L-SB-0031-21

September 10, 2021

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2022

IS300, IS350, IS500

ADDITIONAL INFORMATION

Introduction

This bulletin contains the vehicle specific pre-delivery services for 2022 model year IS 300,
IS 350, and IS 500 vehicles. Additionally, refer to the applicable Pre-Delivery Service (PDS)
Check Sheet for services to be performed.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

Procedures



D/C Cut Fuse Installation ...................................................................................................... 2



Deletion of Vehicle Alert History ............................................................................................ 3



Parking Assist Monitor Initialization*...................................................................................... 4



Steering Sensor Zero Point Calibration* ................................................................................ 4



Front Emergency Towing Eyelet Removal and Hole Cover Installation ................................. 5



Front Wheel Opening Extension Pad Installation .................................................................. 6



Front License Plate and Mounting Bracket Installation*......................................................... 7



Installation of Rubber Body Plugs ......................................................................................... 9



Tire Pressure Warning System (TPWS) Initialization........................................................... 10

*If applicable.

© 2021 Lexus, a division of Toyota Motor Sales, USA

Page 1 of 10

L-SB-0031-21

September 10, 2021

Page 2 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
D/C Cut Fuse Installation

To minimize battery discharge during transportation and storage, the D/C cut fuse (30A) has
been removed at the assembly plant and temporarily stored in the blank space of the relay block
in the engine compartment. During PDS, reinstall the D/C cut fuse (30A) into its original location
and clear ALL related Diagnostic Trouble Codes (DTCs).
Figure 1.

1
c

3
c

2

1

Relay Block

3

2

Remove D/C Cut Fuse (30A)

Install D/C Cut Fuse (30A) (Original Location)

NOTE
While the vehicle is stored at the dealership, disconnect the negative (–) battery terminal to prevent
battery discharge. Refer to L-SB-0013-21, Battery Maintenance During PDS, for battery
maintenance information.

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0031-21

September 10, 2021

Page 3 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Deletion of Vehicle Alert History

As the D/C cut fuse is removed, the communication between the various ECUs is interrupted.
When the D/C cut fuse is reinstalled, the communication status is restored, but Lexus Enform
Service Connect may store malfunction history in the form of vehicle alert history.
Therefore, it is necessary to operate the multi-display and delete the vehicle alert history AFTER
installing the D/C cut fuse during PDS at the dealership.
Deletion Procedure

1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Push the Menu switch on the remote touch device.
3. On the multi-display, enter the following menus: Info – Vehicle Alert History.
4. If there is vehicle alert history stored, perform the Delete History operation.
HINT
If there is no vehicle alert history stored, the system will display a message stating
“There is no vehicle alert history.”

5. When the vehicle alert history deletion confirmation screen is displayed, select Yes.
HINT
If there is no vehicle alert history stored, the system will display a message stating
“There is no vehicle alert history.”

6. Turn the engine switch (power switch) to the OFF position (OFF mode).

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0031-21

September 10, 2021

Page 4 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Parking Assist Monitor Initialization

As a result of the removal of the D/C cut fuse, the power source to the steering angle sensor is
cut off. When the D/C cut fuse is reinstalled, the parking assist monitor system/panoramic view
monitor will be operative, but it cannot display guidelines to assist parking operation because the
center position recognized by the steering angle sensor may not be in an initial position.
Therefore, perform parking assist monitor initialization AFTER installing the D/C cut fuse
during PDS.
Refer to the applicable Repair Manual for the parking assist monitor initialization procedure.

Steering Sensor Zero Point Calibration

As a result of the removal of the D/C cut fuse, the steering angle sensor power source is cut off.
When the D/C cut fuse is reinstalled, the center position recognized by the steering angle sensor
may not be the appropriate position. Therefore, it is necessary to perform the steering sensor
zero point calibration AFTER installing the D/C cut fuse during PDS.
Refer to the applicable Repair Manual for the steering sensor zero point calibration procedure.

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0031-21

September 10, 2021

Page 5 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Front Emergency Towing Eyelet Removal and Hole Cover Installation

1. Remove the front and/or rear emergency towing eyelet(s) from the radiator grille or rear
bumper by turning them counterclockwise.
NOTE
If it is difficult to loosen the emergency towing eyelet(s), use a steel bar.
Figure 2.

1
2
c

1

Front Emergency Towing Eyelet

2

Rear Emergency Towing Eyelet

2. Place one of the removed emergency
towing eyelets into the tool tray in the
luggage compartment.

Figure 3.

1
c

1

Front Emergency Towing Eyelet

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0031-21

September 10, 2021

Page 6 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Front Emergency Towing Eyelet Removal and Hole Cover Installation (continued)

3. Install the emergency towing eyelet hole
cover(s), which is(are) stored in the glove
compartment, onto the radiator grille or
rear bumper.

Figure 4.

B

A

B

A. Insert the arrow-shaped tab of the
emergency towing eyelet hole cover “A”
into the eyelet hole tab “B” as shown.

1
c
2
c

B. Install the emergency towing eyelet
hole cover to the hole in the radiator
grille or rear bumper.

A

A

Arrow-shaped Tab

B

Eyelet Hole Tab

1

Front Emergency Towing Eyelet Hole Cover

2

Rear Emergency Towing Eyelet Hole Cover

Front Wheel Opening Extension Pad Installation

The front wheel opening extension pad set (right and left front wheel opening extension pads
and tapping screws) is located in the luggage compartment at the assembly plant to avoid
damage in transit.
1. Place the left front wheel opening
extension pad on the installation position
and temporarily tighten the tapping screws.
Then, tighten the tapping screws.

Figure 5.
B

A

NOTE
There is a distinguishable mark on
each opening extension pad.

2. Repeat step 1 for the right side.

1
c

A

IS 300, IS 350

B

IS 500

1

Tapping Screw

© 2021 Lexus, a division of Toyota Motor Sales, USA

1
c

L-SB-0031-21

September 10, 2021

Page 7 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation

The front license plate bracket and two self-tapping screws are stored in the vehicle at the assembly
plant. Follow this procedure to install the front license plate bracket and front license plate in states
where it is required by law.
1. Align holes “A” of the mounting bracket with
the dimples on the radiator grille. Mark the
location of holes “B” on the radiator grille.

Figure 6.
B

B

NOTE
 Holes “A” are used for installation of the
mounting bracket to the radiator grille.
 Holes “B” are used for the installation of the
front license plate to the mounting bracket.

A

3
c

2. Drill two relief holes with a diameter of
10 mm (0.39 in.) at the hole B marks on the
radiator grille to prevent the license plate
retaining bolt end from contacting the
radiator grille.
NOTICE
 Do NOT pre-drill holes into the
radiator grille.
 Do NOT drill dimples on the radiator grille.

1
c

1

Mounting Bracket

2

Dimple

3

Mark and Drill Hole

© 2021 Lexus, a division of Toyota Motor Sales, USA

2
c

L-SB-0031-21

September 10, 2021

Page 8 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)

3. Install the mounting bracket to the radiator
grille by attaching the two self-tapping screws
into the dimples.

Figure 7.

NOTICE

1
c

Do NOT overtighten the self-tapping screws.

3
c

4. Install the front license plate to the mounting
bracket using two noncorroding bolts with the
following dimensions:

2
c

1

Self-tapping Screw

2

License Plate

3

Bolt

Figure 8.

Nominal Length: 15.0 mm (0.59 in.)
Diameter: 6.0 mm (0.24 in.)

2
c
1
c

1

Nominal Length

2

Diameter

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0031-21

September 10, 2021

Page 9 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Installation of Rubber Body Plugs

1. Confirm the number of plugs in the glove box. If two plugs are present, perform
substep 2A ONLY. If four plugs are present, perform substep 2A AND substep 2B.
2. Install plugs according the instructions below by confirming the number of plugs in the
glove box.
A. Install two plugs in the rear side member hole or rocker inner hole as shown.
B. Install two plugs in the torque box hole or rocker inner hole as shown.
Figure 9.

1

2

z
6

3

z

z

5

z

6

1

Front Side

2

Rear Side

3

Torque Box Hole or Rocker Inner Hole

4

Rear Side Member Hole or Rocker Inner Hole

5

Rocker Inner

6

Install Plug Here (if Applicable)

z

4

z

z

NOTICE
 The installation of these plugs is required to prevent rust.
 These plugs are stored in the glove box.
 The number of plugs may vary according to production locations in the same
vehicle model.

© 2021 Lexus, a division of Toyota Motor Sales, USA

L-SB-0031-21

September 10, 2021

Page 10 of 10

2022 IS 300, IS 350, IS 500 Pre-Delivery Service (PDS)
Tire Pressure Warning System (TPWS) Initialization

Refer to the applicable Repair Manual for the TPWS initialization procedure.
Note the spare tire does NOT have a TPWS sensor.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using Techstream and select the compensation tire pressure
checkbox. Compensation pressures will display on the Health Check results screen. Adjust the tire
pressure when the tires are cold.

© 2021 Lexus, a division of Toyota Motor Sales, USA