mm/ 8.46 in

Figure 15

Dimension X1-ST = distance from corner of spoiler (right) / downwards (rear
window, right edge): Length 30 mm/ 1.18 in
Dimension X-ST = distance from lower edge of rear window / upwards to rear
camera base (bottom right corner): Length 364 mm/ 14.33 in

Tequipment

Aug 23, 2022
Page 13 of 27

9

Panamera (971)
9163

ENU

Installation and Conversion Instructions

12/22

Dimension Z-ST = distance from rear window (right edge) / to the left to the rear
camera base (bottom right corner): Length 208 mm/ 8.19 in

3.3

3.2.2

Install rear camera base on the outside of the rear window.

3.2.3

Trace and hatch the outline of the rear camera base using a grease stick/chalk. 
Figure 15 -3-

Sticking on privacy film
3.3.1

Clean bonding area for rear camera (marking) on the inside of the rear window to
remove any dust and grease.

3.3.2

Pull 3M privacy film (rear camera)
off the backing sheet.  Figure 16
(Example Sport Turismo) -A1
2

3.4

– 3M privacy film (rear
camera)
– Marked bonding surface

3.3.3

Position 3M privacy film on the
marked bonding surface on the
windscreen inside ( Figure 16
(Example Sport Turismo) -B-) and
glue it on.

3.3.4

Carefully affix 3M privacy film using
a plastic squeegee, starting from
the center and moving towards the
edge.

Installing rear camera on rear window
3.4.1

Insert jack plug for wire harness into
rear camera ( Figure 17 -Arrow-)
and position line in cable duct.
1
2
3
4

3.4.2

Figure 16 (Example Sport Turismo)

– Connector with wire
harness
– Rear camera
– Cable duct
– Protective film

Pull protective film ( Figure 17
-4-) off the rear camera base.
Figure 17

Aug 23, 2022
Page 14 of 27

Tequipment

Installation and Conversion Instructions
3.4.3

12/22

ENU

9163

9

Align rear camera symmetrically
with respect to the 3M privacy film
on the inside of the rear window,
install it and press it firmly onto the
rear window.  Figure 18 (Example
Sport Turismo)
1
2
3

3.5

Panamera (971)

– Rear camera
– Connector with wire
harness
– Wrap clip (ONLY Sport
Turismo)

Basic/Executive vehicle: Route and
connect wire harness

Figure 18 (Example Sport Turismo)
Line routing:  Figure 19
1
2
3
4
5
•

–
–
–
–
–

Rear camera
Wire harness
Power supply
Video signal
Video signal plug connection holder

Rear camera → rear window frame (top)
→ along rear window frame (right-hand
side, viewed in direction of travel) →
power supply pre-fitting → video signal
pre-fitting

3.5.1

Route wire harness along the
existing lines for the rear camera
pre-fitting (underneath rear
window).
Figure 19

Tequipment

Aug 23, 2022
Page 15 of 27

9

Panamera (971)
9163

ENU

Installation and Conversion Instructions

12/22
3.5.2

Connect plug connection for power
supply pre-fitting (underneath rear
window).  Figure 20 -11
2
3
4

3.5.3

3.6

– Power supply
– Video signal plug
connection
– Holder
– Dummy plug

Remove video signal plug
connection from holder and remove
dummy plug.  Figure 20

Figure 20

3.5.4

Connect plug connection for video signal pre-fitting and install it in the holder.

3.5.5

Secure routed wire harness to
existing lines/components in the vehicle with tie-wraps without tensile stress and
so that no chafing occurs.

Sport Turismo vehicle: Route and connect
wire harness
Line routing:  Figure 21
1
2
3
4
5
6
•

–
–
–
–
–
–

Rear camera
Wire harness
Power supply
Video signal
Tie-wrap holder
Wrap clip

Rear camera → rear window frame (top)
→ power supply pre-fitting → video
signal pre-fitting

Figure 21

Aug 23, 2022
Page 16 of 27

Tequipment

Installation and Conversion Instructions
3.6.1

Panamera (971)
12/22

ENU

9163

9

Carefully remove the power supply
retaining clip and video signal
retaining clip from the tailgate and
guide it outwards out of the rear lid
cavity.  Figure 22
1
2
3
4

– Retaining clip for power
supply
– Retaining clip for video
signal
– Dummy plug
– Wrap clip

3.6.2

Secure wire harness for rear
camera to the tailgate frame using
wrapping clip and insulating tape.
 Figure 22 -4-

3.6.3

Connect plug connection for power
supply pre-fitting.

3.6.4

Remove video signal plug connection from holder and remove dummy plug (
Figure 22 -3-).

3.6.5

Connect plug connection for video signal pre-fitting and installing it in the holder.

3.6.6

Position both lines in the rear
lid cavity and install the relevant
retaining clip into the tailgate.
 Figure 23
1
2
3
4

3.6.7

Figure 22

– Retaining clip for power
supply
– Retaining clip for video
signal
– Tie-wrap holder
– Y-splitter

Install tie-wrap ( Figure 23 -3-) in
the cut-out in the tailgate. Secure
the remaining line in the Y-splitter area with a tie-wrap.

Figure 23

Secure the remaining line in the Y-splitter area with a tie-wrap.
4

Concluding work in vehicle interior
4.1

Rear lid area
4.1.1

Make groove for wire harness for rear camera in trim panel for window frame at the
center.

Tequipment

Aug 23, 2022
Page 17 of 27

9

Panamera (971)
9163

ENU

Installation and Conversion Instructions

12/22
4.1.2

ONLY for Basic/Executive:
•
•

4.1.3

Install trim panel for center window frame.
Install trim panel for rear lid, bottom.

Install trim panel for center window frame.  Workshop Manual '709219
Removing and installing trim panel for rear lid'

4.2

Install (front) roof console.  Workshop Manual '708319 Removing and installing front roof
console'

4.3

Protecting front and rear cameras against short circuits and overload damage ( Figure 24)
4.3.1

Move the left front seat as far back as possible in the fore-and-aft position. Set seat
height to maximum.

4.3.2

Expose fuse carrier under the left
front seat by folding over the carpet
cover you just cut out.
1
2
3
C

4.3.3

–
–
–
–

Carpet cover
Fuse carrier
Fuse, 5A
Fuse strip C

Insert slot 1 into fuse strip C = C1
( Figure 24 -3-) with a new fuse.
Setpoint value 5 A

Coding:

5

Coding PORSCHE front and rear cameras in dealer
mode

Figure 24

Aug 23, 2022
Page 18 of 27

Tequipment

Installation and Conversion Instructions
5.1

12/22

ENU

9163

9

Preparatory work
1
2
3
4
5
6

5.2

Panamera (971)

–
–
–
–
–
–

PORSCHE front camera
Micro SD memory card (32 GB)
Retainer plate
Power button
WiFi status LED display
PRESS (release button)

5.1.1

Remove micro SD memory card (32
GB,  Figure 25 -2-) from card slot
for front camera.

5.1.2

Figure 25
With the ignition switched on, push
the front camera (dashcam  Figure 25 -1-) on to the retainer plate on the windscreen ( Figure 25 -3-).

5.1.3

Press the power button ( Figure 25 -4-) for 10 seconds until you hear the second
double beeping sound.