Classification:

Reference:

DA22-008B

Date:

NTB23-011B

June 22, 2023

"FORWARD DRIVING AIDS BLOCKED" MESSAGE ON
INSTRUMENT PANEL DURING SNOWY/ICY DRIVE WEATHER
CONDITIONS, WITH DTC C2582-97 STORED IN LASER/RADAR
CONTROL UNIT
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

APPLIED VEHICLES:

2021-2023 Rogue (T33)

IF YOU CONFIRM
The message “Forward Driving Aids Blocked” is displayed on the Instrument Panel during
snowy/icy drive weather conditions, with DTC C2582-97 (Distance Sensor) stored in the
LASER/RADAR control unit,
AND
Salt residue or snow/ice is present between the inside surface of the Front Bumper Fascia
and front surface of the Distance Sensor.
HINT: Refer to Flow Chart on page 2.
o This bulletin applies only if the customer experienced the “Forward Driving Aids
Blocked” message during snowy/icy drive weather conditions.
o This bulletin does not apply if any other type of contamination (e.g., dirt, debris,
or rain) is on the Distance Sensor surface. In that instance, refer to NTB019-033
and the ESM for further diagnostic information. Do not apply the Service Kit in
PARTS INFORMATION.
ACTION
Install the Distance Sensor Bracket & Grill Tape Service Kit following the SERVICE
PROCEDURE starting on page 3.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/8

Flow Chart

“Forward Driving Aids Blocked”
message displayed and DTC
C2582-97 stored as PAST?

No

Yes

Customer has confirmed the
message displays during active
snowy/icy drive weather conditions?

No

Yes

Inspect the Distance Sensor face.

Salt residue or
snow/ice present on
the sensor face.

Debris or dirt
present on the sensor
face.

Proceed to step 1 on
page 3 of this bulletin.

Refer to NTB19-033
and the ESM for
further diagnostic
information.

2/8

NTB23-011B

SERVICE PROCEDURE

1.

Remove the Front Grille.


Refer to the ESM: BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY >
EXTERIOR > REMOVAL AND INSTALLATION > FRONT GRILLE > Removal
and Installation

2.

Wipe off salt residue/snow/ice from the surfaces of the Distance Sensor and the back
side of the Nissan emblem.

3.

Snap the Distance Sensor Bracket (Figure 1) onto the Distance Sensor.


See PARTS INFORMATION.

Distance Sensor
Bracket

Distance Sensor

Figure 1

3/8

NTB23-011B

Refer to steps 4-7 to attach two (2) Foam Seals (Figure 2) to the inside of the Nissan
emblem, on the Grille, to close the Grille spaces (Figure 3).
HINT: The Foam Seals are left and right, and are shown in Figure 2 on the sides and
orientation that they will be installed.

Driver (LH) side
Top of Grille

Rear of Nissan
emblem

Passenger (RH) side

Figure 2

Grille spaces
outlined in green
Figure 3

4/8

NTB23-011B

HINT: The left side is shown in the following Figures. The right side is similar.
4.

Remove the self-adhesive backing from the left side Foam Seal.


Install the Foam Seals one at a time.

Foam Seal backing
Figure 4
Foam Seal top

5.

Start attaching the Foam Seal at the
top of the Nissan emblem.
IMPORTANT: The top of both the left
and right Foam Seals must be
touching each other when installed.

Figure 5

6.

Continue attaching the foam as shown
in Figure 6 and Figure 7 on page 6.
HINT: Use the self-adhesive cut-outs
to help align the Foam Seal.
Self-adhesive cut-outs

Figure 6
5/8

NTB23-011B

Foam Seal notch



Foam Seal notch should be level
with the end of the last grille space.

Level with grille
space
Figure 7
7.

Refer to steps 4-6 on page 5 to install the right side Foam Seal.


Both Foam Seals must seal against each other at the top.

HINT: Figure 8 shows both Foam Seals installed.

Foam Seal tops

Figure 8
8.

Fold the tops of the two Foam Seals over together, as shown in Figure 9.

Figure 9

6/8

NTB23-011B

9.

Reinstall the Front Grille.


Refer to the ESM: BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY >
EXTERIOR > REMOVAL AND INSTALLATION > FRONT GRILLE > Removal
and Installation

Foam Seal sealed against
Distance Sensor Bracket

Figure 10

10.

With C-III plus, perform Erase All DTCs.

11.

Confirm that DTC C2582-97 no longer stores in the LASER/RADAR control unit.


If DTC C2582-97 continues to store in the LASER/RADAR control unit, refer to the
ESM for diagnostic information not supported by this bulletin.

7/8

NTB23-011B

PARTS INFORMATION
DESCRIPTION
BRKT-FR RADAR, MAIN
(Distance Sensor Bracket)
BRKT-FR RADAR, TAPE, RH
(Foam Seal)
BRKT-FR RADAR, TAPE, LH
(Foam Seal)

PART NUMBER

QUANTITY

285U2-6RF0A

1

285U2-6RF0C

1

285U2-6RF0D

1

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION

PFP

OP CODE

SYM

DIA

FRT

Install Bracket and Grille Tape Kit

(1)

BX8CAA

ZE

32

0.4

DESCRIPTION
Install Bracket and Grille Tape Kit With
AVM

PFP

OP CODE

SYM

DIA

FRT

(1)

BX8DAA

ZE

32

0.8

OR

(1)

Reference the electronic parts catalog and use the Distance Sensor (28437-*****) as
the Primary Failed Part (PFP).

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE

DESCRIPTION

January 26, 2023

NTB23-011

Original bulletin published

April 19, 2023

NTB23-011A

Republished to include NNA

June 22, 2023

NTB23-011B

Title and pages 1-3 revised

8/8

NTB23-011B