ATTENTION:
GENERAL MANAGER

q

PARTS MANAGER

q

CLAIMS PERSONNEL

q

IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.

SERVICE MANAGER

q

© 2023 Subaru of America, Inc. All rights reserved.

SERVICE BULLETIN
APPLICABILITY:

2014-19 Legacy & Outback

NUMBER: 07-223-23R

SUBJECT: New Genuine Subaru Replacement Battery
(SOA821B950)

DATE: 07/11/23
REVISED: 07/13/23

INTRODUCTION:
This bulletin announces the availability of a new Genuine Subaru Replacement Battery introduced
to replace the current battery (SOA821B400). The new battery (SOA821B950) has a higher
capacity and is slightly different in size. When replacing an originally equipped battery with the new
SOA821B950 Genuine Subaru Replacement Battery, additional parts and slight modifications will
be required to ensure proper positioning and security. Please refer to the work procedures outlined
below.
PART INFORMATION:
REMINDER: Always order the most up-to-date replacement parts based on the specific VIN being
repaired.
Part Description

Part Number

Part Description

Part Number

BATTERY

SOA821B950

BATTERY COVER

82123AN000

SPACER (3.6L ONLY)

82190AL000

NOTE: The parts listed above must be ordered
through PRIME.
SERVICE PROCEDURE / INFORMATION:
Please review the battery identification, charging, and testing information provided in Service
Bulletin 07-178-21 before performing any battery testing and/or charging. ALWAYS confirm
Midtronics equipment has the latest software available.
NOTE: The original battery holder, battery tray, and holding rods are to be reused.
STEP 1: Remove the battery as per the applicable Service Manual: Engine > STARTING/
CHARGING SYSTEMS > Battery > Removal
CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.

Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.

Continued...
Bulletin Number: 07-223-23R; Revised: 07/13/23

Page 1 of 3

STEP 2: Install the NEW battery cover (82423AN000) to the replacement battery. Confirm the
bottom of the cover is aligned flush with the bottom of the battery.

STEP 3: Battery Installation
A. 2.5L Equipped Models ONLY: Install the battery as per the applicable Service Manual:
Engine > STARTING/CHARGING SYSTEMS > Battery > Installation. Proceed to Step 6.
B. 3.6L Equipped Models ONLY: Install the battery with spacer (82190AL000) to the rear
side of the battery tray. The spacer must be installed with the flat side against the battery
and the notched portion facing the bottom of the battery tray. See the images below.

Install the battery as per the applicable Service Manual: Engine > STARTING/CHARGING
SYSTEMS > Battery > Installation. Proceed to Step 4.
IMPORTANT NOTE: ALWAYS confirm the spacer fitment is flush when securing the battery with
the hold down and hold down rods.

Continued...
Bulletin Number: 07-223-23R; Revised: 07/13/23

Page 2 of 3

STEP 4: Install the battery holder and holding rods onto the battery.
A. Torque the two holding rod mounting nuts to 7.5 N·m (5.5 ft-lbs. or 66 inch-lbs.).
B. Torque the positive terminal to 6 N·m (4.4 ft-lbs. or 53 inch-lbs.).
C. Torque the negative terminal to 7.5 Nm (5.5 ft.-lbs. or 66 inch-lbs.).
D. If the battery sensor is removed or disconnected torque to 6 Nm (4.4 ft.-lbs. or 53 inchlbs.) while supporting the sensor with the other hand as outlined in the applicable Service
Manual under: STARTING/CHARGING SYSTEMS> Battery Sensor.
NOTE: Confirm the battery holder is center mounted with the battery cables secured and routed
correctly.
WARRANTY / CLAIM INFORMATION:
For vehicles within the Basic New Car Limited Warranty period, this repair may be submitted using
the following claim information:
Labor Description

Labor Operation #

Labor Time

Fail Code

STD FLOODED BATT TEST & REPL W/ ENHANCED
FLOODED BATT

A800-003

0.5

FFG-42

NOTE: A valid battery test code or an authorization with reason for leaking/cracked battery will be
required for Claim submission.
IMPORTANT REMINDERS:
•

SOA strongly discourages the printing and/or local storage of service information as previously
released information and electronic publications may be updated at any time.

•

Always check for any open recalls or campaigns anytime a vehicle is in for servicing.

•

Always refer to STIS for the latest service information before performing any repairs.

Bulletin Number: 07-223-23R; Revised: 07/13/23

Page 3 of 3