133. Refer to step 139 on page 80 and confirm if a TCM reprogram is available for the
vehicle you are working on.
Is a reprogram available?


YES: Perform TCM reprogramming starting on page 79.



NO: Proceed to step 149 on page 86.

78/106

NTB16-110Q

TCM Reprogramming
G.

IMPORTANT: Before starting, make sure:


ASIST on the CONSULT PC has been synchronized (updated) to the current date.



All CONSULT-III plus (C-III plus) software updates (if any) have been installed.

NOTE:


Most instructions for reprogramming with C-III plus are displayed on the CONSULT
PC screen.



If you are not familiar with the reprogramming procedure, click here. This will link
you to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure.

CAUTION:


Connect a battery maintainer or smart charger set to reflash mode or a similar
setting. If the vehicle battery voltage drops below 12.0V or rises above 15.5V
during reprogramming, the TCM may be damaged.



Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the TCM may be damaged.



Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the TCM may be damaged.



Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.)
within range of the CONSULT PC and the VI. If Bluetooth® signal waves are
within range of the CONSULT PC during reprogramming, reprogramming may
be interrupted and the TCM may be damaged.

79/106

NTB16-110Q

134. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.

135. Start C-III plus.

136. Wait for the plus VI to be recognized.


The serial number will display when the plus VI is recognized.

137. Select Re/programming, Configuration.

Plus VI is
recognized

Figure 155

138. Follow the on-screen instructions and navigate the C-III plus to the screen shown in
Figure 156 on the next page.

139. When you get to the screen shown in Figure 156, confirm reprogramming applies as
follows.
A. Find the TCM Part Number and write it on the repair order.
NOTE: This is the current TCM Part Number (P/N).

80/106

NTB16-110Q

TRANSMISSION

Current TCM P/N

31036 -

Figure 156
H.

B. Compare the P/N you wrote down to the numbers in the Current TCM Part Number
column in Table B below.
 If there is a match, continue with the reprogramming procedure; step 140.
 If there is not a match, reprogramming is not needed; continue to step 149,
Perform ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE.
Table B
MODEL

MODEL
YEAR
2013

Altima
(4-cyl
engine only)

2014-2015
2016
2017
2014

CURRENT TCM PART NUMBER BEFORE
REPROGRAMMING: 31036 3NV0A, 3NV1A
3TA0A, 3TA4A, 3TA4B, 3TA4C, 3TA9C
3TY0A, 3TY0B, 3TY0C, 3TY0D, 3TY0E
3TY1A, 3TY1B, 3TY1C, 3TY1D, 3TY1E
9HM0A, 9HM0C, 9HM0D, 9HM0E
9HM3A, 9HM3B, 9HM3C, 9HM3D
3TE0C, 3TE0D, 3TE2C, 3TE2D
3TH0A, 3TH0B, 3TH0C, 3TH2A, 3TH2B, 3TH2C
3TE0D, 3TE2D, 9HS4A, 9HS6A, 9HS7A, 9HS8A
4BA0A, 4BA0B, 4BA5A, 4BA5B, 4BA8A
4BA9A, 4BA9B, 4BA9C, 4BA9D, 4BA9E

2015

5HA0A, 5HA0B, 5HA0C, 5HA5A, 5HA9A, 5HA9B
9TA0A, 9TA0B, 9TA0C, 9TA0D
9TA5A, 9TA9A, 9TA9B

2016

5HJ0A, 5HJ0B, 5HJ0C, 5HJ0D, 5HJ8A, 5HJ9A, 5HJ9B
6FJ0A, 6FJ0B, 6FJ0C, 6FJ0D
6FJ8A, 6FJ9A, 6FJ9B, 6FK0A, 6FK9A

2017

5HK0A, 5HK0B, 5HK1A, 5HK1B, 5HK8A, 5HK9A
6FL0A, 6FL0B, 6FL1A, 6FL1B, 6FL8A, 6FL9A

Rogue

140. Follow the on-screen instructions to navigate C-III plus and reprogram the TCM.
81/106

NTB16-110Q

NOTE:


In some cases, more than one new P/N for reprogramming is available.
 If more than one new P/N is available, the screen in Figure 157 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.



If you get this screen and it is blank (no reprogramming listed), it means there is
no reprogramming available for this vehicle. Close C-III plus and refer back to
ASIST for further diagnosis.

TRANSMISSION

Figure 157


Before reprogramming will start, you will be required to enter your User Name and
Password.
 The CONSULT PC must be connected to the Internet (Wi-Fi or cable).
 If you do not know your User Name and Password, contact your service
manager.

Figure 158

82/106

NTB16-110Q

141. When the screen in Figure 159 displays, reprogramming is complete.

NOTE: If the screen in Figure 159 does not display (indicating that reprogramming did
not complete), refer to the information on the next page.

142. Disconnect the battery maintainer/smart charger from the vehicle.

143. Select Next.

Figure 159

NOTE:


In the next step (page 85) you will perform Erase All DTCs.



DTC erase is required before C-III plus will provide the final reprogramming
confirmation report.

83/106

NTB16-110Q

TCM Recovery:
Do not disconnect plus VI or shut down C-III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 160:


Check battery voltage
(12.0–15.5 V).



Ignition is ON, engine OFF.



External Bluetooth® devices
are OFF.



All electrical loads are OFF.



Select retry and follow the
on screen instructions.



“Retry” may not go through on
first attempt and can be
selected more than once.

Figure 160

If reprogramming does not complete and the “X” icon displays as shown in
Figure 161:


Check battery voltage
(12.0 – 15.5 V).



CONSULT A/C adapter is
plugged in.



Ignition is ON, engine OFF.



Transmission is in Park.



All C-III plus / VI cables are
securely connected.



All C-III plus updates are
installed.
Figure 161



Select Home, and restart
the reprogram procedure
from the beginning.

84/106

NTB16-110Q

144. Follow the on-screen instructions to Erase All DTCs.

145. When the entire reprogramming process is complete, the screen in Figure 162 will
display.

146. Verify the before and after part numbers are different.

147. Print a copy of this screen (Figure 162) and attach it to the repair order for warranty
documentation.

148. Select Confirm.

31036 - _ _ _ _ _
31036 - _ _ _ _ _

TRANSMISSION

Figure 162

85/106

NTB16-110Q

149. Perform ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE.


Refer to Transaxle & Transmission / RE0F10E / BASIC INSPECTION, and
perform ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE.
NOTE: Use the procedure starting on page 87 for FWD CLUTCH POINT
LEARNING.

IMPORTANT: Check off these additional services as they are completed and attach
this to the repair order when finished.
CHECK OFF

ADDITIONAL SERVICE PROCEDURE
PRINT CURRENT CALIBRATION DATA
CHECK THE SERIAL NUMBER
WRITE THE DATA (WRITE IP CHARA)
PRINT NEW CALIBRATION DATA
FWD CLUTCH POINT LEARNING
(If needed, TCM reprogramming must be done first.
Use procedure starting on page 87.)
PERFORM SELECT LEARNING
(DRIVE/REVERSE LEARNING on page 90)
ERASE CVT FLUID DEGRADATION LEVEL DATA

150. Return C-III plus to the Home screen.

151. Turn OFF C-III plus and the vehicle ignition.

152. Disconnect C-III plus from the vehicle.

153. Test drive the vehicle:


Make sure the MIL is OFF.



This bulletin does not cover any DTC repairs other than those listed on page 2 in
the Flow Chart.



If the MIL comes ON, go to ASIST for further diagnostic information.



Verify the CVT operates normally and no abnormal noises are heard during a test
drive.

86/106

NTB16-110Q

FWD CLUTCH POINT LEARNING (using CONSULT-III plus)
NOTE: If a TCM update is available (see page 80), the TCM MUST be reprogrammed
before performing FWD CLUTCH POINT LEARNING.

154. Apply the vehicle’s parking brake.
155. Start the engine and warm up to
operating temperature (50-100o C
[122-212o F]).
156. Connect the CONSULT PC to the
vehicle.
157. Start C-III plus.
158. Wait for the plus VI to be recognized.


The serial number will display
when the plus VI is recognized.
Figure 163

159. Select Diagnosis (One System).

160. Select Work Support under
TRANSMISSION.

Figure 164

IMPORTANT: The following FWD CLUTCH
POINT LEARNING will be performed twice;
once in drive (D) and once in reverse (R).

161. Select FWD CLUTCH POINT
LEARNING and then Start.

Figure 165
87/106

NTB16-110Q

162. With the engine still running and at
idle, depress the brake pedal and shift
the CVT into neutral (N).


Confirm that all of the required
conditions indicated in Figure 166
are being met.

Required
conditions

163. Select Start.
Figure 166

164. While maintaining all conditions shown
in Figure 166 and the “Current status”
indicates “EXECUTING”, shift the CVT
into D and then wait until the Current
status indicates “COMPLETED”.
NOTE: This may take up to three (3)
minutes to complete.

Figure 167

165. When the screen in Figure 168 is
displayed, shift the CVT into P, and
then select End.

Figure 168

166. Turn the engine OFF and then back
ON.

88/106

NTB16-110Q

167. Select FWD CLUTCH POINT
LEARNING and then Start.

Figure 169

168. With the engine still running and at
idle, depress the brake pedal and shift
the CVT into neutral (N).


Confirm that all of the conditions
indicated in Figure 170 are being
met.
Required
conditions

169. Select Start.

Figure 170

170. While maintaining all conditions shown
in Figure 170 and the Current status
indicates EXECUTING, shift the CVT
into R and then wait until the Current
status indicates COMPLETED.
NOTE: This may take up to 3 minutes
to complete.
Figure 171

89/106

NTB16-110Q

171. When the screen in Figure 172 is
displayed select End, shift the CVT
into P, and then turn the engine OFF.

Figure 172

SELECT LEARNING (DRIVE/REVERSE LEARNING)

Perform Select Learning (Drive / Reverse Learning) as follows:

172. Set the parking brake.

173. Start the engine, and then wait five (5) seconds.

174. Move the shift selector to the N position and hold for more than two (2) seconds, and
then move it to the D position and wait for transmission engagement.

175. Repeat step 174 ten times.

176. Move the shift selector to the N position and hold for more than 2 seconds, and then
move it to the R position and wait for the transmission engagement.

177. Repeat step 176 ten times.

178. Move the shift selector to the P position, and continue to step 179 on page 91.

90/106

NTB16-110Q

Erase CVT Fluid Degradation Level Data
179. Select Work Support in TRANSMISSION.
180. Select CONFORM CVTF DETERIORTN.
181. Select Clear.
182. Clear any DTCs that may have set and then test drive the vehicle.

91/106

NTB16-110Q

TROUBLESHOOTING
The Dummy Cover Will Not Sit Flush
If the dummy cover does not sit flush, the
clutch pack may not be fully seated.


Figure 173 shows the clutch pack
fully seated.



The clutch pack is not fully seated if it
is not below the surface that the
dummy cover bolts to.



Use the instructions below to fully
seat clutch pack.