Technical Service Bulletin
87 Air Conditioning is inoperative, DTC B11AE15
87 22 32 2067362/2 September 20, 2022. Supersedes Technical Service Bulletin Group 97 number 22-84 dated
June 22, 2022,
for reasons listed below.

Model(s)

Year

Q8

2020 – 2023

SQ8, and RS Q8

2021 - 2023

VIN Range

Vehicle-Specific Equipment

All

Not Applicable

Condition
REVISION HISTORY
Revision

Date

Purpose

2

-

Revised Required Parts and Tools (updated part number for tape)

1

06/22/2022

Initial publication

Customer states:
• Customer states the A/C is inoperative and does not cool the vehicle.
Workshop findings:
The following DTC is stored in the onboard supply control unit J519 diagnostic address 0009.
•

DTC B11AE15: A/C compressor regulator valve, open circuit/short circuit to B+.

Page 1 of 5
© 2022 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to
other sites, without the prior expressed written permission of the publisher.

Technical Service Bulletin
Technical Background
The wiring to the A/C compressor connector T3r is not long enough. Wires may become stretched, broken, or
pulled from the connector as a result.

Production Solution
Harness length increased in production.

Service
If DTC B11AE15: A/C compressor regulator valve Open circuit/short circuit
to B+ is stored in the onboard supply control unit J519 diagnostic address
0009, inspect the wiring at connector T3r in the area of the A/C
compressor as seen in Figure 1.

Tip: It may be necessary to cut back the harness tape several inches
to expose the damaged section of the harness.

Figure 1. N280 control wire damaged
at T3r connection
If damage is found in this area, all 3 wires will need to be extended
following the directions below.

Page 2 of 5
© 2022 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to
other sites, without the prior expressed written permission of the publisher.

Technical Service Bulletin
1. Cut back the damaged wire(s) until the wires are clean and free of any
corrosion.
2. Extend all 3 wires so that a length of approximately 110mm is achieved
when measuring from the base of the connector to the first branch in
the harness. See Figure 2.
3. Ensure there is enough slack to keep the harness from stretching
however not so much the wires hang down.
4. Repair and modify the harness using VAS 1978 B.
5. Wrap the harness section using fabric adhesive tape N 105 920 02.
Wrap wires up to 20mm from the base of the connector housing, as
seen on the original harness in Figure 1.
6. Clear faults and perform a functional check.

Figure 2. Measure 110 mm from T3r
to the first harness branch

Warranty
Claim Type:

• 110 up to 48 Months/50,000 Miles.
• G10 for CPO Covered Vehicles – Verify Owner.
• If the vehicle is outside of any warranty, this Technical Service Bulletin is
informational only.

Service Number:

9712

Page 3 of 5
© 2022 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to
other sites, without the prior expressed written permission of the publisher.

Technical Service Bulletin
Damage Code:

0015

Labor Operations:

Remove and install noise 10 82 19 00

See SRT with associated

insulation

operations

Repair wiring harness

97 09 41 53

See SRT with associated
operations

Diagnostic Time:

GFF

0150 0000

Time stated on the
diagnostic protocol (Max
50 TU)

Road test prior to the

No allowance

0 TU

No allowance

0 TU

service procedure
Road test after the
service procedure
Claim Comment:

As per TSB 2067362/2

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures

Manual. Claims are subject to review or audit by Audi Warranty.

Required Parts and Tools
Always check with your Parts Department and/or ETKA for the latest information and
parts bulletins.
Part Number

Part Description

Quantity

Page 4 of 5
© 2022 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to
other sites, without the prior expressed written permission of the publisher.

Technical Service Bulletin
See ETKA

Fasteners, Bolts, Nuts, and Screws as

See ETKA/ELSA

needed per the Repair Manual
000 979 940

crimp connectors

03

000 979 025 E

individual wires

0.3 (only charge 2 wires
from the pack of 5)

N 105 920 02

Fabric adhesive tape

0.2

Additional Information
All part and service references provided in this TSB (2067362) are subject to change and/or removal. Always check
with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the Repair
Manual for fasteners, bolts, nuts, and screws that require replacement during the repair.
©2022 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes at any time
without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be
modified or reposted to other sites, without the prior expressed written permission of the publisher.

Page 5 of 5
© 2022 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property
rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to
other sites, without the prior expressed written permission of the publisher.