T-SB-0109-22

December 14, 2022

2023 Mirai Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2023

Mirai

ADDITIONAL INFORMATION

Introduction

Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer
feedback indicates the following areas deserve special attention when performing PDS:





Careful inspection for paint chips/scratches and body dents/dings.
Proper operation of electrical accessories (including interior light, clock, and radio reset).
Interior cleanliness.
Proper function of mechanical systems.

Customer retention and proper maintenance of vehicles are and have always been a major focus
for Toyota. To help remind customers that regular service is essential to the proper maintenance
of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing
this, customers will be reminded to return to your dealership for service. Your current service
reminder sticker may be used. (See PDS Check Sheet item 8 of “Final Inspection and Cleaning.”)
This bulletin contains the PDS procedures that apply specifically to 2023 model year Mirai
vehicles. A universal PDS Check Sheet that contains PDS steps that apply to all 2023 model year
Toyota vehicles has been developed. To properly perform a complete PDS, you must complete
all procedures contained in this TSB as well as the universal PDS Check Sheet.
In addition, if the vehicle is stored for over 30 days, be sure to follow Long-Term Vehicle
Storage Guidelines.

© 2022 Toyota Motor Sales, USA

Page 1 of 11

T-SB-0109-22

December 14, 2022

Page 2 of 11

2023 Mirai Pre-Delivery Service (PDS)
Warranty Policy

If the need for additional repairs or adjustment is noted during PDS, the required service should
be performed under warranty. Reimbursement will be managed under the warranty policy.
The Warranty Policy and Procedures Manual requires that you maintain the completed
Check Sheet in the customer’s file. If you cannot produce a completed form for each retailed
vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will be subject
to debit.
An additional Repair Order completed in conjunction with normal PDS MUST have time
punch/flags for service. If multiple repairs are performed, separate time flags MUST be punched
for each repair.

Warranty Information
OP CODE

DESCRIPTION

MODEL

TIME

OFP

T1

T2

001013

Pre-Delivery Service (PDS)

Mirai

1.2

–

–

–

Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

Techstream ADVi*

QTY

TSADVUNIT

Techstream 2.0
Techstream Lite

PART NUMBER

TS2UNIT
ADE

Techstream Lite (Green Cable)

TSLITEPDLR01
TSLP2DLR01

*Essential SST.

NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 17.20.013 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.

© 2022 Toyota Motor Sales, USA

1

T-SB-0109-22

December 14, 2022

Page 3 of 11

2023 Mirai Pre-Delivery Service (PDS)
Procedures



D/C Cut Fuse Installation ........................................................................................................ 4



Tire Pressure Warning System (TPWS) Initialization .............................................................. 5



Memorize Steering Angle Neutral Point .................................................................................. 5



Dealer Contact Information for Call Dealer Head Unit Function .............................................. 5



Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation ................... 6



Front Wheel Opening Extension Pad Installation .................................................................... 8



Front License Plate and Mounting Bracket Installation* .......................................................... 9



Installation of Rubber Body Plugs* ........................................................................................ 11

*If applicable.

© 2022 Toyota Motor Sales, USA

T-SB-0109-22

December 14, 2022

Page 4 of 11

2023 Mirai Pre-Delivery Service (PDS)
D/C Cut Fuse Installation

To minimize battery discharge, the D/C cut fuse (30A) has been removed and is stored in the
engine compartment relay block. Install the D/C cut fuse (30A) and confirm ALL related
Diagnostic Trouble Codes (DTCs) are cleared.
Figure 1.

1

2

3

1

Relay Block

2

Remove D/C Cut Fuse (30A)

3

Install D/C Cut Fuse (30A)

© 2022 Toyota Motor Sales, USA

T-SB-0109-22

December 14, 2022

Page 5 of 11

2023 Mirai Pre-Delivery Service (PDS)
Tire Pressure Warning System (TPWS) Initialization

Refer to the applicable Repair Manual for the TPWS initialization procedure.
Note the spare tire does NOT have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using Techstream and select the compensation tire pressure
checkbox. Compensation pressures will display on the Health Check results screen. Adjust the tire
pressure when the tires are cold.

Memorize Steering Angle Neutral Point

As a result of the removal of the D/C cut fuse, the power source to the steering angle sensor is
cut off. When the D/C cut fuse is reinstalled, the parking assist monitor system will be operative,
but it cannot display guidelines to assist parking operation because the center position
recognized by the steering angle sensor may not be in an initial position. Therefore, perform
steering angle neutral point initialization AFTER installing the D/C cut fuse during PDS.
Refer to the applicable Repair Manual for the steering angle neutral point initialization procedure.

Dealer Contact Information for Call Dealer Head Unit Function

Refer to the Multimedia System Owner’s Manual to add dealer contact information.

© 2022 Toyota Motor Sales, USA

T-SB-0109-22

December 14, 2022

Page 6 of 11

2023 Mirai Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation

1. Remove the front AND rear emergency
towing eyelets from the front and rear
bumpers by turning them counterclockwise.

Figure 2.

HINT
If it is difficult to loosen the emergency towing
eyelets, use a steel bar.

1

2

2. Place the removed front emergency towing
eyelet into the luggage tray in the
luggage compartment.

1

Front Emergency Towing Eyelet

2

Rear Emergency Towing Eyelets

Figure 3.

HINT
Dispose of the other removed emergency
towing eyelets.

1

1

© 2022 Toyota Motor Sales, USA

Front Emergency Towing Eyelet

T-SB-0109-22

December 14, 2022

Page 7 of 11

2023 Mirai Pre-Delivery Service (PDS)
Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation (continued)

3. Install the front AND rear emergency
towing eyelet hole covers, which are stored
in the glove compartment, onto the front
and rear bumpers.

Figure 4.

B

A
1

A. Insert the arrow-shaped part “A” of the
front emergency towing eyelet hole
covers into eyelet holes “B” as shown.

B

B. Install the front and rear emergency
towing eyelet hole covers into the holes
of the front bumper.

A
2

A

Arrow-shaped Part

B

Eyelet Hole

1

Front Emergency Towing Eyelet Hole Cover

2

Rear Emergency Towing Eyelet Hole Cover

© 2022 Toyota Motor Sales, USA

T-SB-0109-22

December 14, 2022

Page 8 of 11

2023 Mirai Pre-Delivery Service (PDS)
Front Wheel Opening Extension Pad Installation

The front wheel opening extension pad set (right and left front wheel opening extension pads
and six self-tapping screws) is stored in the luggage compartment at the assembly plant to avoid
damage in transit.
1. Hook the retainers of the left front wheel
opening extension pad through the
installation holes on the fender liner and
temporarily place the left front wheel
opening extension pad in the
installation position.

Figure 5.

HINT

2

There is a distinguishable mark on each pad.

1

2. Tighten the three self-tapping screws.

3. Repeat steps 1 and 2 for the right side.

1

Self-tapping Screws

2

Front Wheel Opening Extension Pad

© 2022 Toyota Motor Sales, USA

T-SB-0109-22

December 14, 2022

Page 9 of 11

2023 Mirai Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation

The front license plate bracket and two self-tapping screws are stored in the vehicle. Follow this
procedure to install the front license plate bracket and front license plate in states where it is
required by law.
1. Align holes “A” of the mounting bracket
with the dimples on the radiator lower grille.

Figure 6.
1

NOTE
 Holes “A” are used for installation of the
mounting bracket to the radiator grille.
 Holes “B” are used for the installation of the
front license plate to the mounting bracket.

B

B
A

A

1
2

2. Screw the two self-tapping screws directly
into the dimples to install the front license
plate mounting bracket.
NOTICE
 Do NOT drill holes in the dimples.
 Do NOT overtighten the
self-tapping screws.
3

3. Install the mounting bracket to the radiator
grille using two self-tapping screws.

1

Mounting Bracket

2

Dimples

3

Self-tapping Screws

© 2022 Toyota Motor Sales, USA

T-SB-0109-22

December 14, 2022

Page 10 of 11

2023 Mirai Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)

4. Install the front license plate onto the mounting bracket at holes “B” using two noncorroding
bolts with the following dimensions:
Nominal Length: 15.0 mm (0.59 in.)
Diameter: 6.0 mm (0.24 in.)
Figure 7.

Figure 8.

1

2

2

1

3

1

Nominal Length

1

Front License Plate

2

Diameter

2

Mounting Bracket

3

Bolts

© 2022 Toyota Motor Sales, USA

T-SB-0109-22

December 14, 2022

Page 11 of 11

2023 Mirai Pre-Delivery Service (PDS)
Installation of Rubber Body Plugs

1. Confirm the number of plugs in the glove box. If two plugs are present, perform
substep 2A ONLY. If four plugs are present, perform substep 2A AND substep 2B.
2. Install plugs according to the instructions below by confirming the number of plugs in the
glove box.
A. Install two plugs in the rear side member hole or rocker inner hole as shown.
B. Install two plugs in the torque box hole or rocker inner hole as shown.
Figure 9.

1

2

z
6

3

6

1

Front Side

2

Rear Side

3

Torque Box Hole or Rocker Inner Hole

4

Rear Side Member Hole or Rocker Inner Hole

5

Rocker Inner

6

Install Plug Here (if Applicable)

z

5

z

z

z

4

z

z

NOTICE
 The installation of these plugs is required to prevent rust.
 These plugs are stored in the glove box.
 The number of plugs may vary according to production locations in the same
vehicle model.

© 2022 Toyota Motor Sales, USA