Technical product information
Topic
Market area
Brand
Transaction No.
Level
Status
Release date

Flying B mascot clear wings replacement procedure
Bentley: worldwide (2WBE)
Bentley
2069611/2
EH
Approval

New customer code
Object of complaint
Complaint type
Position
body -> vehicle front end, vehicle rear end
high-volume parts
body fixtures and fittings -> trim, protective strips, brightware, dirt deflector -> brand badge component / consumables -> missing front

Vehicle data
New Flying Spur
Sales types
Type
ZG2*
ZG2*
ZG2*
ZG2*

MY
2020
2021
2022
2023

Brand Designation Engine code Gearbox code Final drive code
E
*
*
*
E
*
*
*
E
*
*
*
E
*
*
*

Documents
Document name
master.xml
3094-gel-rev-apds.pdf

INTERNAL

Technical product information
Flying B mascot clear wings replacement procedure

Transaction No.: 2069611/2

Customer statement / workshop findings
One or both of the Flying B mascot clear wings are missing (Figure 1)

Figure 1
In the event that one Flying B wing is missing the operative must replace both wings to eliminate a repeat repair
VERY IMPORTANT: It is no longer a requirement to replace the complete Flying B mascot assembly if the clear wings are
missing, the process within the Measure section details how to fit new replacement clear wings

Technical background
The adhesive that must be used to secure the Flying B clear wings is Dymax Ultra light weld 3094-GEL-REV- A
This must be sourced locally by copying/pasting one of the following links into your browser:
https://dymax.com/sales-support/contact-us/global-contacts
Or
https://dymax.com/forms/find-a-partner
The adhesive is available for sourcing in the following countries:
· Australia
· Austria
· China
· Costa Rica
· Czech Republic
· Denmark
· Dominican Republic
· Egypt
· Finland
· France
· Germany
· Hungary
· India
· Israel
· Italy
· Japan
· Malaysia
· Mexico
· Netherlands
· Norway
· Poland
· Puerto Rico

INTERNAL

·
·
·
·
·
·
·
·
·
·
·
·

Romania
Russia
Singapore
Slovenia
South Korea
Spain
Sweden
Switzerland
Thailand
Turkey
United Kingdom
USA

In the event the adhesive cannot be sourced locally by using one of the afore listed links
Or
The applicable country is not listed the operative should raise a Service Call and await feedback before conducting with any
further work
Please ensure the following information is included within the Service call
•

My country is not listed within the country matrix

Or
•

The adhesive cannot be sourced locally through the suggested regional Dymax supplier

CAUTION
DO NOT UNDER ANY CIRCUMSTANCES USE A DIFFERENT TYPE OF ADHESIVE OTHER THAN THE TYPE SPECIFIED

NOTICE
The following must also be sourced locally before continuing with the onward process
UV light (Figure 2) the specification must be as follows:
•

Minimum power output must be 5W

Figure 2
The UV Wavelength must be as follows:
•

Minimum wavelength of 395nm (nanometres)

•

Grey or dark brown UV safety glasses must be worn when conducting the adhesive bonding procedure

•

Standard safety glasses must be worn whilst conducting all other steps other than the UV adhesive bonding procedure

INTERNAL

•

Dymax Ultra light weld 3094-GEL-REV- A - 30 ML (Figure 3)

•

3M surface cleaner or same specification

CAUTION
VERY IMPORTANT: The adhesive must not be applied if the Use by date has expired
– Ensure the adhesive is stored as per all manufacturers instructions

IMPORTANT: Once the adhesive has been opened both caps (ARROWS) must be refitted as the adhesive will solidify
Tip: if the caps are refitted as instructed the adhesive should be suitable to use up to the Use by date
IMPORTANT: In the event the adhesive has been left open without one or both caps fitted the adhesive must be discarded as
per all local environmental guidelines, a new tube of adhesive must then be sourced

Figure 3
•

Adhesive application gun (Figure 4)

Figure 4

Production change
-

Measure
CAUTION
DO NOT UNDER ANY CIRCUMSTANCES ATTEMPT TO REPLACE THE FLYING B MASCOT WINGS WITHOUT REMOVING THE FLYING B
ASSEMBLY FROM THE VEHICLE AS PER REP.GR 66
DAMAGE CAN EASILY BE CAUSED TO THE RADIATOR SHELL AND/OR BONNET, WARRANTY PAYMENTS WILL NOT BE
CONSIDERED FOR ANY DAMAGE TO THE RADIATOR SHELL/BONNET AND ASSEMBLY (INCLUDING MASCOT)
1) Referring to Rep.Gr 66 - Remove the Flying B assembly from the vehicle
In the event that one of the Flying B clear wings is missing, the operative should remove the existing wing as detailed in step
1
Or
If both Flying B clear wings are missing, continue from step 2

NOTICE
NOTE: Warranty payments will not be considered for any damage to the Flying B mascot
Hint:: In the event that one of the clear wings is missing and the opposing wing requires removal in most cases the clear wing can be easily
removed by using a suitable non metallic tool to remove/push out the wing from the mascot
INTERNAL

However
In the event the remaining clear wing is difficult to remove please refer to the steps below
1) Due to the location of the LED light (Figure 5) damage can be caused to the Flying B mascot therefore it is imperative the wings are drilled at
the exact location shown within Figure 6

Figure 5

Figure 6
•

Safety glasses and gloves must be worn for the duration of this repair process (Figure 7) UV safety glasses are also required to be used
when advised within the TPI

Figure 7
CAUTION
The use of suitable protective gloves is imperative as the clear wings must be kept clean on the inside and outside as well as the edges, do not
conduct the onward procedure without wearing suitable gloves

Once removed from the vehicle the operative must ensure the Flying B assembly is placed on a clean protective surface The use of a suitable countersink drill (3mmx1.6mm) is recommended (Figure 8) the countersink drill must be capable of a
making a hole with a maximum width of 3mm, the tool Must Not contact the mascot or LED

INTERNAL

Figure 8
Hint: A standard 3mm drill bit can be used however the drill must be used in conjunction with a drill stop tool to ensure a
depth of 3mm is not exceeded (Figure 9)

Figure 9
•

Do not use a standard drill without using a drill stop as damage can easily be caused to the mascot or LED (Figure 10)

Figure 10
•

Once the hole is drilled use a suitable pick tool to remove the wing

HINT: In the event the glass is secure please use a suitable heat gun (select a low setting to soften the previously applied adhesive)
WARNING
Warning: Take care not to apply excessive heat as damaged can be caused to the Flying B and the LED inside the Flying B, any damage will
not be covered under Warranty
2) Referring to Figure 11 - Using foam cleaning tips in conjunction with 3M surface cleaner thoroughly clean the Flying B aperture

INTERNAL

Figure 11
CAUTION
Once the adhesive has been removed using the 3M cleaner the operative should wait 60 seconds to allow the liquid to evaporate

3) Check to confirm that no traces of the original adhesive are evident

NOTICE
IMPORTANT: In the event there are traces of adhesive this must be removed using a suitable non-metallic tool noting
CAUTION
Before applying the adhesive the operative must ensure the following:
– Ensure the Use by date has not expired
– Ensure a new nozzle is always used
– Before applying the adhesive ensure that any air within the nozzle is removed prior to applying the adhesive
4) Referring to Figure 12 - Apply the adhesive as shown ensuring the adhesive is applied in a consistent manner noting the following:
Should the adhesive dosage be sporadic/not consistent (Figure 13) there is a risk of insufficient sealing and water ingress
•

Poor Cleaning of the Flying B mascot can lead to debris inside the mascot

•

Should too much adhesive be applied the excess will be visible and would be seen through the clear wings

INTERNAL

Figure 12

INTERNAL

Figure 13
CAUTION
CAUTION before fitting the clear wings the operative MUST ensure the wings are fitted in the correct location ensuring the serrations are on
the outer sides as shown in Figures 14 and 15
•

Figure 14 - Left hand side

Figure 14

INTERNAL

•

Figure 15 - Right hand side

Figure 15
5) Referring to Figure 16 - Ensuring suitable gloves are worn – Use suitable double sided tape to hold the wing at the location shown, fit the
replacement wing ensuring the adhesive is not disturbed, once fitted wipe away any excess adhesive from the outside of the clear wing and
mascot using a clean cloth and 3M surface cleaner
CAUTION
Do Not hold the wing as shown in Figure 17 as the adhesive can easily be disturbed when using this method

Figure 16

INTERNAL

Figure 17
6) Once fitted the wing should be as shown in Figure 18
CAUTION
CAUTION before fitting the clear wings the operative MUST ensure the wings are fitted in the correct location ensuring the serrations are on
the outer sides as shown back in Figures 14 and 15

Figure 18
7) Referring to Figure 19 - With the Flying B assembly placed on a suitable clean surface – Ensure suitable UV safety glasses are worn - Switch
on the UV lamp

NOTICE
The operative should be aware that the distance quoted of 100mm and the time of 60 seconds to cure the adhesive may vary depending on
the type of light which has been sourced, the operative should refer to the manufacturer’s instructions of the lamp
NOTICE
Ensure the beam is projecting equally onto the newly fitted clear wing for a duration 60 seconds as shown in Figure 19

INTERNAL

Figure 19
8) Repeat steps 2 through to 7 on the opposing side of the mascot
9) Once both wings have been fitted - Refit the Flying B assembly - Refer to Rep.Gr 66

Warranty accounting instructions
Time to remove the Flying B assembly and replace both Flying B mascot wings
Warranty Type
110 or 910
Damage Service Number 66 07
Damage Code
00 10
Time to replace both Flying B mascot wings
Labour Operation Code 66 07 50 51
Time
20 TU
Time to remove and refit the radiator grill
Labour Operation Code
66 05 19 00
Time
30 TU
Time to remove and refit the Flying B assembly
Labour Operation Code 66 07 1 950
Time
10 TU

NOTICE
IMPORTANT: As the kits can be used on 5 vehicles the operative must claim a quantity of 0.2x Kits per repair, this is to ensure a full kit of parts
is not claimed for every repair
INTERNAL

Parts information
NOTICE
Dymax Ultra light weld 3094-GEL-REV- A must be sourced by using one of the following links:
https://dymax.com/sales-support/contact-us/global-contacts
Or
https://dymax.com/forms/find-a-partner
3SE 898 810 - REPAIR KIT FLYING B WINGS (Figure 20)
The kit contains the following and can be used on multiple vehicles
•

Syringe Needles x5

•

Sets of clear wings x10 (5 left hand side wings - 5 right hand side wings)

•

Foam Cleaning Tips x5

Figure 20

NOTICE
IMPORTANT: As the kits can be used on 5 vehicles the operative must claim a quantity of 0.2x Kits per repair, this is to ensure a full kit of parts
is not claimed for every repair

INTERNAL