INDIAN MOTORCYCLE

HELP CENTER
What can we help you find?

SEARCH

Help Center Home / Article

4/10/2023

2014+ Chieftain Drive Belt Inspection and Tension Adjustment
Indian Chieftain Drive Belt Inspection and Tension Adjustment - Indian Motorc…
Motorc…

Required Tools and Supplies:
27mm crowfoot wrench
Belt tension tool or 10-pound weight
Marker
6mm Allen and 13mm socket
Ratchet
Breaker bar
Torque wrench

To learn more about tools, read the Tools and Fasteners Guide.
Always wear safety glasses and nitrile gloves when servicing your Indian Motorcycle. To inspect and
adjust the drive belt tension on your Indian Chieftain, follow these steps:

1. Park the bike on a flat, level surface and allow it to cool completely.
2. Remove the upper side covers by pulling the corners straight out to disengage from the rubber
grommets in the frame.
3. To remove each saddlebag:
First, disconnect the saddlebag lock connector near the seat.
Next, press the lid latch release button and lift the lid.
Remove the two saddlebag fasteners with a 6mm Allen socket.
Finally, tilt the saddlebag out and lift up to remove.

4. Next, lift the motorcycle according to your Owner’s Manual guidelines and elevate the rear wheel.
The motorcycle must be stable before proceeding.
5. Ensure the motorcycle is in NEUTRAL.
6. Inspect the drive belt for damage and wear. Refer to your Owner’s Manual for belt wear analysis.
If inspection reveals a need for replacement, see your authorized Indian Motorcycle Dealer.
7. Next, check and record the belt deflection next to the deflection window, applying 10 pounds of
force. Ensure the belt is dry before measuring. To check tension, push up on the belt with a tension
tool, or use a 10-pound weight to apply pressure downward on the belt.
Using the tire valve stem as a reference, measure at three additional points 90 degrees apart on the tire. The drive belt
deflection at 10 pounds of force should be 34mm (1.3 inches) or 11 notches up the belt guard.
If adjustment is needed, rotate the wheel forward and mark the tightest measurement point on the tire for reference.

8. Also mark the current adjuster locations on both sides of the rear wheel for reference.
9. Next, place a rag against the exhaust to prevent scratching the paint. Loosen but do not remove
the axle nut with a 27mm wrench.
10. Then retighten the nut to 15 ft-lbs (20 Nm) with a 27mm crowfoot wrench.
11. Turn the right-side adjuster nut with a 13mm socket to achieve proper belt tension.
12. When the belt tension is correct, inspect the belt for proper alignment.
13. To minimize change in belt tension, use the left-side adjuster only to make final adjustments to
belt alignment. Ensure the axle is seated forward against the axle adjusters during this procedure.
14. While rotating the wheel backward, tighten the left-side adjuster nut until the drive belt is
centered in the driven pulley. Sprocket teeth should be visible on both sides of the drive belt.
15. Once the desired setting is achieved, rotate the wheel forward and verify the sprocket teeth are
still visible on both sides of the drive belt.

16. If necessary, revert back to the initial settings and repeat this process as needed.
17. Re-check drive belt tension to verify it is still within specification. Improper tension or alignment
can cause drive line noise and damage the drive belt.
18. Tighten the rear axle nut to 65 ft-lbs (88 Nm).
19. Pump the rear brake pedal several times to reset brake pad distance.
20. Verify the wheel rotates smoothly and freely without drag when the brake pedal is released.
21. Safely lower your motorcycle to the ground. Refer to your Owner’s Manual for helpful hints and
techniques.
22. To reinstall the saddlebags:
Place each bag in a fully seated position on the muffler.
Reinstall the saddlebag fasteners. Torque to 18 ft-lbs (24 Nm).

23. Then reconnect the electrical wiring if necessary, and ensure the saddlebags are mounted
properly.
24. Finally, align the three side panel grommets and reinstall each upper side panel.
For more information, see your authorized Indian Motorcycle Dealer. Find a dealer near you with
the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
YouTube® is a registered trademark of Google LLC
Unless noted, trademarks are the property of Indian Motorcycle International, LLC
© 2022 Indian Motorcycle International, LLC
Was this article helpful?
Yes, it answers my question
No, it's missing information or visuals
No, the instructions are unclear
No, What are the next steps?
No, I'm experiencing a technical error
Other

* [-] How can we improve this article? We'd love to hear your suggestions
Tell us what you would like to see in this article

SEND
Keyword(s) video , maintenance , belt , inspect , inspecting , adjust , adjusting ,

HELPFUL LINKS
Parts, Accessories and Apparel
Owner's Manuals
Indian Motorcycle Protection Plan
Special Offers
Recalls
Indian Motorcycle Lubricants

CONTACT US
BY E-MAIL
Send us an e-mail inquiry.

CLICK TO CALL

BY DEALER
Locate the nearest dealer in your area.

Find A Dealer Near You
Enter City, State or Zip Code

55033

SEARCH

Use Current Location

Filter By (Optional)
Show dealers that offer online service scheduling

SUBSCRIBE NOW
FIND A DEALER
US-ENGLISH

MOTORCYCLES
SHOPPING TOOLS
ASSISTANCE
OWNER RESOURCES
ABOUT US
© 2023 Indian Motorcycle
Site Map
Privacy
Cookie Preferences

Terms
Accessibility
Careers
Global Sites

Reset Filters