Classification:

Reference:

BT22-006A

Date:

NTB22-024A

May 19, 2022

VOLUNTARY SERVICE CAMPAIGN
2013-2018 ALTIMA SEDAN;
FRONT COMBINATION LAMPS (HEADLAMPS) INSPECTION
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

CAMPAIGN ID #:
APPLIED VEHICLES:
APPLIED SYSTEMS:

PC861
2013-2018 Altima Sedan (L33)
Front Combination Lamps (Headlamps) – Halogen ONLY

Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.

INTRODUCTION
Nissan is conducting this voluntary service campaign on certain specific model year
2013-2018 Altima sedan vehicles, to inspect and, if necessary, replace both combination
(headlamp) assemblies (Halogen only). This service will be performed at no charge to the
customer for parts or labor.

IDENTIFICATION NUMBER
Nissan has assigned identification number PC861 to this campaign. This number must
appear on all communication and documentation of any nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/8

SERVICE PROCEDURE

1.

Open the driver (LH) side door.

2.

Set the parking brake.

3.

Start the engine.

4.

Turn the headlamps ON using the
combination switch.


Ensure the low beams are ON,
high beams are OFF.



If equipped, turn the fog lights
OFF.
Figure 1

5.

Clean both front headlamp assemblies
using clean water and a clean, soft car
towel.

Figure 2

2/8

NTB22-024A

Inspect Both Headlamps Low Beam Light Pattern
HINT: To help highlight the headlamp low beam light pattern on the headlamp lenses, you
can spray both headlamp assemblies with Nissan Foaming Glass Cleaner (PN: 999MPA3050P) or an equivalent foaming glass cleaner (Figure 3 and Figure 4).

To avoid damage to the headlamp assemblies:


Do not use glass cleaner containing ammonia.



Do not use any other harsh chemicals to clean the headlamp lenses.

Foaming
glass cleaner
Figure 3

6.

Foaming glass cleaner on
headlamp
headlamps
lenses
Figure 4

Stand approximately 3 – 3 1/2 feet
back from the center of the front
bumper to view the headlamp low
beam light pattern on the headlamp
lenses.

3 – 3 1/2 ft

Figure 5

3/8

NTB22-024A

7.

Visually inspect and compare the low beam light pattern projected on both of the
headlamp lenses to the Good (OK) Examples (Figure 6 - Figure 11 on pages 4 and 5)
and the No Good (NG) Examples (Figure 12 - Figure 15 on page 6).


If the headlamp low beam light pattern condition is OK, the inspection process is
complete.
o Write the inspection result of each headlamp assembly on the repair order.



If the headlamp low beam light pattern condition is No Good (NG) for either of the
headlamp assemblies:
a. Write the inspection result of each headlamp assembly on the repair order.
b. Proceed to step 8 on page 7 to replace both headlamp assemblies.

Good (OK) Examples
2016-2018 Models shown, 2013-2015 Models are similar
NOTE: The figures below show the low beam light pattern without Nissan Foaming
Glass Cleaner.
Right Combination Lamp (OK)

Left Combination Lamp (OK)

Dark center circle

Square shape
light pattern
Figure 6

Dark center circle

Square shape
light pattern
Figure 7

4/8

NTB22-024A

Good (OK) Examples
NOTE: The figures below show the low beam light pattern enhanced with Nissan
Foaming Glass Cleaner.
2013-2015 Models
Right Combination Lamp (OK)

Left Combination Lamp (OK)

Dark center circle

Square shape
light pattern

Dark center circle

Square shape
light pattern

Figure 8

Figure 9

2016-2018 Models
Right Combination Lamp (OK)

Left Combination Lamp (OK)

Dark center circle

Square shape
light pattern
Figure 10

Dark center circle

Square shape
light pattern
Figure 11

5/8

NTB22-024A

No Good (NG) Examples
2013-2015 Models shown, 2016-2018 Models are similar
IMPORTANT: Headlamp assemblies with yellowed or hazed lenses do not affect the
low beam light pattern. Replacement of headlamp assemblies for yellowed or hazed
lenses is not covered by this Voluntary Service Campaign.
NOTE: The figures below show the low beam light pattern without Nissan Foaming
Glass Cleaner.
Right Combination Lamp (NG)

Left Combination Lamp (NG)

Square shape
very dim/missing

Only pattern is
bright spot

Center circle distorted

Figure 12

Figure 13

NOTE: The figures below show the low beam light pattern enhanced with Nissan
Foaming Glass Cleaner.
Right Combination Lamp (NG)

Left Combination Lamp (NG)

Square shape
very dim/missing
Only pattern is
bright spot

Center circle distorted

Figure 14

Figure 15

6/8

NTB22-024A

8.

Replace the headlamp assemblies.
IMPORTANT: Do NOT replace headlamp assemblies for yellowed or hazed lenses.

9.



For 2013-2015 Altima, refer to the ESM for the Sedan: DRIVER CONTROLS >
EXTERIOR LIGHTING SYSTEM > REMOVAL AND INSTALLATION > FRONT
COMBINATION LAMP > Removal and Installation - Halogen



For 2016-2018 Altima, refer to the ESM: DRIVER CONTROLS > EXTERIOR
LIGHTING SYSTEM > HALOGEN HEADLAMP > REMOVAL AND
INSTALLATION > FRONT COMBINATION LAMP > Removal and Installation

Perform headlamp aiming adjustment on the replaced headlamp assemblies.


For 2013-2015 Altima, refer to the ESM for the Sedan: DRIVER CONTROLS >
EXTERIOR LIGHTING SYSTEM > PERIODIC MAINTENANCE > HEADLAMP >
Aiming Adjustment



For 2016-2018 Altima, refer to the ESM: DRIVER CONTROLS > EXTERIOR
LIGHTING SYSTEM > HALOGEN HEADLAMP > PERIODIC MAINTENANCE >
HEADLAMP > Aiming Adjustment

7/8

NTB22-024A

PARTS INFORMATION

(1)

DESCRIPTION

PART NUMBER

QUANTITY

LAMP ASSY – HEAD (RH)
(Headlamp Assembly)

26010 – (1)

1
(If Needed)

LAMP ASSY – HEAD (LH)
(Headlamp Assembly)

26060 – (1)

1
(If Needed)

Use the VIN in the Electronic Parts Catalog to determine the correct part number.

CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN
(“CM”) ID

PC861

DESCRIPTION

OP CODE

FRT

INSPECT FRONT COMBINATION LAMP
(BOTH SIDES) OK CONDITION

PC8610

0.2

PC8611

1.4

PC8612

0.2

INSPECT FRONT COMBINATION LAMP
(BOTH SIDES) & RP (BOTH SIDES)
INSPECT FRONT COMBINATION LAMP
(BOTH SIDES) NG CONDITION
PARTS NOT AVAILABLE

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
March 24, 2022

NTB22-024

May 19, 2022

NTB22-024A

DESCRIPTION
Original bulletin published
CLAIMS INFORMATION updated, Sedan added to
title and model references throughout

8/8

NTB22-024A