Technical Service Bulletin

01-16-13 - Engine, Misfire Diagnostic Aid

Transaction No:

2033805/8

Release date:

6/15/2023

Condition
Applicable Vehicles
Model(s)

Year

Eng. Code

Trans. Code

VIN Range
From

VIN Range To

All

2008-2024

All Gasoline
Engines

All

All

All

(Except Routan,
ID.4)

Revision Table
Instance Number

Published Date

Version Number

Reason For Update

2033805/8

6/15/2023

01-16-13

Include model year 2024
applicability.

2033805/1

5/9/13

V011314

Original publication.

The MIL is flashing or illuminated.
One or more of the following DTCs are stored in the ECM fault memory:

DTC
P0300
P0301-P0308
P130A

Description
Random/Multiple Cylinder Misfire Detected
Cyl.1 Misfire Detected – Cyl.8 Misfire Detected
Hide Cylinder

Engine may also exhibit reduced performance without significant loss of power.
Note:
Multiple components SHOULD NOT be replaced for 1 misfiring cylinder.

Page 1 of 5
© 2023 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

01-16-13 - Engine, Misfire Diagnostic Aid

Transaction No:

2033805/8

Release date:

6/15/2023

Technical Background
Misfire faults have commonly been related to conditions such as:
 Loose or damaged electrical connections
 Circuit grounds
 Poor fuel quality

Production Solution
Not applicable.

Service
 There can be multiple causes for engine misfire, ensure all campaigns and applicable technical
service bulletins (TSBs) have been performed.
 Repeat repairs must be carefully addressed to identify the root cause of the concern. Utilize proper
diagnosis steps to ensure that the concern has been identified, vehicle is repaired properly, and that
the repair is verified.
 To repair the vehicle correctly, obtain as much information as possible from the customer about the
symptoms of the condition and when it occurred.


In what situation (turning, acceleration, rolling stop, etc.) does the condition occur?

 Under what environmental conditions (road conditions, weather, temperature, start conditions, etc.)
does the condition occur?
 What is the operating situation of the vehicle (activated electrical equipment, gear selection, etc.)
when the condition occurs?
 Can the complaint be reproduced?
Workshop procedure
1. Read out the data memory of Engine/Motor Control Module -J623-, and note the environmental
conditions on the DTC log.
1a. If there are other entries in addition to combustion misfires, address the other entries before
addressing the cylinder misfires.
1b. If DTC P0301 – P0308 (Cyl.1 Misfire Detected - Cyl.8 Misfire Detected) is accompanied by P1250
(Fuel level too low), it is likely the faults occurred due to low fuel level, and not a component malfunction.
1c. Review all applicable TSBs related to cylinder misfires and ECM software improvements before
diagnosing the misfire condition.
2. Try to duplicate customer complaint based on the environmental conditions at the time the DTC was
set. The freeze-frame data gives important indicators for the traceability of the complaint, in particular, if it
occurs sporadically or at cold start.
Page 2 of 5
© 2023 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

01-16-13 - Engine, Misfire Diagnostic Aid

Transaction No:

2033805/8

Release date:

6/15/2023

Note:
If cylinder misfire faults are sporadic and a P130A Hide Cylinder fault is not present, it is likely that the
misfires may be caused by poor fuel quality, and are not related to a faulty component.
The fault memory should be cleared and the vehicle test driven to verify that the misfire faults do not
return.
3. Review the vehicle repair history for previous misfire or maintenance service that could be related to
the current complaint.
4. Observe the requirements of Guided Fault Finding. Perform Guided Fault Finding in full, according to
the proposed sequence (test plan). DO NOT skip any steps.
5. Complete Guided Fault Finding correctly and set the readiness code.
 A Proper GFF misfire diagnosis must be followed before replacing any components.
Tip
This is important to ensure that no subsequent faults occur due to the misfire.
6. In the case of single cylinder misfires:
6a. Before replacing components, determine whether the misfire migrates to other cylinders after
swapping components between cylinders (spark plugs, ignition coils and fuel injectors if practical). If
necessary, perform a test drive to ascertain this.
6b. If the misfire migrates and follows a specific component:
 Interrupt and resume GFF during component swap, re-read the DTC memory indicating that the fault
changed cylinders.
 Replace the defective part.
6c. If the misfire does not migrate:
 Interrupt and resume GFF during component swap, re-read the DTC memory indicating that the fault
did not change cylinders.
 If fuel injectors were not previously swapped between cylinders, a fuel injector internal leakage test
should be performed to verify if an internally leaking fuel injector is causing the misfire fault.
 If the fuel injectors pass the internal leakage test, or if the fuel injectors were swapped and the misfire
remains steady, a cylinder compression test should be performed and repairs diagnosed as
necessary.
7. In the case of multiple cylinder misfires:
7a. Before replacing multiple components, determine whether misfire faults are attributed to other
possible issues. For example, if data shows that the DTCs were sporadic, search Elsa for TSBs related
to cylinder misfires or ECM software improvements before diagnosing the misfire condition.

Page 3 of 5
© 2023 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

01-16-13 - Engine, Misfire Diagnostic Aid

Transaction No:

2033805/8

Release date:

6/15/2023

7b. Check to verify if one component may be influencing multiple cylinders. Use misfire monitor in GFF to
determine if misfires are continuous (which may indicate a faulty component), or sporadic (which may
indicate other possible issues).
7c. Determine whether the misfires migrate to the other cylinders after exchanging components. If
necessary, perform a test drive to ascertain this.
7d. If the misfire migrates and follows a specific component:
 Interrupt and resume GFF during component swap, re-read the DTC memory indicating that the fault
changed cylinders.
 Replace the defective part.
7e. If the misfire does not migrate:
 Interrupt and resume GFF during component swap, re-read the DTC memory indicating that the fault
did not change cylinders.
 If fuel injectors were not previously swapped between cylinders, a fuel injector internal leakage test
should be performed to verify if an internally leaking fuel injector is causing the misfire fault.
 If the fuel injectors pass the internal leakage test, or if the fuel injectors were swapped and the misfire
remains steady, a cylinder compression test should be performed and repairs diagnosed as
necessary.
8. Interrupt and resume GFF during any component swap, and then re-read DTC memory indicating that
the fault either changed cylinders or did not return.
8a. If misfires are determined to be related to a specific component(s) (fuel injector, spark plug, ignition
coil), replace only one defective component at a time and re-evaluate the concern.
Note:
If it is determined through Guided Fault Finding that a component has caused a misfire, the repair should
only include the component causing the misfire.
All fuel injector, spark plug, or ignition coil replacements must accompany a corresponding misfiring
cylinder to avoid unnecessary part replacement.
Misfire code P0300 – random/multiple cylinder misfire is not a probable cause to replace all fuel injectors,
spark plugs, or ignition coils. A cylinder specific P030X fault (P0301-P0308) should always accompany a
misfiring cylinder.
9. Verify repair under the same environmental conditions (e.g.: engine speed, engine load value, vehicle
speed, coolant temperature, intake air temperature, ambient air pressure, voltage at terminal 30, etc.) as
noted on the DTC log.

Page 4 of 5
© 2023 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

01-16-13 - Engine, Misfire Diagnostic Aid

Transaction No:

2033805/8

Release date:

6/15/2023

Warranty
Information only.
Note:
If a fuel injector, spark plug, or ignition coil is replaced for a misfire concern, the failed component must
have a misfire code (P0301-P0308) related to the misfiring cylinder.
Misfire code P0300 – random/multiple cylinder misfire must have the affected cylinder identified for
reimbursement.
Tip:
For warranty reimbursement, the Guided Fault Finding log identifying that the issue either changed
cylinders during the test, or shows a failed fuel injector internal leakage test, must be available upon
request.
Each part replaced must have a corresponding misfire fault on the documented Guided Fault Finding log
for reimbursement.

Required Parts and Tools
No special parts required.
No special tools required.

Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.

Page 5 of 5
© 2023 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.