NUMBER:
GROUP:
DATE:

08-060-16
Electrical
May 11, 2016

This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

SUBJECT:
Electronic Parking Brake Module Connector Water Intrusion
OVERVIEW:
This bulletin involves inspecting the parking brake module wiring harness connection for
terminal corrosion and if needed, replacing the connector.
MODELS:
2014 - 2016

(KL)

Jeep Cherokee

NOTE: This bulletin applies to vehicles within the following markets/countries:
NAFTA.
NOTE: This bulletin applies to vehicles built on or before February 15, 2016 (MDH
0215XX).
SYMPTOM/CONDITION:
The customer may describe that the Electronic Parking Brake (EPB) may not release and
a service message is present with a Malfunction Indicator Lamp (MIL) illumination. Upon
further investigation the technician may find one or more of the following Diagnostic
Trouble Codes (DTCs):
•
•
•

C008E-00 - ECU Internal Performance.
C10CD-01 - Electronic Park Brake Switch - General Electrical Failure.
C10ED-00 - Electronic Park Brake Switch LED.

DIAGNOSIS:
Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in
TechCONNECT, verify all engine systems are functioning as designed. If DTCs or
symptom conditions, other than the ones listed above are present, record the issues on the
repair order and repair as necessary before proceeding further with this bulletin.
If the customer describes the symptom/condition listed above or if the technician finds the
DTC, perform the Repair Procedure.

08-060-16

-2-

PARTS REQUIRED:
Qty.

Part No.

Description

1

68256811AA

Module, Electronic Parking Brake Connector

1 (AR)

68265141AB

Module, Electronic Parking Brake
2015 - 2016 (KL)

1 (AR)

68148902AE

Module, Electronic Parking Brake
2014 (KL)

REPAIR PROCEDURE:
1. The Electronic Parking Brake (EPB) module is located in the back left side of the cargo
area interior, near the spare tire (Fig. 1) and is attached by a slide locking retainer and
fastener.

Fig. 1 Location of EPB Module
1 - Storage Bin
2 - EPB Module Location (Shown with Load floor Support Removed)

2. Remove EPB module hold down nut.

-3-

08-060-16

3. Remove the storage bin and pull EPB Module and connector through opening (Fig. 2).

Fig. 2 Pull EPB Module and Connector Through Cutaway For Inspection
1 - EPB Module and Connector Pulled Through Cutaway

4. Remove the connector and inspect for terminal corrosion (Fig. 3).

Fig. 3 Connector Face Inspection
1 - Check Connectors for Corrosion

08-060-16

-4-

5. Is there evidence of corrosion on the terminal(s)?
a. YES>>> Proceed to Step #6.
b. NO>>> This Bulletin does not apply. Normal diagnosis should be performed.
6. Remove interior trim panels to allow access to the harness for EPB connector pigtail
replacement (Fig. 4).

Fig. 4 Interior Trim Panels Removed For Access
1 - Wire/Cable Hold-down
2 - EPB Module

7. Replace EPB Module and connector.
CAUTION: The orange and yellow wires are a twisted pair for shielding purposes,
take care to continue twist and at the same rate for the orange and yellow
wires.
8. Perform EPB verification test Refer to the detailed service procedures available in
DealerCONNECT> TechCONNECT under: Service Info> 28 - DTC-Based
Diagnostics>MODULE, Electronic Park Brake (EPB)>Standard Procedure>EPB
VERIFICATION TEST).
NOTE: If this Electronic Control Unit (ECU) is being replaced with a new unit, a
diagnostic scan tool MUST be used to align the PROXI configuration data
into the new ECU. Follow the routine outlined in the diagnostic scan tool for
PROXI Configuration Alignment, under Body Control Module (BCM)
“Miscellaneous Functions” menu.
9. Clear all DTCs that may have been set. The wiTECH application will automatically
present all DTCs after the flash and allow them to be cleared.

-5-

08-060-16

POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation
No:

Description

Skill Category

Amount

08-19-85-90

Inspect Electronic Parking Brake
Module (EPB) Wiring Harness
Connector for Corrosion
(2 - Skilled)

6 - Electrical
and Body
Systems

0.3 Hrs.

08-19-85-91

Replace Electronic Parking Brake
Module (EPB) Wiring Harness
Connector
(2 - Skilled)

6 - Electrical
and Body
Systems

1.7 Hrs.

FAILURE CODE:
ZZ

Service Action