Technical Bulletin
Model(s)

Year

Jetta Hybrid

2013

Engine Code

Trans. Code

VIN Range From

VIN Range To

1.4L

7spd DSG /
0CG (DQ200)

AJ_DM000038

AJ_DM290930

(CNLA)

Condition
01 13 15 June 04, 2013 2033979
Update Programming, MIL ON, Sporadic DTCs Stored in ECM or Power Electronics Fault Memory
One or more of the following fault codes may be stored in the ECM Fault Memory (Address Word 01):

DTC

Description

P0087

Fuel Rail/System Pressure - Too Low

P119A

Fuel pressure sensor - G247 Malfunction

P164B

Oil Pressure Switch Malfunction

P30A1

Engine start interruptions permissible number
exceeded

One or more of the following fault codes may be stored in the Power Electronics Fault Memory (Address Word
51):

DTC

Description

P0A40

Drive Motor "A" Position Sensor Circuit
Range/Performance

Note:
DO NOT diagnose or replace any related components before performing the update function as explained in this
bulletin.

Page 1 of 5 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Technical Background
Updated programming of the ECM and Power Electronics software has been released to improve the monitoring
strategies of various systems.

Production Solution
Improved software introduced in production.

Service
Update-Programming Procedure:
Tip:
To Update-Programming using SVM, review and follow instructions in Technical Bulletin Instance 2014603
“Software Version Management”.
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A
warranty claim may not be reimbursed if there is no confirmation response to support the claim.

Note:
Prior to launching VAS-PC application and starting control module update process, confirm tester screen saver
and power settings in accordance with Special Tools and Equipment - Service Information Circular # VSE-08-18.
Failure to do so may result in the tester entering power save mode during data transfer, and subsequent control
module failure.
When using a VAS 6150/5051B or VAS 5052A tester in conjunction with a VAS 5054A wireless transmitter head
for a flash procedure, please connect a USB cable between the transmitter head and the tester. Failure to do so
may lead to errors during the flash procedure.
• Update the Engine Control Module using the SVM Unit code as listed in the table below:

Model

Engine

Old Software
Part No.

Old Software New Software New Software
Version
Part No.
Version (or
higher)

SVM Unit
Code

1.4L
Jetta Hybrid

04E906023

All

04E906023

5631

384C

CNLA
Page 2 of 5 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
• Update the Power Electronics Control Module using the SVM Unit code as listed in the table below:

Model

Engine

Old Software
Part No.

Old Software New Software New Software
Version
Part No.
Version (or
higher)

SVM Unit
Code

1.4L
Jetta Hybrid

5C0907080C

All

5C0907080E

0535

384C

CNLA

The procedure can be found in GFF under Functions/ Component Selection, Software Version Management,
Adapting Software.

WARNING:
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may
result if contact is made with spinning fan blades.
Keep hands and all objects away from Radiator Fan(s) during Update Process!

Tip:
The SVM Process must be completed in its entirety so the database receives the update confirmation response. A
warranty claim may not be reimbursed if there is no confirmation response to support the claim or action is carried
out that is not explicitly stated in the Technical Bulletin.
Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM
Technical Bulletin Instance 2014603.

Page 3 of 5 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Warranty
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
1)
Procedures Manual
Model(s)

Year(s)

Jetta Hybrid

2013

Eng. Code(s)

Trans.
Code(s)

1.4L

7spd DSG

(CNLA)

0CG/DQ200

VIN Range From

VIN Range To

AJ_DM000038

AJ_DM290930

SAGA Coding
Claim Type:

Use applicable Claim Type

1)

Damage
Service Number:

HST

Damage Location (Depends on
Service No.)

--

Use applicable when indicated in
ElsaWeb (L/R)

Code
2470

0039

Parts Manufacturer

Jetta Hybrid

Labor Operation : Charge Battery

3)

27068950 = 10 TU

Labor Operation : Update Programming

3)

24702599 = 50 TU

Causal Part: Select Labor Operation

24702599
Diagnostic Time

3ME

2)

4)

GFF Time expenditure

01500000 = 20 TU max.

YES

Road Test

01210002 01210004

NO

Technical Diagnosis

0132xxxx = 00 TU max.

NO

Claim Comment: Input “As per Technical Bulletin 2033979” in comment section of Warranty Claim.
1)

Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policy Procedures Manual.
Page 4 of 5 plus attachment

© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

Technical Bulletin
Required Parts and Tools
No Special Parts required.

Tool Description

Tool No:

Midtronics Battery Tester/Charger

InCharge 940 (INC-940)

VAS Diagnostic Tool

VAS 5051B, VAS 5052A, VAS 6150/X & VAS 6160/VPC with:
VAS-PC Base V19.01.01 and current version Brand
disc
ODIS Service V1.1.3 or higher

Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.

Page 5 of 5 plus attachment
© 2013 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.

OWNER INFORMATION ABOUT CONTROL MODULE TUNING*
ACKNOWLEDGEMENT AND AUTHORIZATION FOR
REPROGRAMMING (REFLASHING) OF CONTROL MODULE(S)
*) “TUNING” is described as the addition of or modification of any component which causes a
Volkswagen vehicle to perform outside the normal parameters and specifications approved by
Volkswagen Group of America / Volkswagen Group Canada.

Date:
Dealer Number:
Vehicle Identification Number:
Repair Order Number:
Dealer stamp

I

, owner or driver of the above identified Volkswagen, confirm:

- “Tuning” as described above (especially power increasing modifications) has NOT been
performed on my vehicle.
- “Tuning” as described above has been performed on my vehicle and the following components
were modified or installed:

TUNING was performed by (Please provide Company name and telephone number, if you wish us
to contact them):

I understand that if my Control Module is determined to have been tuned, any damage caused by
the tuning of the Control Module (including adverse emissions consequences) will not be covered
by VWGoA / VGC warranties.
I am permitting an authorized Volkswagen Dealer to reflash (update) my Control Module, and by
doing so, I understand that this process will automatically overwrite (destroy) and permanently
delete any tuning program that was previously installed on the Control Module of my Volkswagen
vehicle.
By signing below, I fully acknowledge and understand that the tuning program will not be restored
and VWGoA / VGC, will not be liable in any way for the loss of tuning data.

Signature of Customer
E 2013 Volkswagen Group of America Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printi ng and is subject to the copyright and other intellectual
property rights of VGoA / VGCA Inc., its affiliated companies and its licensors. All rights are reserved to ma ke changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitte d in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or rep osted to other sites, without the prior expressed written permission of the publisher .