NHTSA ID Number: 10229077
Manufacturer Communication Number: S2209000003
TSB/Document Date: 2023-01-09
Summary
Complete Engine Assembly Replacements Arriving Without Engine Wiring Harness.
Case Number: S2209000003
Release Date: March 2022
Symptom/Vehicle Issue: Complete Engine Assembly Replacements Arriving Without
Engine Wiring Harness.
Discussion: Due to a shortage of wiring harnesses at the engine assembly plant, the following
replacement engine assemblies are temporarily being shipped without an engine wiring harness.
•
•
05158052AG – 2014-2019 Jeep
Grand Cherokee (WK)
05158048AF – 2019-2019 Ram 1500 (DS)
When installing the replacement engine, you will need to transfer the engine wiring harness from the
original engine, onto the new assembly. Please take care when removing the original engine and
harness to avoid any potential damage to the wiring harness.
The new engine assemblies will arrive partially disassembled to allow for easier installation of the
wiring harness. The remaining components needed to completely assemble the engine once the
harness is installed, will be in a separate kit supplied with the engine. The components included in
this kit are:
•
•
•
•
•
•
High Pressure Fuel Supply Lines for the following components
o Fuel Injectors 1, and 2 on the passenger side bank.
o Fuel Injectors 4, and 5 on the driver’s side bank.
o Fuel Rail Supply line, injection pump to passenger side rail.
Pipe Assembly, EGR valve to Intake Manifold.
Foam Pad, Injection pump impact cover
Injection pump impact cover.
Engine harness support bracket.
Associated nuts and bolts for installing the above components.
Please refer to the following repair procedure to install the original harness on the new engine
assembly.
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
Repair Procedure:
NOTE: Take care when removing the original engine from the vehicle, and wiring
harness from the original engine, to avoid damaging the harness.
NOTE: The open ports on the fuel system components (e.g. fuel rails, fuel
injectors, and fuel injection pump) will have protective caps installed to ensure
system cleanliness. To maintain fuel system cleanliness, do not remove these
protective caps until instructed to do so.
1. Once the original engine has been removed from the vehicle, carefully remove the engine wiring
harness.
2. Carefully lay the engine harness on top of the new engine.
3. Secure the wiring harness beauty cover over the stud on the passenger side valve cover. Please
see (Figure 1).
Figure 1.
4. Route the rear of the harness on the driver’s side, under the #6 fuel injector fuel line. Please see
(Figure 2).
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
Figure 2.
5. Secure the harness retaining clips to the appropriate studs and ensure the harness is over the fuel
return line. Fit the harness cover onto the valve cover studs. Please see (Figures 3&4). Take care
not to pinch the fuel return line.
Figure 3
Figure 4
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
6. Secure the front of the harness on the driver’s side, onto the studs as shown. Please see (Figure
5).
Figure 5
7. Connect the electrical connectors for the following components.
a. Oil pressure and temperature sensors.
b. Glow plugs 4, 5, and 6
c. Injectors 4, 5, and 6
d. Swirl valve/throttle body jumper harness connector.
e. Turbo VGT connector
f. Exhaust manifold pressure sensor.
8. Remove the associated protective caps and install the high-pressure fuel lines for injectors 4 and
5. Install the fuel line hand tight.
9. Connect the EGR Cooler, and Throttle Body Temperature sensor electrical connectors. Please
see (Figure 6).
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
Figure 6
10. Carefully disconnect the vacuum line from the vacuum pump fitting on the passenger side upper
timing cover and position it out of the way. Do not fully remove the vacuum line.
11. Remove the associated protective caps and install the high-pressure fuel supply line from the
injection pump to the passenger side fuel rail. Install the fuel line hand tight. Be sure to route the
fuel line under the harness and fuel return line.
12. Install the high-pressure fuel supply line retaining clamp to the valve cover stud with the supplied
nut, and secure hand tight. Please see (Figure 7).
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
Figure 7
13. Reinstall the vacuum line previously removed in step 10, onto the vacuum pump.
14. Secure the harness to the high-pressure fuel supply, and fuel injection pump supply lines.
Connect the electrical connectors for the FQS and Coolant Temperature Sensor. Please see
(Figure 8).
Figure 8.
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
15. Remove the associated protective caps, and install the high-pressure fuel lines on fuel injectors 1
and 2. Install hand tight.
16. Connect the electrical connectors for the glow plugs, and fuel injectors for cylinders 1, and 2.
17. Connect the electrical connectors for the EGR valve and EGR temperature sensor.
18. Install the supplied engine harness support bracket using the supplied M6 bolts and secure the
harness to the bracket. Please see (Figure 9). Tighten the bolts to 8 ft/lbs. (10.8 nm).
Figure 9
19. Tighten all high-pressure fuel line nuts for the fuel injectors and fuel rail supply line that were
installed hand tight. Torque the fuel line nuts in the following sequence.
a. Torque to 8 ft/lbs. (11 nm).
b. Torque to 30 ft/lbs (40 nm).
20. Torque the passenger side high-pressure fuel rail supply line retaining clamp nut to 8 ft/lbs. (10.8
nm).
21. Connect the electrical connectors for the #3 glow plug and fuel injector. Secure the harness to the
#3 fuel injector supply line. Please see (Figure 10).
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
Figure 10
22. Connect the electrical connectors for the following components.
a. Fuel rail pressure sensor.
b. CAC Inlet temperature sensor.
c. Boost pressure sensor
d. Passenger bank swirl valve position sensor.
23. Install the EGR cooler to intake manifold pipe assembly using the supplied M6 and M8 bolts.
Torque to the following:
a. M6 bolts (pipe to intake manifold connection). Torque to 8 ft/lbs. (10.8 nm).
b. M8 bolts (pipe to EGR cooler assembly connection). Torque to 18 ft/lbs. (24.5 nm).
24. Install the injection pump impact cover foam pad over the injection pump and install the injection
pump impact cover using the 4 M8x50 bolts. Torque the bolts to in the following sequence.
a. Torque to 8 ft/lbs. (10.8 nm).
b. Torque to 18 ft/lbs. (24.5 nm).
25. Continue with the installation of the engine.
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
NOTE: Once the engine installation is complete, please be sure to program the
new injector flow rate codes into the PCM via the wiTECH Injector Quantity Code
programming routine in PCM Misc. Functions. The new injector codes can be
found on the lower barcode sticker, on the injection pump impact cover. Please
see (Figure 11).
Figure 11
This document does not authorize warranty repairs. This communication documents a record of past experiences. STAR Online
does not provide any conclusions about what is wrong with the vehicle. Rather, it captures all previous cases known that appear
to be similar or related to the vehicle symptom / condition. You are the expert, and you are responsible for deciding on the
appropriate course of action.
Contact STAR Center, or your Technical Assistance Center Via TechCONNECT or eCONTACT ticket if no
solution is found
FCA US LLC
Version 4.3 10/29/2020
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: S2209000003
Replacement Service Bulletin Number:
MFR Communication Date: 2022-03-23
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM:SEAT HEATER:WIRING HARNESS
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations
- 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler
, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order - 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.