L-SB-0051-21

December 22, 2021

2022 LX 600 Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2022

LX600

ADDITIONAL INFORMATION

Introduction

This bulletin contains the vehicle specific pre-delivery services for 2022 model year LX 600
vehicles. Additionally, refer to the applicable Pre-Delivery Service (PDS) Check Sheet for
services to be performed.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

Procedures



D/C Cut Fuse (30A) Installation ............................................................................................. 2



Seating Position Control ECU Initialization ............................................................................ 3



Installation of Towing Hitch Cover*........................................................................................ 3



Front License Plate and Mounting Bracket Installation*......................................................... 4



Tire Pressure Warning System Initialization .......................................................................... 6

*If Applicable

Draft - Confidential

© 2021 Lexus, a division of Toyota Motor Sales, USA

Page 1 of 6

L-SB-0051-21

December 22, 2021

Page 2 of 6

2022 LX 600 Pre-Delivery Service (PDS)
D/C Cut Fuse (30A) Installation

To minimize battery discharge during transportation and storage, the D/C cut fuse (30A) has
been removed at the assembly plant and temporarily stored in the blank space of the relay block
in the engine compartment. During PDS, reinstall the D/C cut fuse (30A) to its original location
and confirm ALL related Diagnostic Trouble Codes (DTCs) are cleared.
Remove the D/C cut fuse (30A) from the blank space of the relay block in the engine
compartment and install the D/C cut fuse (30A) in the relay block as shown.
Figure 1.

3

2

1

1

Remove D/C Cut Fuse (30A)

2

Install D/C Cut Fuse (30A) (Original Location)

3

Relay Block

NOTE
With the DC CUT FUSE (30A) removed, the diagnostic trouble code (DTC) is detected when the
ignition is turned on during transportation. Clear all DTCs using the GTS after checking that there are
no malfunctions on the vehicle.

Draft - Confidential

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0051-21

December 22, 2021

Page 3 of 6

2022 LX 600 Pre-Delivery Service (PDS)
Seating Position Control ECU Initialization

Refer to the applicable Repair Manual for the seating position control ECU initialization
procedure (procedure 3).

Installation of Towing Hitch Cover

1. Attach the two provided clips to install the
towing hitch cover.

Figure 2.

1
c

2
c

Draft - Confidential

1

Towing Hitch Cover

2

Clip

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0051-21

December 22, 2021

Page 4 of 6

2022 LX 600 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation

The front license plate mounting bracket and two self-tapping screws for the 2022 model year
LX 600 are stored in the rear cargo area of the vehicle. For states that require a front license
plate, install the license plate and mounting bracket during PDS.

1. Remove the two radiator grille mouldings
by disengaging the three claws on each.

Figure 3.

1

1

Attach the front license plate mounting
bracket hooks to the air intake of the
radiator grille and hold in place.

Radiator Grille Moulding

Figure 4.

1
c

Align holes “A” of the mounting
bracket with the installation holes on
the radiator grille.
NOTE

2
c

 Holes “A” are used to install the mounting
bracket to the bumper cover.
 Holes “B” are used to install the front
license plate to the mounting bracket.

A
c

B
c

A
c

3
c

Draft - Confidential

1

Mounting Bracket

2

Installation Hole

3

Hook

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0051-21

December 22, 2021

Page 5 of 6

2022 LX 600 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)

Install the mounting bracket to the radiator
grille using the two self-tapping
screws provided.

Figure 5.

NOTICE
Do NOT overtighten the
self-tapping screws.
2
c

1
c

4
c

Install the front license plate using two
noncorroding bolts with the
following dimensions:

3
c

2
c

1

Mounting Bracket

2

Self-tapping Screw

3

License Plate

4

Bolt

Figure 6.

Nominal Length: 15.0 mm (0.59 in.)
Diameter: 6.0 mm (0.24 in.)

2

1

Draft - Confidential

1

Nominal Length

2

Diameter

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0051-21

December 22, 2021

Page 6 of 6

2022 LX 600 Pre-Delivery Service (PDS)
Tire Pressure Warning System (TPWS) Initialization

Refer to the applicable Repair Manual for the TPWS initialization procedure. Note the spare tire
does NOT have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using Techstream and select the compensation tire pressure
checkbox. Compensation pressures will display on the Health Check results screen. Adjust the tire
pressure when the tires are cold.

Draft - Confidential

© 2021 Lexus, a division of Toyota Motor Sales, USA