Page 1 of 3

TECHNICAL BULLETIN
LTB00409NAS4
25 OCT 2013
© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools,
and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some
vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-ityourselfers'. If you are not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land
Rover service facility to determine whether this bulletin applies to a specific vehicle.

This reissue replaces all previous versions. Please destroy all previous versions. Only refer to the
electronic version of this Technical Bulletin in TOPIx.

SECTION: 303-04

Engine Misfires / Engine MIL Illuminated
AFFECTED VEHICLE RANGE:
LR4 (LA)
Model Year:
VIN:

2010-2013
AA510742-DA699999

Range Rover Sport (LS)
Model Year:
2010-2013
VIN:
AA212147-DA814882
Range Rover (LM)
Model Year:
2010-2012
VIN:
AA304426-CA363639

MARKETS:
NAS

CONDITION SUMMARY:
Situation:

NOTE: This bulletin supersedes all previous versions; the Service Instructions have changed
significantly and are therefore not highlighted.
The engine may exhibit a misfire, poor fuel economy, hard starting, and / or a rough idle condition. The engine
Malfunction Indicator Lamp (MIL) may also be illuminated with misfire Diagnostic Trouble Codes (DTC) P0301
through P0308 and P0316, depending on the affected cylinder(s), stored in the Engine Control Module (ECM).

Cause: This may be caused by incomplete combustion caused by poor fueling.

NOTE: The Service Instruction may only be completed if no other causes for the misfire are
identified after following SDD and TOPIx advice.

NOTE: The Service Instruction may only be completed if Diagnostic Trouble Code (DTC) P0316
and one or more misfire DTCs (P0301-P0308) is stored. If any other DTC is stored, investigate the
cause and carry out the appropriate repair as a separate claim.
Action: Should a customer express this concern, follow the Service Instruction outlined below.

PARTS:

http://topix.landrover.jlrint.com/topix/service/document/442376

10/28/2013

Page 2 of 3

LR037088

Fuel injector

Quantity: Up to 8 (as
required)

TOOLS:

NOTE: This document is an 'Active Bulletin' that will display a functional programming shortcut if
accessed within a diagnostic session using SDD.

SDD with latest DVD and Calibration File; first available on DVD135.03 v.147
Jaguar Land Rover-approved Midtronics battery power supply

WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair
time.
NOTE: DDW requires the use of causal part numbers. Labor only claims must show the causal part
number with a quantity of zero.
DESCRIPTION

SRO

TIME
(HOURS)

CONDITION
CODE

CAUSAL
PART

Update Engine Control Module software

12.90.13

0.2

42

LR037088

Fuel rail/injector(s) - Right bank - Renew - LR4

19.60.11

3.2

42

LR037088

Fuel rail/injector(s) - Left bank - Renew - LR4

19.60.09

2.9

42

LR037088

Fuel rail/injector(s) - Both banks - Renew - LR4

19.60.12

5.7

42

LR037088

Fuel rail/injector(s) - Right bank - Renew - Range
Rover Sport

19.60.11

3.2

42

LR037088

Fuel rail/injector(s) - Left bank - Renew - Range
Rover Sport

19.60.09

2.9

42

LR037088

Fuel rail/injector(s) - Both banks - Renew - Range
Rover Sport SC

19.60.12

5.7

42

LR037088

Fuel rail/injector(s) - Both banks - Renew - Range
Rover Sport N/A

19.60.12

5.6

42

LR037088

Fuel rail/injector(s) - Right bank - Renew - Range
Rover SC

19.60.11

2.1

42

LR037088

Fuel rail/injector(s) - Right bank - Renew - Range
Rover N/A

19.60.11

1.7

42

LR037088

Fuel rail/injector(s) - Left bank - Renew - Range
Rover SC

19.60.09

1.4

42

LR037088

Fuel rail/injector(s) - Left bank - Renew - Range
Rover N/A

19.60.09

1.2

42

LR037088

Fuel rail/injector(s) - Both banks - Renew - Range
Rover SC

19.60.12

3.2

42

LR037088

Fuel rail/injector(s) - Both banks - Renew - Range
Rover N/A

19.60.12

2.7

42

LR037088

NOTE: Normal Warranty policies and procedures apply.

SERVICE INSTRUCTION:

NOTE: The Service Instruction may only be completed if Diagnostic Trouble Code (DTC) P0316 and
one or more misfire DTCs (P0301-P0308) is stored. If any other DTC is stored, investigate the cause and
carry out the appropriate repair; to be performed as a separate claim.

http://topix.landrover.jlrint.com/topix/service/document/442376

10/28/2013

Page 3 of 3

1.

NOTE: If the Freeze frame data indicates a 'cold' engine misfire only, do not replace fuel
injectors; continue to step 3.

NOTE: A printed copy of the Freeze frame data, indicating engine coolant temperature at the
time of the engine misfire, must be kept in the vehicle record file.
View the Freeze frame data for Diagnostic Trouble Code (DTC) P0316 or one misfire DTC (P0301-P0308) and
read the engine coolant temperature.
If the engine coolant temperature is 76ºC or higher ('hot' engine), continue to step 2.
If the engine coolant temperature is 75ºC or lower ('cold' engine), continue to step 3; do not replace fuel

injectors.
2. If Diagnostic Trouble Code (DTC) P0316 and one or more misfire DTCs (P0301-P0308) is stored and no other
misfire cause is found, replace the affected fuel injector(s) as indicated by the DTC (see TOPIx Workshop
Manual, Section 303-04).
Once completed, continue to step 3 below.

3.

CAUTION: A Jaguar Land Rover-approved Midtronics battery power supply must be connected
to the vehicle battery during SDD diagnosis / module programming.

NOTE: SDD must be loaded with DVD135.03 v.147 or later.
Connect the Jaguar Land Rover-approved Midtronics battery power supply to the vehicle battery.

NOTE: The Engine Control Module (ECM) may also be referred to as Powertrain Control Module
(PCM).

4. Turn ignition 'ON' (engine not running).
5. Connect the Symptom Driven Diagnostics (SDD) system to the vehicle and begin a new session.
6. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle and initiating the data
collect sequence.
7. Select 'Diagnosis' from the Session Type screen.
8. Select the 'Selected Symptoms' tab, and then select one of the following:
Powertrain - Engine system - Engine performance - Engine misfire or
Electrical - Instruments - Warning lamps - Engine malfunction lamp - Lamp illuminated or
Electrical - Instruments - Information and Message Centre - Message Display Area - Powertrain

9. Select 'continue'.

10.
NOTE: The Engine Control Module (ECM) may also be referred to as Powertrain Control
Module (PCM).
Select the 'Recommendations' tab, and then select 'Run' to perform the 'Configure existing module –
Powertrain control module' option.
11. Follow all on-screen instructions to complete this task.
12. Exit the current session.
13. Disconnect the SDD and the battery power supply from the vehicle.

http://topix.landrover.jlrint.com/topix/service/document/442376

10/28/2013