S.A.T.

103 rev2
MV

area

n°

Service Bulletin
Circolare tecnica - Technisches Rundschreiben - Circulaire Technique - Circular Tecnica

Data:

8 February 2013

Subject:

Re-mapping ECU and Key switch Update

Product:

F4 - F4 R - F4 RR - MY 2013

This Service Bulletin rev 2 voids and replaces the previous, introducing an updated mapping
for F4 RR and new VIN, we apologize for the inconvenience.
With the following Service Bulletin, we want to inform you that it is mandatory to update the mapping
and to replace the electrical part of key switch in the F4 MY 2013. These upgrades are the product
of the continuous quality control of our motorcycles.
It is mandatory to install the updates on all the new motorcycles before consignment to the
customer.

Updates are necessary on the following bikes:
•

MODEL F4 - R - RR MY 2013 from VIN ..DV003401 up to VIN ..DV003798 included

TOOLS AND MATERIALS NECESSARY FOR THE UPDATE:
1. Re-mapping ECU:
TEXA Navigator IDC4 with software multibrand and cable 3151/AP34.
2. Key switch update:
- N° 1 part number W000W0996 PARTE ELETTRICA ZADI
This spare part will be sent directly from MV Agusta, the costs will be reimbursed through normal
warranty procedure; the shipping costs will be covered by MV Agusta.
You will not need to order these parts.
•

PROCEDURE TO IMPLIMENT THE UPDATES:

Re-mapping the ECU:
- Update your TEXA Navigator IDC4 instrument by connecting to the internet with the software
IDC4, select “Search for Updates” and begin the download.
- Select “Bike” and then “Diagnosis” and the motorcycle model, F3 675 (until the release of the
TEXA software update, all the diagnostic and remapping operations concerning the F4 1000 MY
2013 model range, must be completed in the F3 675 menu).
- Press “ECU Update” followed by “Injection Reprogramming” and then the ECU ELDOR
- Connect to the motorcycle following the instructions of the program and then select “MAPPPING”
Service Bulletin n° 103 rev 2- Re-mapping and Key switch F4 2013

1/5

•

F4 – F4 R - Install the new map in the ECU selecting the file “0502F027” with the password
“NEMO#16dd1a13”, follow the instructions to complete the installation.

•

F4 RR - Install the new map in the ECU selecting the file “0502FD27” with the password
“NEMO#12h4u413”, follow the instructions to complete the installation.

- After flashing, verify in "ECU INFO" the code of the installed map.
- Exit from current menu “ECU Update” and open menu “Self-diagnosis”.
- Select “Settings” and than “Reset self-adapting parameters” follow the instructions to complete the
operation.
- Start the engine and let idle until cooling fan turns on
Key switch update:
- Remove the windshield

- Remove the 3 fairing fixing screws on both
Right and Left fairings as shown in figure

-Remove the Right and Left covers by
unscrewing the 2 fixing screws and pulling
gently the side fairing in order to facilitate the
extraction. Reconnect the side fairings in
order to avoid any interference with the
handlebar during the operation.

Service Bulletin n° 103 rev 2- Re-mapping and Key switch F4 2013

2/5

- Remove the little cover under the key switch
by loosening the 2 fixing screws

- Disconnect the two clips that are fixing the
key switch’s electrical part

- Remove the Key Switch

Service Bulletin n° 103 rev 2- Re-mapping and Key switch F4 2013

3/5

- Remove the white connector as shown in
figure

- Disconnect the key switch connector

- Now remove the Key Switch, to facilitate the
operation we recommend to identify the key
switch cable on the right side of the steering
column and cut it.

Take the new key switch part number
W000W0996 “PARTE ELETTRICA ZADI”
identified by the label as shown in figure and
proceed with the installation of the component
by inverting the disassembly operations
previously described.
- If necessary turn the key in order to find the
correct timing.

Service Bulletin n° 103 rev 2- Re-mapping and Key switch F4 2013

4/5

- Position the key switch cable between the
airbox and the connectors group.

- Insert the key switch in place and fix the cover with the 2 screws previously removed.
- Reassemble the motorcycle.
- Test the motorcycle before consignment to the customer.
- Please refer to the Service Manual for any information not included in this document.

For any need we advice you to contact the MV Agusta Service Dept. by sending an email to the
following address: [email protected]

Procedure for Warranty reimbursement:
Send a Warranty Request for reimbursement of the parts and labor including all the relevant
information regarding the motorcycle and parts with the following codes:
ƒ Warranty Type = GS
ƒ Special Warranty Code = 2775
ƒ Operation Code: T 999
ƒ Labor: 0,7 hours
ƒ Defect Code: 099
Make note to the Circolare Tecnica N°103
The reimbursement of the warranty request will be carried out via Invoice as is the normal
procedure.
Thank you in advance for your cooperation.
Best Regards,
MV AGUSTA MOTOR S.p.A.
Technical Service Department

Service Bulletin n° 103 rev 2- Re-mapping and Key switch F4 2013

5/5