Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

Condition
Applicable Vehicles
Model(s)

Year

Eng. Code

Trans. Code

VIN Range
From

VIN Range To

All

2006-2008

2.0T

All

All

All

All

All

All

(BPY)
All

2008-2017

2.0T
(CCTA/CBFA)

Revision Table
Instance Number

Published Date

Version Number

2045138/11

8/25/2022

24-18-01

Update to Warranty
table labor operation
numbers per SAGA
updates.

2045138/10

9/2/2021

24-18-01

To update applicable
model year.

2045138/1

1/4/16

V241701

Original publication.

DTC

Reason For Update

Description

P2004

Intake Manifold Flap for Air Flow Control Bank 1
Stuck Closed

P2014

Intake Manifold Runner Position Sensor/Switch
Circuit

P2015

Sender for Intake Manifold Flap Position/Air Flow
Control, Implausible Signal

Page 1 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

Technical Background
Perform 2 inspections before replacing the intake manifold.
Tip:
An ODIS intake manifold adaptation process must be performed after intake manifold replacement.
Inspection 1:
Vacuum line and vacuum tee restrictions (CCTA/CBFA).
Vacuum lines and “T” fittings may become clogged with debris from production or increasing mileage.
This debris may cause a restriction that could affect the intake manifold operation and cause DTC P2014,
P2015 faults.
Inspection 2:
Intake Manifold flap (BPY/CCTA/CBFA).
The intake manifold flap can separate internally and will not operate correctly with the regulator valve.
See Figure 1. and Figure 2. for an example of a damaged flap disassembled.

Figure 1.

Page 2 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

Figure 2.

Production Solution
Improved intake manifold design.

Service
Procedure 1:
Vacuum line and vacuum tee restrictions.
Ensure correct intake manifold is installed on engine, refer to ETKA.
The intake manifold runner can be checked for proper operation using MVB 143 field 3.
The vehicle must be driven in order to place a load on the engine.
The engine RPM should be quickly increased to at least 3000 RPM and released. MVB 143 field 3 value
should immediately change from 0% up to 100%.
If the values in field 3 instantly change to 100%, the hose and fittings are not restricted. If no restriction
has been identified, Continue procedure 2 diagnosis.
If there is a restriction, the values in field 3 will slowly increase or not increase at all. Inspect vacuum lines
leading to intake manifold, and fittings, for restrictions (twisted, kinked hoses or blockages caused by
debris).
Reposition or clean as required.

Page 3 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

Procedure 2:
Intake Manifold flap.
Check intake manifold flaps and if necessary replace intake manifold.
 Remove the engine cover. See Repair Group 10 Engine Assembly in Elsa.
 Move the carrier plate by hand in an axial direction (Figure 3, red arrow) to check if the carrier plate
can be pulled out.

Figure 3.

If the carrier plate can be pulled out, the flap has separated and the intake manifold must be replaced.
See Repair Group 24 Multiport Fuel Injection in Elsa.

If the carrier plate cannot be pulled out, perform the following procedure:
 Check the diagnostic limits of the flap with the ODIS tester.
 Under Motor, select Guided Functions (Figure 4).

Page 4 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

Figure 4
 Select Adapting Engine Control Module (ECM) to intake manifold flap (Figure 5).

Figure 5
Page 5 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

If the adaptation is not successful, the flap stop is worn internally, the intake manifold also has to be
replaced. See Repair Group 24 Multiport Fuel Injection in Elsa.
Note:
The new intake manifold will come with a new style Solenoid Valve for Intake Manifold Flap -N316. Please reference TB 2047363 for installation of Clean Air Line.

Note:
If no carrier plate, vacuum line or vacuum tee related damage is identified, and the adaptation
passes, diagnose the faults using guided fault finding. This bulletin does not apply.
Note:
During intake manifold replacement, all fuel injector seals must be replaced, see Elsa for installation
instructions.
After performing Intake Manifold Replacement, add fuel additive G 001780M3 to the fuel tank. Also, refer
the customer to brochure 2020 VW Top Tier Fuel (VWTOPTIERMAY20) and explain the benefits of using
Top-Tier fuels as indicated in Technical Bulletin 2014815.

Page 6 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

Warranty
To determine if this procedure is covered under Warranty, always refer to the Warranty Policies
and Procedures Manual 1)
Model(s)

Year(s)

Eng. Code(s)

Trans.
Code(s)

VIN Range
From

VIN Range To

All

2006-2008

2.0T

All

All

All

All

All

All

(BPY)
All

2008-2017

2.0T
(CCTA/CBFA)
SAGA Coding

Claim Type:

Use applicable Claim Type 1)

Service Number:

2447

Damage
Code
0010

Parts Manufacturer
Labor Operation 3) : Charge Battery

HST

Damage Location
(Depends on Service
No.)

--

--

All

MHO 2)

27068950 = See Elsa for latest time units

Labor Operation 3) : Inspection and/or repair 24474199 = 30 TU
hose
Labor Operation 3) : Remove + Reinstall
Fuel Injectors (Seal Replacement).

244019XX = See Elsa for latest time units

Labor Operation 3) : Intake Manifold
Replace

244755XX = See Elsa for latest time units (if applicable)

Labor Operation 3) : Install Clean Air Line

24662399 = 20 TU

Causal Part: Intake Manifold

XXX 133 XXX X (BPY)
XXX 133 XXX XX (CCTA, CBFA)

Outside Material: 2020 VW Top
Tier Fuel Brochure

VWTOPTIERMAY20

$1.50

Page 7 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

Diagnostic Time 4)
GFF Time expenditure

01500000 = Actual GFF print out

Road Test

01210002 = 10 TU
01210004 = 10 TU

Technical Diagnosis

01320000 = 10 TU max.

YES
YES
YES

Claim Comment: Input “As per Technical Bulletin 2045138” in comment section of Warranty Claim.
1)

Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only.

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policies and Procedures Manual.

Required Parts and Tools
Part No:

Part Description

Quantity

06F 133 201 P (BPY)

Intake Manifold

1 (If Necessary)

06D 998 907 (BPY)

Seals

4 (If Necessary)

06F 129 717 D (BPY)

Gasket

1 (If Necessary)

06J 133 201 BH (CCTA/CBFA)

Intake Manifold

1 (If Necessary)

06J 998 907 *

Seals

4 (If Necessary)

Flat- headed Screw with Torx
(thread cutting)

1

Clean Air Hose

1

06E 127 065 G

Adapter

2 (If Necessary)

06F 129 717 D (CCTA/CBFA)

Gasket

1 (If Necessary)

(CCTA/CBFA)
N 107 732 01
(CCTA/CBFA)
06H 133 583 F
(CCTA/CBFA)

Page 8 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Technical Service Bulletin

24-18-01 - MIL ON DTCs P2004, P2014 and or P2015 Stored in
Engine/Motor Control Module -J623-

Transaction No:

2045138/11

Release date:

8/25/2022

G 001780M3

Injector Cleaner

1

VWTOPTIERMAY20

2020 VW Top Tier Fuel Brochure

1

Part numbers are accurate at time of publication. Always refer to ETKA for the latest part information.
Tip:
Additional copies of the Top Tier fuel brochure may be ordered from Volkswagen Technical Literature
Ordering Center at https://literature.vw.com/

Tool Description

Tool No:

Midtronics Battery Tester/Charger

GRX3000VAS
or
MTRMSP0702 battery maintainer/charger

VAS Diagnostic Tool

VAS 6150/X & VAS 6160/X and
ODIS Service with: current online updates

Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.

Page 9 of 9
© 2022 Volkswagen Group of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and
other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.