – Drivers door

4M1.959.953.D

0189

V03.935.344.TP

0052 – Passenger door

4M1.959.952.D

0189

V03.935.344.TQ

00BB – Rear driver’s door

4M1.959.955.D

0189

V03.935.344.TR

00BC – Rear passenger door 4M1.959.955.D

0189

V03.935.344.TS

J suffix control modules - Reference table 2
Door control module

Part number

Software version

Target data container

0042 – Drivers door

4M1.959.953.J

0430

V03.935.349.CM

0052 – Passenger door

4M1.959.952.J

0430

V03.935.349.CN

00BB – Rear driver’s door

4M1.959.955.J

0430

V03.935.349.CP

00BC – Rear passenger door 4M1.959.955.J

0430

V03.935.349.CQ

Software update - Front and rear door control modules
•

The closed-circuit voltage of the vehicle must be at least 12.5 V during the update. Connect a suitable battery charger
to the vehicle. For further information refer to the Repair manual

•

During the update switch off all unnecessary consumers (ventilation, seat heater, interior illumination etc) ensure the
main light switch is set to ‘off’ and leave the driver’s door open

•

Because of the highest transmission stability you MUST use the diagnosis interface VAS 6154 (WiFi diagnostic tool)
ONLY in USB operation or the cable-connected VAS 5055 for the reprogramming (updating) of control modules. If these
units are not available, the diagnosis interface VAS 5054 (A) can also be used in USB mode

•

Do Not under any circumstances use a Bluetooth connection to conduct the reprogramming (updating) of any control
modules

3) Referring to Figure 1 - Within the Special functions tab - Select SVM - Code Input (Point A)
• Select Perform test (Point B)

Figure 1
4) Referring to Figure 2 - Enter SVM code 370FTM01

INTERNAL

Figure 2
- When prompted enter your global user ID and password
- Follow all on screen prompts to continue through the procedure, the identification data will be transferred
5) The required control modules will be automatically updated one by one, starting with 0042 – Door electronics Drivers side (Figure 3)

Figure 3
6) Once the update is complete the summary screen will be shown in Figure 4, this confirms completion of the required updates

Figure 4
7) Recheck the Door control module versions against the Reference tables 1 and 2 (depending on Part number/Software version)

INTERNAL

Section 2 - Software update - Rear door control modules 00BB and 00BC (short drop function elimination)

The software update eliminates the rear window short drop function
8) Referring to Figure 5 - Within the Special functions tab - Select SVM - Code Input (Point A)
• Select Perform test (Point B)

Figure 5
9) Referring to Figure 6 - Enter the SVM code 370WAD01