KC-2116 Service Bulletin/Repair Instructions

9/27/21, 1:57 PM
Article

NOx Sensor Replacement Guide - US10+OBD13 And Newer

Emissions



Review the tables below to determine which category the DTC currently being diagnosed falls under. Proc

instructions for the appropriate section.
I. Diagnostic Trouble Codes With NOx Sensor in the Description

Fault Code
Fault Description
Comments
P220A-1C
NOx Sensor Supply Voltage Circuit (Bank 1 Sensor 1), Circuit voltage out of range
Power supply - not s
P220B-1C
NOx Sensor Gas Outlet High Voltage, Circuit voltage out of range
Power supply - not s
P225D-00
NOx Sensor Performance - Signal Stuck Low Bank 1 Sensor 1
Sensor reading fresh

issue)
P225F-00
NOx Sensor Performance - Signal Stuck Low Bank 1 Sensor 2
Sensor reading fresh

issue)
U029D-00
Lost Communication With NOx Sensor "A"
Most likely Harness
U029E-00
Lost Communication with NOx Sensor B
Most likely Harness
P229F-64
NOx Sensor Gas Outlet Removed, Signal plausibility failure
Nuisance code, mos
Although the codes above have the term "NOx sensor" in their descriptions, it is highly unlikely that the senso

these codes. The table above specifies the likely cause of each code.

Direction/Repair: DO NOT REPLACE the NOx sensor(s) for these codes. Diagnostics should be performed in a

above.
II. Inlet NOx Sensor (NOx1) Diagnostic Trouble Codes - Sensor Failure Likely
;
Fault Code
Fault Description
P22FB-92
NOx Sensor Performance - Sensing Element Bank 1 Sensor 1, Performance or Incorrect Operatio
P220E-93
NOx Sensor Heater Control Circuit Range/Performance (Bank 1 Sensor 1), No operation
P2200-13
NOx Sensor Bank 1 Sensor 1, Circuit Open
P2203-00
NOx Sensor Circuit High Bank 1 Sensor 1
Live UI
P2205-13
NOx Sensor Gas Outlet Open Circuit, Circuit open
https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/app/VolvoKM_/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD4?pyActivity=%40basec…
1/5
9/27/21, 1:57 PM
Article
P2206-00
NOx sensor heater control circuit low, bank 1 sensor 1
P2208-00
NOx sensor heater sense circuit, bank 1 sensor 1
These codes indicate that the inlet NOx sensor is likely damaged and needs to be replaced.

Direction: In Premium Tech Tool, verify that either the code is Active, or if Inactive that the Confirmed DT

detailed status information as shown in the example below.
Repair: If the DTC meets either of the above criteria, replace the Inlet NOx Sensor ONLY. No other diagno
III. Inlet NOx Sensor (NOx1) Diagnostic Trouble Codes - Potential Sensor Failu

Fault Code
Fault Description
P026C-00
Fuel Injection Quantity Lower Than Expected
P026D-00
Fuel Injection Quantity Higher Than Expected
P2201-64
NOx Sensor Bank 1 Sensor 1, Signal plausibility failure
P225C-00

UI

; Live
NOx Sensor Performance - Signal Stuck High Bank 1 Sensor 1
https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/app/VolvoKM_/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD4?pyActivity=%40basec…
2/5
9/27/21, 1:57 PM
Article
These codes indicate that the inlet NOx sensor is potentially damaged, but further investigation is required to

Direction:

• For US17+OBD2016, US17+OBD2017, and US17+OBD2018 emissions vehicles: PTT test 2589-08-03-18 Exhau

Test, NOx Sensor Test should be performed.

• For all other emissions levels: PTT test 2549-08-03-03 NOx Conversion Test should be performed.

Repair:

• If the NOx1 sensor fails the evaluation, replace the Inlet NOx Sensor ONLY.

• If the NOx2 sensor (Outlet NOx Sensor) fails the test, disregard the results.
IV. Outlet NOx Sensor (NOx2) Diagnostic Trouble Codes - Sensor Failure Likel

Fault Code
Fault Description
P220F-93
NOx Sensor Incorrect Value at Startup, No operation
P229E-13
NOx Sensor Bank 1 Sensor 2, Circuit open
P22A6-00
NOx sensor heater sense circuit, bank 1 sensor 2
P22A1-00
NOx Sensor Circuit High Bank 1 Sensor 2
P22A3-13
NOx Sensor Heater Control Bank 1 Sensor 2, Circuit open
P22A4-00
NOx sensor heater control circuit low, bank 1 sensor 2
P22FE-00
NOx Sensor Performance - Sensing Element Bank 1 Sensor 2
These codes indicate that the outlet NOx sensor is likely damaged and needs to be replaced.

Direction: In Premium Tech Tool, verify that either the code is Active, or if Inactive that the Confirmed DT

detailed status information as shown in the example below.
; Live UI

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/app/VolvoKM_/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD4?pyActivity=%40basec…
3/5
9/27/21, 1:57 PM
Article
Repair: If the DTC meets either of the above criteria, replace the Outlet NOx Sensor ONLY. No other diag

required.
V. Diagnostic Trouble Codes For Emissions System - Either Sensor Possible

Fault Code
Fault Description
P225E-00
NOx Sensor Performance - Signal Stuck High Bank 1 Sensor 2
P20EE-00
SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
P103C-00
NOx Catalyst Efficiency Inducement, Selective Catalytic Reduction (SCR) Unit
P207F-00
Reductant Quality
These codes indicate an issue with the emissions system, which could be caused by a failed NOx sensor.

Direction:

• For US17+OBD2016, US17+OBD2017, and US17+OBD2018 emissions vehicles: PTT test 2589-08-03-18 Exhau

Test, NOx Sensor Test should be performed.

• For all other emissions levels: PTT test 2549-08-03-03 NOx Conversion Test should be performed.

UI

; Live

Repair: Follow guidance from test results.

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/app/VolvoKM_/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD4?pyActivity=%40basec…
4/5
9/27/21, 1:57 PM
Article

Tags
p2200-13
p2203-00
p2205-13
p2206-00
p2208-00
p026c-00
p026d-00
p2201-64
p225c-00
p220f-93
p229e-13
p220a-1c
p220b-1c
p225d-00
p225f-00
u029d-00
u029e-00
p229f-64
p22fb-92
p220e-93
p22a6-00
p22a1-00
p22a3-13
p22a4-00
p22fe-00
p225e-00
p20ee-00
p103c-00
p207f-00
Related links and attachments

No links or attachments available
Feedback

Give feedback to help improve the cont
; Live UI

https://volvo-trkna-prod1.pegacloud.net/prweb/PRAuth/app/VolvoKM_/iNPUIKpeinqPJi2G0hH930k43USdE1gb*/!TABTHREAD4?pyActivity=%40basec…
5/5

SaleBestseller No. 1

OTOFIX D1 Lite 2026 Bidirectional Scan Tool, Bluetooth OBD2 Scanner Diagnostic Tool, 2 Years Free Update, 38+ Services, CANFD & DoIP Protocols, All System Diagnoses, ABS Bleeding, Auto VIN

🎉[OTOFIX D1 Lite, Perfect Cost-effective Diagnostic Tool]: OTOFIX D1 Lite, a newest bidirectional scan tool from OTOFIX company, is a great choice for DIYers and repair shops. 👉This obd2 scanner diagnostic tool packs all practical functions: OE level all systems diagnoses, Bi-Directional Control, 38+ reset services fixing 99% of common problems, support DoIP & CANDF protocols and FCA AutoAuth, high-end hardware configuration. Worldwide vehicles and 🔥2 Years Free Updating🔥 covered.
🎉[Bi-Directional Scan Tool, Active Test]: OTOFIX D1 Lite bluetooth obd2 scanner can also command ECUs and monitor the operation of the actuators to track down the problems of certain parts, like windows, sunroof, wipers, fuel pumps, etc., saving repair time & trouble. This makes OTOFIX D1 Lite the most cost-effective bidirectional scan tool.
🎉[2026 Newest, 38+ Hot Reset Functions]: Equipped with 38+ reset functions in one, the OTOFIX D1 lite automotive scanner diagnostic tool allows you to troubleshoot 99% of common vehicle problems. You can use this car diagnostic scanner holding enough functions to easily repair common vehicle models in your repair shops. Including Oil Reset, Injector Coding, Throttle, DPF Reset, SCR Reset, Gear Learning, Clutch Learning, Suspension, etc. Note* Reset functions vary by model.
🎉[OE Level Full Systems Diagnostics]: Unlike the 2-system and 4-system diagnostic tools, the OTOFIX auto scan tool can complete comprehensive system diagnostics within 5 minutes. It accesses and scans all available onboard systems like for Engine /AT /ABS /EPB /BMS /TPMS /SRS /SAS /Audio System /BCM /Air Conditioning / etc., to read & clear codes, view live data, and check ECU information. Note: Active test is not involved.
🎉[Powerful Hardware Configuration]: Designed with a fashion appearance & a 7” touchscreen and a weight of 463g, this OTOFIX D1 Lite OBD2 diagnostic scanner scan tool is convenient for everywhere and easy to use & store. Android9.0 OS and 2+64GB memory enhance multi-task smoothness and diagnostic operation, no more wasting too much time. 5800mAh battery allows hours-lasting use. WiFi & VCI1 also bring faster communication for your diagnostics.

SaleBestseller No. 2

OTOFIX D1 Lite Bidirectional Scan Tool with 2-Year Free Updates, 2026 New All System Automotive Diagnostic Scanner, 38+ Reset Services, FCA AutoAuth, Active Test, CANFD&DOIP, Auto VIN

🏆【2026 TOP OBD2 Scanner Diagnostic Tool】OTOFIX D1 Lite wireless obd2 scanner has upgraded hardware configuration and car coverage. The newly upgraded D1 Lite with 🔥OS Android 9.0🔥1.5Ghz 4 core high efficiency processor🔥2GB RAM+64GB ROM large storage🔥5800mAh large battery, more stable and longer lasting diagnostics🔥 38+ Reset🔥action tests🔥full system diagnostic🔥Supports MV105 endoscope🔥21+ Language Supports🔥100000+ vehicle coverage to meet all your daily maintenance needs.
👍【Bi-Directional Control / Active Test】D1 Lite obd2 scanner has bidirectional control(worth $300+), which is the most beloved feature among mechanic. If your headlights or car windows are broken, going to a repair shop will cost a lot of money. You can use D1 Lite to send execution commands to the ECU module and identify the repair status. Such as ABS, car windows, doors, valves, wipers, headlights, etc., effectively shorten diagnostic time and reduce diagnostic costs.
🔥【All Systems Diagnostics, In-depth Checking】This advanced OBD2 Scanner D1 Lite can perform OE-level diagnosis of all systems including engine, transmission, airbag, ABS, ESP, TPMS, gateway, steering, radio, and air conditioning for more than 100 brands. This diagnostic scanner supports essential functions, such as reading ECU version info, reading and clearing fault codes, and reading data streams.With just a simple click, it provides you with accurate and in-depth diagnostics.
🏆【38+ Reset Hot Functions】For repair workshops, holding an OTOFIX D1 Lite Auto scanner is a strong advantage over others. Its 38+ maintenance functions provide various solutions for all module repairs, including Oil Reset, TPMS Reset, Injector Coding, Suspension, Throttle Matching, etc., which will usher your repair business to a new pinnacle. Continuously updating will never make the functionality & compatibility out-of-date.
🏆【150+ Models, 10000+ Car Coverage & 16 Languages】D1 Lite is a comprehensive car diagnostic scan tool, help you to troubleshoot car issues fast for 95% US, European, Asian auto makes. ✅ With frequent updates and optimizations allow D1 Lite to cover more vehicles to meet your needs. ✅ Multilingual menu allows auto mechanics around the world to use it without language barriers. 🚩Note: Kindly send us the S/N of the device to authorize new language updates before changing the menu language.

SaleBestseller No. 3

OTOFIX D1 Lite 2026 Bidirectional Scan Tool, 2 Years Free Update, 38+ Services, All System Diagnostic Scanner, Active Tests, AutoAuth FCA SGW, AutoVIN, CAN FD & DoIP, 99% Car Coverage

【2026 OTOFIX D1 Lite Gives the Best Value for Money】OTOFIX D1 Lite bidirectional scan tool is more FASTER and SMARTER with 2026 Enhanced Hardwares & New Functions! 👍Alternative Bluetooth +USB connect 👍2G+64GB 👍4x ARM Cortex-A35 (1.5GHz) Processor (5X Faster CPU) 👍Android 9.0 OS 👍5G GHz WiFi 👍CANFD&DOIP 👍 FCA AutoAuth 👍38+ Services 👍3K+ Bi-Directional Control 👍Full Systems Diagnose 👍2 Years Update 👍150+ Vehicle Coverage.
👍【Active Tests】 OTOFIX D1 Lite is a bi-directional scan tool that can send commands to, and also receive information from vehicle control modules. This way, you can quickly locate and repair faulty auto parts. For Example: send direct commands to ask the vehicle to turn on/off the radiator fan, lights, sound horn, fuel pump, modulate throttle, open/close windows, operate mirrors and more. *Note that only available tests will be displayed in the menu.
👍【38+ Service Functions】 OTOFIX D1 Lite scan tool offers 38+ of the hottest service functions that are commonly used for car repairs. That include Oil reset/SAS/EPB/BMS/Throttle/ABS bleeding, and 2065-new SUS/ADBLUE/NOX/Headlamp resets (and more) to help restore your car status after repairs are done. Compared to other diagnostic scanners for cars, the OTOFIX D1 Lite scanner is much more fully-featured. *Note that specific functions available depend on the make/model/year of your car.
👍【All System Diagnostics + Cloud Report Management】 This 2026 car scanner OTOFIX D1 Lite provides troubleshooting and data for all ECUs: read/clear DTCs, view graphic live data/VIN, and locate system faults for safe driving. With Cloud Report Management, you can save detailed reports to cloud servers and easily shared them with others via QR codes/emails/text messages. Others can access these reports from any device (smartphones/tablets/PCs …) anytime, and you can better manage repair work.
👍【99% Car Coverage】 This one-station car scanner diagnostic for all cars works on 150+ major car brands across the world. 1) It supports CAN-FD/DoIP protocols: compatible with GMCAVALIER/TRAX/Encore/Envision/GL8(LSY)/CT4/CT5 after 2019; Volvo after 2018; Land Rover/Jaguar after 2017; and BM.W F/G all chassis. 2) For models equipped with security modules (such as Renault & 2018+ FCA SGW), its built-in AutoAuth allows you to easily break diagnostic barriers after registration.

This product presentation was made with AAWP plugin.

Last update on 2026-05-13 / Affiliate links / Images from Amazon Product Advertising API

Buffer Email Facebook Flipboard Hacker News LinkedIn Messenger Mix Pinterest Print Reddit SMS Telegram Tumblr X VK WhatsApp Line Xing Threads Bluesky Copy Mastodon Nextdoor