NUMBER:
GROUP:
DATE:

18-023-16 REV. C
Vehicle Performance
June 21, 2016

This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

THIS BULLETIN SUPERSEDES SERVICE BULLETIN 18-023-16 REV. B DATED JUNE
02, 2016, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE
HIGHLIGHTED WITH **ASTERISKS** AND INCLUDES UPDATED DIAGNOSTIC
TROUBLE CODES (DTCs) FOR 2013 PF VEHICLES AND LABOR OPERATION.
THIS SERVICE BULLETIN IS ALSO BEING RELEASED AS RAPID RESPONSE
TRANSMITTAL (RRT) 15-012. ALL APPLICABLE SOLD AND UN-SOLD RRT VIN's
HAVE BEEN LOADED. TO VERIFY THAT THIS RRT SERVICE ACTION IS
APPLICABLE TO THE VEHICLE, USE VIP OR PERFORM A VIN SEARCH IN
TECHCONNECT. ALL REPAIRS ARE REIMBURSABLE WITHIN THE PROVISIONS OF
WARRANTY.
FOR HELP WITH USING wiTECH FOR ECU FLASH REPROGRAMMING, CLICK ON
THE APPLICATION’S “HELP” TAB.
THE wiTECH SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE
PERFORMING THIS PROCEDURE.
SUBJECT:
Flash: 2.4L Powertrain Diagnostic and System Improvements
OVERVIEW:
This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest
available software.
MODELS:
2013 - 2015

(PF)

Dodge Dart

2015

(UF)

Chrysler 200

NOTE: This bulletin applies to vehicles equipped with a 2.4L Engine (Sales Codes
ED6 or ED8).

18-023-16 REV. C

-2-

SYMPTOM/CONDITION:
A small number of customers may experience a Malfunction Indicator Lamp (MIL)
illumination or one or more of the following conditions. Upon further investigation the
technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM
memory:
2015 UF Vehicles with (Sales Codes ED6, ED8)
•
•
•
•
•
•
•
•
•
•
•
•

P050D - Cold Start Rough Idle.
P0335 - Crankshaft Position Sensor Circuit.
P1607 - PCM Internal Shutdown Timer Rationality.
P0133 - O2 Sensor 1/1 Slow Response.
P0456 - EVAP System Small Leak.
P0480 - Cooling Fan 1 Control Circuit/Open.
U0402 - Implausible Data Received From TCM.
P2172 - High Airflow/Vacuum Leak Detected.
P1D73 - AGS Performance.
U0140 - Lost Communication With Body Control Module.
P0441 - Evap Purge System Performance.
P0116 - Engine Coolant Temperature Sensor 1 Performance.

In addition to the DTCs above the following improvements have been made:
•
•

Engine Startup Flare and Idle Surge.
Improved vehicle acceleration.

2015 PF Vehicles with (Sales Codes ED6, ED8)
•
•
•
•
•
•
•
•
•
•
•
•
•

U0401 - Implausible Data Received From ECM/PCM - Signal Invalid.
P1185 - General Pressure Sensor Correlation.
P050D - Cold Start Rough Idle.
P0133 - O2 Sensor 1/1 Slow Response.
P0456 - Evap System Small Leak.
P219A - Bank 1 Air-Fuel Ratio Imbalance.
P2172 - High Airflow/Vacuum Leak Detected.
P1D73 - AGS Performance.
U0140 - Lost Communication With Body Control Module.
P0116 - Engine Coolant Temperature Sensor 1 Performance.
P050B - Cold Start Ignition Timing Performance.
P061A - Level 2 Torque Performance.
P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation).

In addition to the DTCs above the following improvements have been made:
•
•
•

Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F).
Cold Idle Surge With AC Engaged.
Improve cabin warm up in cold weather, when the vehicle is in park or neutral and
the temperature is between -12°C to 4.5°C (10°F to 40°F).

2013 PF Vehicles with (Sales Code ED6)
•
•
•
•
•
•

**P0335 - Crankshaft Position Sensor Circuit.
P2610 - PCM Internal Engine Off Timer Performance.
P0456 - Evap System Small Leak.
P1185 - General Pressure Sensor Correlation.**
P219A - Bank 1 Air-Fuel Ratio Imbalance.
P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open.

-3•
•
•
•

18-023-16 REV. C

P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
P2172 - High Airflow/Vacuum Leak Detected.
P1D73 - AGS Performance.
U0140 - Lost Communication With Body Control Module.

2014 PF Vehicles with (Sales Codes ED6)
•
•
•
•
•
•
•
•
•
•
•
•

P0335 - Crankshaft Position Sensor Circuit.
P2610 - PCM Internal Engine Off Timer Performance.
P0456 - EVAP System Small Leak.
P1185 - General Pressure Sensor Correlation.
P219A - Bank 1 Air-Fuel Ratio Imbalance.
P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open.
P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range.
P2172 - High Airflow/Vacuum Leak Detected.
P1D73 - AGS Performance.
U0140 - Lost Communication With Body Control Module.
P0116 - Engine Coolant Temperature Sensor 1 Performance.
P0441 - EVAP Purge System Performance.

DIAGNOSIS:
Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in
TechCONNECT, verify all related systems are functioning as designed. If DTCs or
symptom conditions, other than the ones listed above are present, record the issues on the
repair order and repair as necessary before proceeding further with this bulletin.
If a customer’s VIN is listed in VIP or your RRT VIN list, perform the repair. For all other
customers that describe the symptom/condition, or if the technician finds any of the DTCs
listed above perform the Repair Procedure.
REPAIR PROCEDURE:
NOTE: The Transmission Control Module (TCM) must be updated to the latest
available software at the conclusion of this repair procedure. Refer to all
applicable published service bulletins for detailed repair procedures and
labor times regarding updating the TCM software.
NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2
volts. Do not allow the charging voltage to climb above 13.5 volts during the
flash process.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
1. Reprogram the PCM with the latest software. Detailed instructions for flashing control
modules using the wiTECH Diagnostic Application are available by selecting the
application’s “HELP” tab.
NOTE: If the PCM already has the latest software, use inspection LOP 18-19-06-FA to
close the active RRT.
2. Clear any DTCs that may have been set in any module due to reprogramming. The
wiTECH application will automatically present all DTCs after the flash and allows them
to be cleared.

18-023-16 REV. C

-4-

3. Verify the TCM is programmed with the latest available software. Refer to all
applicable published service bulletins for detailed repair procedures and labor times
regarding updating the TCM software.
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation No:

Description

Skill Category

Amount

18-19-06-FA

Module, Powertrain Control 1 - Engine Repair
(PCM) - Inspection Only
and Performance
(0 - Introduction)

0.2 Hrs

**18-19-06-KQ

Module, Powertrain Control 1 - Engine Repair
(PCM) - Inspect and
and Performance
Reprogram
(0 - Introduction)

0.2 Hrs**

NOTE: The expected completion time for the flash download portion of this
procedure is approximately 5 minutes. Actual flash download times may be
affected by vehicle connection and network capabilities.
FAILURE CODE:
The dealer must choose which failure code to use. If the customer came in with an
issue and the dealer found updated software to correct that issue, use failure code
CC, for all other use failure code RF.
•
•

If the customer’s concern matches the SYMPTOM/CONDITION identified in the
Service Bulletin, failure code CC is to be used.
If an available flash is completed while addressing a different customer concern,
failure code RF is to be used.

CC

Customer Concern

RF

Routine Flash