Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SC264 Multiple Models May 2023

Page 9 of 13
SUBJECT:

5.

APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL (SC264)
Once the camera and display are properly
oriented, bend the probe just behind the
camera to help maintain orientation during
inspection.

 NOTICE
If it is difficult to view the inside of the
arm with the camera due to flexibility
of the scope wand, use the 90-degree
lens attachment.
6.

Insert the camera into hole as shown.

 NOTICE
Always ensure the camera lens and
90-degree adaptor are cleaned with a
fresh paper towel and rubbing alcohol
prior

to

inspection

and

image

capturing.

7.

Rotate the camera in order to check all angles
for proper wax application inside the inspected
components, and to obtain your images that
will be used for warranty claim submission.

Note: See examples below of “before” and “after” wax application.
Before Wax Application

After Wax Application

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SC264 Multiple Models May 2023

Page 10 of 13
SUBJECT:

APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL (SC264)

Undercoating Spray Application:
WARNING
Do not eat, drink, or smoke while using this product. Keep away from heat, sparks, open flames, hot
surfaces, and other ignition sources. Avoid breathing mist, vapors, spray. Wash thoroughly after
handling. Wear protective gloves, protective clothing, eye protection, face protection.
Use with adequate ventilation. Respiratory: Level of exposure needs to be determined. If required,
use a particulate filter, a NIOSH-approved air purifying respirator with organic vapor cartridge or a
supplied air respirator. Filters should be replaced when breathing becomes labored. Cartridges
should be replaced when odors pass through. Refer to MSD sheets (Links: Cavity Wax,
Undercoating) for additional information and important warnings. All warnings provided by the
MSD sheet are hereby incorporated by reference.
1.

Using undercoating spray, be sure to completely coat the Sub Frame, Front Lower Arms, Fuel/Brake
Tube Line, and Torsion Axle Complete.

Sub-Frame

Front Lower Arms (LH/RH)

Torsion Axle Complete

Fuel & Brake Tube Lines

 NOTICE
Be

sure

to

thoroughly

spray

undercoating on all sides of fuel and
brake tube lines (above and below).

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SC264 Multiple Models May 2023

Page 11 of 13
SUBJECT:

2.

APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL (SC264)
Spray undercoating on the Two-way Brake Tube Connector, Flexible Brake Hose, Fuel Tank Bands, and
Parking Brake Cable Brackets.

CAUTION
Be careful NOT to spray undercoating onto the brake calipers or friction surfaces during
application as it may reduce brake performance when operating.

3.

Two-way Brake Tube Connector

Flexible Brake Hose

Parking Brake Cable Brackets

Fuel Tank Bands

Be sure to completely coat the four (4) brake hose anchor clips on both sides, front and rear of the
vehicle.

4.

If previously removed, reinstall the splash shield.

5.

Assemble the fuel and brake tube clips and side under cover in the reverse order of removal.

 NOTICE
Allow cavity wax and underbody coating to cure for a least 1 hour prior to vehicle being
driven, especially during rain or snow conditions.
Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SC264 Multiple Models May 2023

Page 12 of 13
SUBJECT:

APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL (SC264)

AFFECTED VEHICLE RANGE:
Model

Production Date Range

Forte (YD)

July 25, 2017 to April 30, 2018

Forte (YDm)

May 9, 2016 to July 23, 2018

Rio (UB)

June 21, 2011 to March 31, 2017

REQUIRED TOOL:
Tool Name
Wax Injection Gun
& Nozzle

Part Number

Figure

Comments

06700 10100

Wax Application Hose

06700 10110

Borescope Kit

1K545 4D200QQK

Initial supply was
auto shipped to Dealers
for SC141.

Air Pressure
Regulator

IRCR37121600

For replacements,
contact Snap-On
Business Solutions

Respirator
(Organic/
N95 Particulate)

SSC366150

Cartridge for
Respirator (6pk)

SSC100100

Filter for
Respirator (12pk)

SSC106000

Hammer

-

Air Gun

-

Brush

-

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SC264 Multiple Models May 2023

at (888) 542-1011

Locally Sourced

Page 13 of 13

APPLICATION OF ADDITIONAL ANTI-CORROSION MATERIAL (SC264)

SUBJECT:

REQUIRED PART:
Part Name

Part Number

Kia Frame Rust

Figure

Qty.

Comments

1

Limit one (1) can
per vehicle
(Order through
Kia Chemicals)

3

Limit three (3) cans
per vehicle
(Order through
Kia Chemicals)

UM090 CH041

Preventative

Undercoating Spray

UM010 CH044

WARRANTY INFORMATION:
N Code: N99 C Code: C99
Model

Claim

Causal

Type

P/N

Qty.

Repair

Labor Op

Op

Replacement

Description

Code

Time

P/N

65110

UB

1W301
(SC264)

YD

V

65100
A7200

0

Qty.

UM090 CH041

1

UM010 CH044

3

UM090 CH041

1

UM010 CH044

3

220107R0

Application of

0.8

Anti-Corrosion

M/H

Material
YDm

65100

220M13R0

A7000

 NOTICE
VIN inquiry data for this repair is provided for tracking purposes only. Kia retailers should reference
SC264 when accessing the KDealer+ system.

Printed TSB copy is for reference only; information may be updated at any time. Always refer to KGIS for the latest information.

TSB: SC264 Multiple Models May 2023