L-SB-0054-22

November 4, 2022

2023 LX 600 Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2023

LX600

ADDITIONAL INFORMATION

Introduction

This bulletin contains the vehicle specific pre-delivery services for 2023 model year LX 600
vehicles. Additionally, refer to the applicable Pre-Delivery Service (PDS) Check Sheet for
services to be performed.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

© 2022 Lexus, a division of Toyota Motor Sales, USA

Page 1 of 7

L-SB-0054-22

November 4, 2022

Page 2 of 7

2023 LX 600 Pre-Delivery Service (PDS)
Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

Techstream ADVi*
Techstream 2.0
Techstream Lite

PART NUMBER

QTY

TSADVUNIT
ADE

Techstream Lite (Green Cable)

TS2UNIT
TSLITEPDLR01

1

TSLP2DLR01

*Essential SST.

NOTE
 Only ONE of the Techstream units listed above is required.
 Software version 17.20.013 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787.

Procedures



D/C Cut Fuse (30A) Installation ............................................................................................... 3



Head Unit System Reset .......................................................................................................... 4



Seating Position Control ECU Initialization ............................................................................... 4



Installation of Towing Hitch Cover* .......................................................................................... 4



Front License Plate and Mounting Bracket Installation* ........................................................... 5



Tire Pressure Warning System Initialization ............................................................................. 7



Set Hybrid Radio Feature to Off ............................................................................................... 7



Navigation — Set Date & Time by GPS ................................................................................... 7

*If Applicable

© 2022 Lexus, a division of Toyota Motor Sales, USA

L-SB-0054-22

November 4, 2022

Page 3 of 7

2023 LX 600 Pre-Delivery Service (PDS)
D/C Cut Fuse (30A) Installation

To minimize battery discharge during transportation and storage, the D/C cut fuse (30A) has
been removed at the assembly plant and temporarily stored in the blank space of the relay block
in the engine compartment. During PDS, reinstall the D/C cut fuse (30A) to its original location
and confirm ALL related Diagnostic Trouble Codes (DTCs) are cleared.
Remove the D/C cut fuse (30A) from the blank space of the relay block in the engine
compartment and install the D/C cut fuse (30A) in the relay block as shown.
Figure 1.

1

3

2

1

Relay Block

3

2

Remove D/C Cut Fuse (30A)

Install D/C Cut Fuse (30A) (Original Location)

NOTE
With the D/C cut fuse (30A) removed, the diagnostic trouble code (DTC) is detected when the ignition
is turned on during transportation. Clear all DTCs using the GTS after checking that there are no
malfunctions on the vehicle.

© 2022 Lexus, a division of Toyota Motor Sales, USA

L-SB-0054-22

November 4, 2022

Page 4 of 7

2023 LX 600 Pre-Delivery Service (PDS)
Head Unit System Reset

Confirm that the welcome screen with language options appears on the head unit display when
ignition is switched to the ON position. There may be instances where the welcome screen with
language options may not properly appear on the head unit display.
If the welcome screen showing language options is NOT displayed, complete the
following steps:
1. Select the Settings option (gear icon).
2. Scroll down and select the Info & Security option.
3. The System Reset dialogue box will appear. Select Reset to confirm the resetting of
the system.
4. Confirm that the welcome screen with language options is displayed.

Seating Position Control ECU Initialization

Refer to the applicable Repair Manual for the seating position control ECU initialization
procedure (procedure 3).

Installation of Towing Hitch Cover

1. Attach the two provided clips to install the
towing hitch cover.

Figure 2.

1

2

1

Towing Hitch Cover

2

Clips

© 2022 Lexus, a division of Toyota Motor Sales, USA

L-SB-0054-22

November 4, 2022

Page 5 of 7

2023 LX 600 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation

The front license plate mounting bracket and two self-tapping screws are stored in the rear cargo
area of the vehicle. For states that require a front license plate, install the license plate and
mounting bracket during PDS.
1. Remove the two radiator grille mouldings
by disengaging the three claws on each.

Figure 3.

1

1

2. Attach the front license plate mounting
bracket hooks to the air intake of the
radiator grille and hold in place.

Radiator Grille Mouldings

Figure 4.

1

Align holes “A” of the mounting
bracket with the installation holes on
the radiator grille.
NOTE

2

 Holes “A” are used to install the
mounting bracket to the bumper cover.
 Holes “B” are used to install the front
license plate to the mounting bracket.

A

B
A

3

1

Mounting Bracket

2

Installation Holes

3

Hooks

© 2022 Lexus, a division of Toyota Motor Sales, USA

L-SB-0054-22

November 4, 2022

Page 6 of 7

2023 LX 600 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)

Install the mounting bracket to the radiator
grille using the two self-tapping
screws provided.

Figure 5.

NOTICE
Do NOT overtighten the
self-tapping screws.
2

1

4

Install the front license plate using two
noncorroding bolts with the
following dimensions:

3

2

1

Mounting Bracket

2

Self-tapping Screws

3

License Plate

4

Bolts

Figure 6.

Nominal Length: 15.0 mm (0.59 in.)
Diameter: 6.0 mm (0.24 in.)

2
1

1

Nominal Length

2

Diameter

© 2022 Lexus, a division of Toyota Motor Sales, USA

L-SB-0054-22

November 4, 2022

Page 7 of 7

2023 LX 600 Pre-Delivery Service (PDS)
Tire Pressure Warning System (TPWS) Initialization

Refer to the applicable Repair Manual for the TPWS initialization procedure. Note the spare tire
does NOT have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using Techstream and select the compensation tire pressure
checkbox. Compensation pressures will display on the Health Check results screen. Adjust the tire
pressure when the tires are cold.

Set Hybrid Radio Feature to OFF

Without a Wi-Fi subscription, the customer will receive a “Subscription Required” pop-up while in
weak broadcast radio signal areas. This pop-up notification may cause confusion to the customer.
Therefore, it is necessary to toggle the Hybrid Radio feature to the OFF position.
1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Navigate the following menus in the head unit: Settings – Sound and Media – Radio –
Hybrid Radio.
3. Ensure the Hybrid Radio feature is set to the OFF position.
NOTE
The Enable Hybrid Radio feature is factory preset to the ON position.

Navigation — Set Date & Time by GPS

Before selling a Toyota vehicle, it is necessary to turn the Set Date & Time by GPS setting to the
ON position.
1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Navigate the following menus in the head unit: Settings – General – Date & Time –
Set date & time by GPS.
3. Ensure the Set Date & Time by GPS function is set to the ON position.

© 2022 Lexus, a division of Toyota Motor Sales, USA