Technical Service Bulletin
PSS 01 MIL on, fuel rail pressure low (P0087)
01 13 82 2033211/4 March 28, 2013. Supersedes Technical Service Bulletin Group 01 number 13-81 dated
March 28, 2013 for reasons listed below.

Model(s)

Year

VIN Range

Vehicle-Specific Equipment

A4, allroad, A5,
A5 cab, Q5, A6

2013

All

2.0 TFSI

Condition
REVISION HISTORY
Revision

Date

Purpose

4

-

Revised Customer Q&A attachment

3

3/28/2013

Revised Service (Modified steps)
Added attachment (Customer Q&A)

2

3/12/2013

Revised header data (corrected VIN range)

1

3/5/2013

Initial publication

Customer may report MIL on and loss of performance.

Technical Background
Under extreme driving conditions (e.g. long idle periods or extended stop and go traffic), high temperatures can
build up in the rail system and may lead to fluctuations in fuel pressure, possibly causing DTC P008700 (fuel rail
pressure too low) to be stored. Coolant temperature above 102˚C in the freeze frame data can be an indicator of
those extreme driving conditions.

Production Solution
Software to optimize the cooling strategy to solve this issue is currently in development.

Page 1 of 3 plus attachment
© 2013 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
Service
1. Diagnose the vehicle according to the instructions listed below. If customer’s vehicle
condition matches the condition listed in the Technical Background of this PSS TSB,
continue with the points below.
2. Create a PSS record in
the PSS application via
the hyperlink in
Accessaudi.com
(Figure 1) or Technical
Assistance page in
Elsa (Figure 2).

Figure 1. Related Sites section on Accessaudi.com landing page

Figure 2. Technical Assistance page
3. Open a TACS ticket and call TACs for further instructions.
Condition verification procedure
Reproduce the condition:
1. Ensure that the air conditioning is switched off.
2. Allow the engine to warm up until the radiator fans start running.
3. Shut down the vehicle immediately to create heat build-up.

Page 2 of 3 plus attachment
© 2013 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
4. Allow the vehicle to sit for five minutes, then start a test drive.
5. Check if DTC P008700 is stored.
After verifying the condition, erase DTCs.

Warranty
Claim Type:

Use applicable claim type. If vehicle is outside any warranty, this Technical Service
Bulletin is informational only.

Service Number:

2441

Damage Code:

0015

Labor Operations:

Warm up vehicle

2441 0399

10 TU

Diagnostic Time:

GFF - Checking and clearing fault codes

0150 0000

Time stated on
diagnostic
protocol (Max 20
TU)

Road test after service procedure

0121 0004

10 TU

Claim Comment:

As per TSB #2033211/4

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.

Required Parts and Tools
Not applicable

Additional Information
All parts and service references provided in this TSB are subject to change and/or removal. Always check with
your Parts Department and service manuals for the latest information.

Page 3 of 3 plus attachment
© 2013 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Customer Q & A

Q: Why do I need to leave the A/C on auto?
A: Leaving the A/C on auto will activate radiator fans on low speed, allowing lower
temperatures in the engine bay and minimizing fuel pressure fluctuations through heat
buildup.
Q: I need my vehicle to heat, why would I have the A/C on?
A: Turning the A/C on auto will not prevent the system from producing heat. It will still
regulate to the set temperature and provide heat if necessary to reach that temperature. It
will also dehumidify the air to prevent fogging of the windows.
Q: Will I experience performance issues again?
A: Having the A/C on auto is currently the most effective way to prevent this issue from
happening. A permanent solution is currently being developed; your dealer will contact you
as soon as it is available. Resolving the concern and providing a solution is Audi’s highest
level of priority.
Q: I want to use settings other than auto for the climate control. Can I do that?
A: You can use other settings for climate control as long as the LED for A/C is illuminated
(Figure 1).

Figure 1: Climate control with A/C LED on