SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from a failure to update the diagnostic and reprogramming software
are not covered under warranty.
i-HDS Software Version 1.008.008 or later
Honda ECU Reprogramming 3.0.6.0 or later
Update only the systems and software listed in this service bulletin.
Do not use the MongoosePRO VCI for this service bulletin as it is not an American Honda-approved device.
For more information about updating vehicle systems, refer to service bulletin 01-026, Updating Control Units/Modules.
Year/Model Current Program ID New Program ID
2023 CR-V 8S102-3A0-A060 8S102-3A0-A08
8S102-3A0-A070
INSPECTION PROCEDURE
Connect the i-HDS and check for DTC’s.
+ — Ifthe DTC B2A60-99, Out of Automatic Correction Range for Misalignment of Multipurpose Camera Unit Image, is
visible then clear the DTC and proceed to the Repair Procedure to update the ACC/CMBS software.
+ If the DTC does not clear, continue with normal troubleshooting.
REPAIR PROCEDURE
+ Make sure the 12-volt battery is fully charged before starting an update.
* Connect a fully charged jumper battery to the vehicle, and leave it connected during the entire procedure to maintain
steady voltage.
+ Do not use the GR8 because the vehicle requires a steady electrical current
+ Control module failure caused by the improper completion of a software update (early key cycle, low battery voltage,
disconnected DLC cable, etc.) is not covered by warranty.
+ fan error occurs during the update or the i-HDS freezes, do not disconnect the battery or turn the ignition to
OFF. Reboot the i-HDS, and start over.
* To prevent control unit damage, do not operate anything electrical (headlights, audio system, brakes, A/C, power
windows, door locks, etc.) during the update.
+ Warranty reimbursement for technician labor is not allowed for routine checking/installation of any available software
update.
1. From the desktop, select i-HDS.
=
sHDS
¢
ae
Page 2 of 5

2. From the HOME menu, select the Honda ECU Reprogramming.
a
@
2 *
Connect tothe Vehicle ‘Stored Date Playback Settings
- -
Reloted appicabons Immobilizer Setup Toot Honda ECU Reprogramming
aw.
3. Enter the repair order number and press Read vehicle information.
NOTE: Wait until vehicle communication has completed.
a a
H odometer
Repo Order Number
12456
Fede ecter ep err cumber to continue
=. Print || Settings
Read vehicle infomation
\Vehide Kentifcaton Number (VIN) om
7aRWw2H73P¢000030 ssn
Repair Order Number
Succeeded Whats New infomation cowelocseg i
Fad to update
Selec the software to update (ome may not be selectable “
nog | or Seventeen a
ss BEC oe .
Estimated Time Slated @ min / AST
Page 3 of 5

4. Check the box to select the option for the camera update.
rosea tau Ropumning w60 =o x
em Print Settings
Read vei information )
\ebcle Wentication Number (VIN) im
‘Teaaw2H7302000020 seri
Repair Order Number
feady to updete =
Select the oftware o updete (ome may nt be selectable)
Started downlonding 05102 30.4000
Succeeded downloading 85102-3A0-A080 a
[sm | cae, Merman aaa
mo 88102-20-4060 $5102-200-108. 20M CV Peto ane id Front Camara Ute
pais EGLO Ib w are la
eres ‘ails a0-000 8 w ae om
ies SGA Ub se om
Eatimated Time: Selected 57 min / Al S7 min
stort
5. Press OK to begin updating.
®
se ses
ead vehi infomation syn
‘Vehicle Identification Number (VIN) meee
TENE EOP The following sofware will be updated.
ep Order Number Yosietes
1234 —
—_ =e
Ready to update . *
Select the softwere to updte ore may aot be
Sorted downloading #5102-940-AOED
Succeeded dowrlcading 25102 300-080 e
oe ca) oe) a
see Progam © progress cents
face a ies
lrov-ri 37-04-4690 > to date } o os
E ass = =| 2S
bass ioe cen 4 I on
sees CSTV te oe
fas es tg
Tatted Tone Selected 57min / AST min
im
= Ba HONDA ECU Repeogramening
Updetat in progress
Vere eran st Re
TrARW2HT2PE000090
apa Order Number
Ready to update *
Select the softre 0 pda
Stated downloading 85102
Soceeded downloting 8 e
cod a
i roped ‘cages | cont
eet oor conc fe
lace aie [owe
Page 4 of 5

6. When prompted, turn the ignition switch OFF, then turn the ignition switch ON.
pts mpegs sina
ee [rere
nina Bo eraircmaccenine
7. Once the camera is updated, the following screen appears, then select EXIT and close the ECU Reprogramming.
»
7 4) eatin rope
| ses oes
Venice entiation Ni |4/ wpe pregres
asivn7areocoa%0 ||| Tumi gnion etch oft
ee este
are Updatets} complete.
tsi vpte a
Sl he Sater upd
Sane Sowrlonng 2502
Screed dowisnng #5 :
ee SS Das |
Jecre 3
fro Soe C=] a
te Saeed = a +}
8. DoanALL DTC check in i-HDS, and then clear any codes set during the update.
END
Page 5 of 5