Figure 29

28.

Reinstall the hole cover.


Tuck the edges of the rubber
boot under the carpet on the top
and both sides (Figure 30)



Install the (4) bolts and start by
hand



Torque the bolts to
5.5 N●m(0.56 kg-m, 49 in-lbs)

Hole cover
(Rubber) boot

Tuck rubber
under carpet

Figure 30
11/22

PC950

29.

Harness
retainer

Install the harness retainers to the
hole cover. (Figure 31)

Figure 31
30.

Carefully install the center console
assembly.


Route the console rear first
through the RH door and toward
the rear of the vehicle
(Figure 32)



Align the front of the center
console with the instrument
panel



Align the parking brake handle
with the slot in the center
console
Figure 32

NOTICE: Be careful to not scratch the
interior components during reinstallation.

12/22

PC950

31.

Position the center console side
alignment tabs with the instrument
panel side trim on the LH and RH
sides of the center console.
(Figure 33)


Slide the center console forward



Align the console alignment tabs
with the console alignment holes
(just below mounting screw
holes) (Figure 34)



Install the (2) front console
screws (Figure 34)



Lower the front of the console
down

Console side
alignment tab

Figure 33

NOTICE: Be careful to not scratch the
interior components during reinstallation.

Console
alignment tab

Figure 34

Wiring
Harness

32.

Move the wiring harness connectors
upward through the openings in the
center console as shown in Figure
35 and Figure 36.


Lower the console all the way
down

Figure 35
Connector

Connector

Connector

Figure 36
13/22

PC950

33.

Install the USB port finisher.


Connect the (2) harness
connectors to the USB ports



Place the USB finisher in the
position shown in Figure 37, but
do NOT seat the retaining clips
at this time
USB finisher

NOTE:



An audible click will be heard once the
connector is fully seated.



Pull harness connector away from finisher
to verify they are seated properly

Figure 37

Console tray
finisher

34.

Install the Console tray finisher.


Carefully install the tray finisher
under the USB finisher
(Figure 38)



Starting with the rear of the
console tray finisher, seat the
retainer clips by pushing
downward (Figure 39)



Align the the USB finisher
assembly retaining clips and
push toward the front of the
vehicle to seat the retainer clips

Figure 38

NOTICE:
Be careful to not scratch the interior
components during reinstallation.

Figure 39

14/22

PC950

35.

Install the USB finsher screw.
(Figure 40)
USB finisher

Figure 40

36.

Install both LH and RH console side
finishers. (Figure 41)

Console side
finisher

Figure 41

37.

Install the (2) screws that secure
the console side finishers.
(Figure 42)

Figure 42

15/22

PC950

Shifter
finisher

38.

Place the shifter finisher over the
shifter assembly as shown in Figure
43.

Figure 43

39.

Trim ring correct
position

Place the shifter trim ring over the
shifter assembly. (Figure 44)


Locate the front of the trim ring
by placing it into the shifter
finisher and checking fitment



If the trim ring does not fit,
rotate the trim ring 180° and
verify trim ring fitment

Figure 44

Front center
of shift boot
stitching

40.

Lift the trim ring up and align the
front center of the shift boot
stitching with the front center of the
trim ring. (Figure 45)

Front center
of trim ring

Figure 45
16/22

PC950

41.

Carefully install the shift boot over
the trim ring. (Figure 46)


Align the shift boot holes with the
trim ring pins as shown in Figure
46
Shift boot hole
installed on trim
ring pin

Figure 46
42.

43.

Carefully install the trim ring and
shift boot into the shifter finisher.


Position the trim ring/shifter boot
over the shifter finisher
(Figure 47)



Carefully push the trim
ring/shifter boot into the shifter
finisher



Verify the shifter boot is aligned
with the stitching centered on the
front and the rear of the shifter
finisher (Figure 47)

Shifter boot
stitching

(Rear) Center of
shifter finisher

Figure 47

Install the (4) screws securing the
the trim ring to the shifter finisher.


Lift the shifter finisher upward
and install the (4) screws shown
in Figure 48

Figure 48

17/22

PC950

44.

Reconnect the ignition button and
the drive mode button (if equipped).
(Figure 49)

Ignition button

Figure 49

45.

Install the shifter finisher.
(Figure 50)


Align the shifter finisher
retaining clips with the center
console holes



Push the shifter finisher
downward to seat the finisher



Reinstall the console tray
finsher mat
Figure 50

46.

Raise the vehicle up on a lift enough to get the rear wheels several inches off the
ground.

47.

Enter the vehicle and verify the transmission is in the Neutral position.

18/22

PC950

IMPORTANT: This process should be performed with the rear wheels off the ground.
48.

Adjust the parking brake lever.
a) Lower the parking brake lever half way down
b) Tighten the parking brake lever adjustment nut
several turns Figure 51

Parking brake
adjustment nut

c) Completely lower the parking brake lever
d) Verify the rear wheels turn freely


If the rear wheels are difficult to turn or do
not turn, loosen the parking brake lever
adjustment nut 1-2 turns while rechecking
the rear wheel movement with each
adjustment

Figure 51

e) Slowly pull upward on the parking brake lever while counting the number of
notches (clicks)
f) The total number of clicks with moderate effort should be 6-7 clicks


Tighten the parking brake adjustment nut to reduce the number of clicks



Loosen the parking brake adjustment nut to raise the number of clicks

g) Completely lower the parking brake lever and check to make sure the rear
wheels spin freely

49.

Console release
button

Open the center console lid.
(Figure 52)


Console lid

Press the console release button
and lift the console lid to the
open position

Figure 52

19/22

PC950

Console
compartment

50.

Reconnect the center console
harness connector. (Figure 53)

Console lid
release button

Connector

Figure 53
Trunk release
switch
Harness
retainer

51.

Install the cup holder assembly.
Heated seat
Heated seat
switches
switches
(If Equipped)



Connect the harness
connector(s) for the trunk
release and heated seat (if
equipped) switches (Figure 54)



Insert the harness retainer into
the mounting point located on
the cup holder



Position the cupholder assembly
into the center console



Push the cupholder downward to
seat the retainers into the center
console (Figure 55)

Figure 54

Figure 55

20/22

PC950

52.

Move both seatbacks and seat
bottoms fully forward. (Figure 56)

Figure 56

53.

Install the (2) rear center console
screws. (Figure 57)


Move both seatbacks to the
original position

Figure 57

54. Perform the below quality checks for the shift control.
a) Verify there is no binding or abnormal noise when shifting transmission into each of the
gear positions.
b) Verify the shift boot is not damaged, twisted, or dislocated.
c) Verify the shift knob is straight.

21/22

PC950

CLAIMS INFORMATION
Submit claim using the following claims coding:
Work Order Line Type: “CM” Campaign
CAMPAIGN
(“CM”) ID
PC950

DESCRIPTION

OP CODE

FRT

Check Shift selector adjustment-OK

PC9500

0.2 hr

Check and adjust shift selector

PC9501

0.9 hr

22/22

PC950