BULLETIN NOTES
This service alert supersedes the previously issued service alert listed below. The changes are noted in Red text.
Previous TSBs:

Date(s) Issued:

SA-009/23

05/24/23, 04/25/23, 03/28/23, 03/01/23 and 02/06/23

SA-017/22

12/13/22, 10/10/22, 08/25/22, 05/06/22, 04/04/22

SA-013/21

12/22/21, 10/13/21, 09/14/21, 05/11/21,
04/27/21, 03/15/21, 02/22/21, 02/08/21 and 02/02/2021

SA-031/20

12/09/20,11/30/20, 11/06/20, 10/28/20, 06/16/20, 06/05/20, 06/01/20, 05/18/20,
04/14/2020, 04/02/20, 03/11/20 and 02/27/20

APPLICABLE MODEL(S)/VINS:
2019-2023 Mazda3
2020-2023 CX-30
2021-2023 CX-5
2021-2023 CX-9
2022-2023 MX-30
2023 CX-50
2024 CX-90

DESCRIPTION
Some customers may complain about any of the following:
1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App
Connected Vehicle enrollment.
2. Remote function(s) inoperative.
•
•
•

Engine Start / Stop
Door Lock / Unlock
Lights ON / OFF

3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

Page 1 of 26

06/12/2023 11:31 AM tlawrenc

Index
•
•
•
•

MAZDA CONNECT Indication
Remote Engine Start Will Not Function
Remote Engine Start Function Will turn engine OFF
Deactivation Mode

MAZDA CONNECT Indication

Indication

Explanation

Mazda3, CX-30, CX-50, MX-30
Radio waves are not being received.
Move to a location with good reception.

Weak reception.

Good Receptioin

Strong reception.
Currently conducting an operation check of the
communication unit. If this condition continues, consult an
Authorized Mazda Dealer.
Currently conducting an operation check of the onboard
communication unit.
NOTE: Communication is not possible during this display.

CX-5, CX-50, CX-9, MX-30
Mazda3, CX-30 built July 1, 2021 and later

The communication function is temporarily disabled due to
infotainment system setting.

• Deactivation Mode
• Connected Service contract has ended
(Subscription expired)
Page 2 of 26

06/12/2023 11:31 AM tlawrenc

• TCU has not been initialized, go to SA-004/21
Vehicles built before July 1, 2021
Customer deactivated Connected Services (Opt-Out)
Vehicles built after July 1, 2021

• eMDCS Warranty Vehicle Inquiry will show
Campaign CSP04 Status Open

Connected Services disabled (box unchecked)

CX-5, CX-50, CX-9, MX-30
Mazda3, CX-30 built July 1, 2021 and later
Connected Services Disabled message
appears at engine start up

Enable Connected Services (box checked) to prevent
message appearing at engine start up.

Note: If customer Opted-Out ( CSP04), advise customer
to keep Connected Services box checked. The vehicle will
not transmit data.
Connected Vehicle Maintenance Mode

Connected Vehicle Maintenance Mode enabled.
Go to MGSS SERVICE CAUTIONS FOR VEHICLES
WITH TELEMATICS COMMUNICATION SYSTEM to
disable Maintenance Mode.
NOTE: Connected Vehicle Maintenance Mode is
unnecessary if the customers vehicle is in
Deactivation Mode .

Page 3 of 26

06/12/2023 11:31 AM tlawrenc

Remote Engine Start Will Not Function under the following conditions
Item
Condition
1

Vehicle battery voltage low

2

Automatic Transmission shift position except "P"

3

Vehicles equipped with manual transmission

4

Vehicle speed above 3 mi/h (5 km/h)

5

Brake pedal switch malfunction

6

Engine has been running by remote engine start function

7

Engine started by remote engine start more than 2 consecutive times while the vehicle is not driven.
The vehicle must be driven 1-mile or 24-hours must pass from the last successful Remote Engine
Start for the use count to reset.
2021 Mazda3, 2021 CX-30, CX-50, MX-30: Vehicle's electrical control area network (CAN) is in
"Sleep Mode"

8

or
9

A registered key is detected in the vehicle

10 Brake pedal switch detects brake application
Low fuel warning
11

12

Engine starts, then turns OFF due to abnormal high engine rpm detected. (Engine rotation over
3000 rpm continued for more than 0.2[s])

13

No engine rpm detected after sending engine start request. (Engine rotation 0 rpm continued for
more than 0.2[s])

14 When the CAN data signal for engine shut off is present (e.g.: door ajar signal)
15 After 10 second maximum cranking time
16

Burglar alarm status is "Alarm" and "Alarm stand by" (CAUTION - DO NOT enable, see TheftDeterrent System section in SA-012/20)

17 Room fuse blown/missing
18 Connected Vehicle Maintenance Mode enabled (Restricted Transmitting Mode in MDARS)

Page 4 of 26

06/12/2023 11:31 AM tlawrenc

19

Vehicle is parked (stored) for approximately 1 week or longer or in deep sleep mode.
Drive the vehicle for a few miles to recover.
DTC Stored

20

21 Aftermarket Remote Engine Start accessory installed.
Mazda Remote Engine Start (BCKA-V7-620) accessory installed (No MyMazda app remote engine
start function).
22 Mazda Remote Engine Start (RES) Removal
a. Remove the Mazda Remote Engine Start (RES) accessory module.
b. Deactivate and activate Advanced Key(s). Refer to MGSS IMMOBILIZER SYSTEMRELATED PARTS PROGRAMMING [(US)]
23

First remote control attempt fails, second attempt works fine.
Go to TSB 16-002/20.

24 CSP04 Status Open
Remote Engine Start Function Will turn engine OFF under the following conditions
Item
Condition
1

Vehicle door(s) opened

2

Vehicle trunk opened

3

Vehicle hood opened

4

Ignition switch push button "ON" detected

5

Remote engine STOP request

6

Brake pedal switch detects brake application

7

DTC Stored

8

Engine will stop running automatically after 15 minutes for safety, security and emissions.

Page 5 of 26

06/12/2023 11:31 AM tlawrenc

Deactivation Mode
Some new owners may chose not to enroll into Connected Vehicle (CV) Services. If this happens, the Telematics
Communication Unit (TCU) will switch to Deactivation Mode.
Any of the following conditions will initiate Deactivation Mode:
•
•
•
•
•

Customer does not enroll into CV services within 5 days from Retail Date (RDR/Warranty Start Date).
Customer unsubscribed from CV services.
CSP04 (Opt-Out)
Free trial period has expired.
Customer unsubscribed from CV services prior to February 26, 2023 (Mazda IT batch deactivation).

NOTE:
• Customer/Dealer can activate CV services anytime via MyMazda app (there just might be a slight delay in making
the backend connection since it was temporarily deactivated).
• When TCU is in Deactivation Mode, infotainment Over-the-Air (OTA) Connectivity Master Unit (CMU) software
update is not possible (disabled).
• Prior to Retail Date, the TCU is active.
Deactivation Mode Status Check:
Reception Icon Shows normal strength

TCU Active

Infotainment
Center
Display

Mazda
Connected
Vehicle
Viewer
(MCVV)

• TCU in
Deactivation
Mode
• One Time
Passcode
(OTP) is
processing

Reception Icon Shows "X"

1. Go to Mazda
Connected Vehicle
Viewer (MCVV)

Page 6 of 26

06/12/2023 11:31 AM tlawrenc

2. Select "Vehicle
Communication
Line Status
Reference"
3. Enter VIN and
then select
"Search"
TCU in Deactivation Mode (Status -> Closed)

One Time Passcode (OTP) is processing (Status -> Open Requested)

4. See Status

TCU Active (Status -> Opened)

REPAIR PROCEDURE
CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another
vehicle will disable Connected Services on both vehicles.
Page 7 of 26

06/12/2023 11:31 AM tlawrenc

PREPARATION:
1. Confirm that the TCU is at the latest software level. Go to Telematics Communication Unit (TCU) Updates
2. Go to eMDCS Vehicle Inquiry and confirm the following campains are not shown or closed:
•
•
•
•

CSP06
CSP07
SSPC7
DRW41

3. Go to eMDCS Vehicle Inquiry and confirm CSP04 is not shown.
4. Confirm the customer's phone and vehicle have good to strong reception during the concern as shown in the table
below.

• If the reception icon shows "X", the vehicle is possibly is in Deactivation Mode.

• Customer/Dealer can activate CV services anytime via MyMazda app (there just might be a slight
delay in making the backend connection since it was temporarily deactivated).
• If the reception is weak, move the vehicle to a location where the reception is good to strong as shown in
the table, then try to get the Authorization Code and/or operate the remote functions before proceeding to
the Repair Procedure if there is still an issue.
• If the reception is good to strong, proceed to Connected Vehicle Troubleshooting below.
NOTE: Vehicles stored for long periods may loose GPS clock sychronization. If the vehicle is stored for a long
period, test drive the vehicle to give the GPS clock time to sychronize before enrolling or testing connected vehicle
functions.
Index
1. Unable to create a MyMazda account
2. Remote function(s) inoperative
3. No One Time Pass Code (OTP)
4. Connected vehicle reception strength icon shows "X" or "\"
5. MyMazda App displays incorrect tire pressures (Except CX-5 and CX-9)
6. Unable to activate Connected Services (2019 Mazda3)
7. Software Update Error (2020 Mazda3)
Page 8 of 26

06/12/2023 11:31 AM tlawrenc

8. Functions inoperative (2021-> CX-30, CX-50, Mazda3 and MX-30)
9. First remote control attempt fails, second attempt works fine
10. Engine turns off when opening door
11. Low Tire pressure will not clear after correcting tire pressue
12. MyMazda App does not display tire air pressures (CX-5, CX-9)
Educational Videos
Resources
Connected Vehicle Troubleshooting
Symptom

Cause

Action

The customer is not able to create a
MyMazda account. The customer
receives the following error:
MyMazda App - Internal Usher SDK
error.

1. Text “Start” to 1-949 518-0058 (Twilio SMS for
Mazda)
2. Retry to create a MyMazda account.
Customer
NOTE: USA and Canada only
inadvertently
texted “Stop”
to 1-949 5180058
(Twilio SMS for
Mazda)

1

MyMazda Website - ERROR! Unable to
send one-time password.

Page 9 of 26

06/12/2023 11:31 AM tlawrenc

Push Notification

Remote function(s) inoperative.
2

• Engine Start / Stop
• Door Lock / Unlock
• Lights ON / OFF

OS Lock
Home
Screen
Tap the
Tap the push alert
notification
card

Go to the
MyMazda App
to view the
reason for
remote function
failure.

Inbox
Detail
Tap
"check
vehicle
status"

Go to the MyMazda App INBOX > ACTIVITY HISTORY -> to view
reason for remote function failure.

Activity History

Go to eMDCS Vehicle Inquiry and confirm the
following campains are not shown or closed:
Campain Status

• CSP06
• CSP07
• SSPC7

Page 10 of 26

06/12/2023 11:31 AM tlawrenc

• DRW41
1. Use MDARS to ID the vehicle and check for DTC's
stored. Are DTC(s) stored?
• Yes - Go to MGSS and perform normal DTC
diagnostics.
• No - Go to next step.
2. Confirm TCU software version is at the following
using TCU Software Version Check
•
•
•
•
•
•

Mazda3 - 10006 or later
CX-30 - 10006 or later
CX-5 - 10023 or later
CX-9 - 10023 or later
MX-30: 10019 or later
CX-50: 10003 or later

Troubleshooting 3. Disconnect battery for 30 seconds and then
needed
reconnect (KAM reset).
NOTE: Test drive vehicle after battery
disconnect to allow the GPS clock to
sychronize before retrying Authorization Code.
4. Perform one of the following:
• Customer: Un-enroll Connected Services,
then re-enroll into Connected Services as a
new primary user.
• Dealer: Perform customer take-over
enrollment for test confirmation, then at
customer pick-up, inform customer to re-enroll
into Connected Services as a new primary
user.
5. Contact Hotline for additional technical support if
needed.
Only a single
remote request Customer needs to wait 60 seconds for the initial
can be made
request cycle to be completed to make the second
per 60-second request.
period
Remote
Transmitter
Key(s) in the
vehicle

Do not leave keys in vehicle.

1. Aftermarket 1. Remove the aftermarket accessory.
Remote Engine 2. The customer can use either the Mazda Remote
Page 11 of 26

06/12/2023 11:31 AM tlawrenc

Start accessory
installed.
2. Mazda
Remote Engine
Start (BCKAV7-620)
accessory
installed.

Engine Start accessory or the MyMazda app function.
Cannot use both.
Mazda Remote Engine Start (RES) Removal