Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

Subject: Cascadia/49X ABS MBSP+ Controller
Software Update
Models Affected: Specific Model Year 2019-2022 Freightliner
Cascadia, and Western Star 49X vehicles, manufactured
September 12, 2018, through March 10, 2021.

General Information
Daimler Trucks North America LLC (DTNA), on behalf of its Freightliner Trucks Division, and wholly owned
subsidiary Western Star Truck Sales, Inc., is initiating Field Service Campaign SF622A to modify the vehicles
mentioned above.
Certain vehicles have a Wabco Anti-Lock Braking System (ABS) controller that logs excessive 629-11 fault
codes which subsequently lead to additional downstream fault codes.
The ABS controller will receive a software update to eliminate erroneous fault codes and ensure its proper
function. After the software update, the truck will require a recalibration drive for the steering angle sensor.
There are approximately 95,677 vehicles involved.
Additional Repairs
Dealers must complete all outstanding Recall and Field Service campaigns prior to the sale or delivery of a
vehicle. A Dealer will be liable for any progressive damage that results from its failure to complete campaigns
before sale or delivery of a vehicle.
Owners may be liable for any progressive damage that results from failure to complete campaigns within a
reasonable time after receiving notification.
Please contact Warranty Campaigns for consideration of additional charges prior to performing the repair.

Work Instructions
Please refer to the attached work instructions. Prior to performing the campaign, check the vehicle for a
completion sticker (Form WAR261).

Replacement Parts
This is a software update; no replacement parts required.

Removed Parts
U.S. and Canadian Dealers, please follow Warranty Failed Parts Tracking shipping instructions for the
disposition of all removed parts. Export distributors, please destroy removed parts unless otherwise advised.

Labor Allowance
Table 1 - Labor Allowance
Campaign
Number

Procedure

SF622A

Update ABS ECU Software

Time Allowed
(hours)

SRT Code

Corrective Action

0.6

996-F095A

12-Repair Recall/Campaign

Table 1

Page 1

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

IMPORTANT: When the campaign has been completed, locate the base completion label in the appropriate location on the vehicle, and attach the gray completion sticker provided in the field service kit (Form WAR261). If
the vehicle does not have a base completion label, clean a spot on the appropriate location of the vehicle and
first attach the base completion label (Form WAR259). If a field service kit is not required or there is no completion sticker in the kit, write the campaign number on a blank sticker and attach it to the base completion label.

Claims for Credit
You will be reimbursed for your labor by submitting your claim through the Warranty system within 30 days of
completing this campaign. Please reference the following information in OWL:
• Claim type is Field Service Campaign.
• In the Campaign field, enter the campaign number and appropriate condition code (SF622-A).
• In the Primary Failed Part field, enter 25-SF622-000.
• In the Labor section, enter the appropriate SRT from the Labor Allowance Table. Administrative time will
be included automatically as SRT 939-6010A for 0.3 hours.
• The VMRS Component Code is F99-999-005 and the Cause Code is A1 - Campaign.
• This Field Service Campaign will terminate on June 30, 2022. Dealers will be notified of any changes to
the termination date via Important Campaign Information Letter posted on DTNAConnect.com.
IMPORTANT: OWL must be viewed prior to beginning work to ensure the vehicle is involved and the campaign
has not previously been completed. Also, check for a completion sticker before beginning work.
All claims must be submitted within 30 days of the repair and within 30 days of the termination date of the
campaign.
For questions, U.S. and Canadian dealers, contact the Warranty Campaigns Department via Web inquiry at
DTNAConnect.com/WSC, or the Customer Assistance Center at (800) 385-4357, if you have any questions or
need additional information. Export distributors submit a Web inquiry or contact your International Service
Manager.

Page 2

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

Copy of Notice to Owners
Subject: Cascadia/49X ABS MBSP+ Controller
Software Update
Daimler Trucks North America LLC (DTNA), on behalf of its Freightliner Trucks division, and wholly owned
subsidiary Western Star Truck Sales, Inc., is initiating Field Service Campaign SF622A to modify specific Model
Year 2019-2022 Freightliner Cascadia, and Western Star 49X vehicles, manufactured September 12, 2018,
through March 10, 2021.
Certain vehicles have a Wabco Anti-Lock Braking System (ABS) controller that logs excessive 629-11 fault
codes which subsequently lead to additional downstream fault codes.
The ABS controller will receive a software update to eliminate erroneous fault codes and ensure its proper
function. After the software update, the truck will require a recalibration drive for the steering angle sensor.
Please contact an authorized DTNA dealer to arrange to have the campaign performed and to ensure that parts
are available at the dealership. To locate an authorized dealer, go to Daimler-TrucksNorthAmerica.com/
Contact-Us/. Scroll down to “Locate a Dealer,” and select the appropriate brand. The campaign will take
approximately one hour and will be performed at no charge to you.
This Field Service Campaign will terminate on June 30, 2022. Please make sure the campaign is completed
prior to this date. Work completed after this date will be done at the customer’s expense.
As stated in the terms of your express limited warranty, Daimler Trucks North America LLC will not pay for any
damage caused by failure to properly maintain your vehicle. Daimler Trucks North America LLC considers the
work necessary under this campaign to be proper maintenance and will, therefore, not pay for any damage to
your vehicle caused by your failure to have the repairs that are the subject of this campaign performed in a
reasonable time.
Contact the Warranty Campaigns Department at (800) 547-0712, e-mail address
[email protected], or the Customer Assistance Center at (800) 385-4357, if you have
any questions or need additional information.
WARRANTY CAMPAIGNS DEPARTMENT
Enclosure

Page 3

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

Work Instructions
Subject: Cascadia/49X ABS MBSP+ Controller
Software Update
Models Affected: Specific Model Year 2019-2022 Freightliner
Cascadia, and Western Star 49X vehicles, manufactured
September 12, 2018, through March 10, 2021.

ABS ECU Software Update
1.

Inspect the base label (Form WAR259) for a campaign completion sticker for SF622 (Form WAR261). The
base label is usually located on the passenger-side door, about 12 inches (30 cm) below the door latch. If
a sticker is present for campaign SF622, no work is needed. If there is no sticker, proceed with the steps
below.

2.

Confirm that the vehicle’s ABS ECU part number is listed in Table 2.

400 864 815 0

ABS ECU Part Numbers Covered by SF622
400 864 821 0

400 864 825 0

400 864 816 0
400 864 817 0

400 864 822 0
400 864 823 0

400 864 826 0
400 864 827 0

400 864 818 0
400 867 119 0
400 867 120 0

400 864 824 0
400 867 128 0
400 867 129 0

400 864 828 0
400 867 130 0
400 867 131 0

400 867 121 0
400 867 122 0

400 867 125 0
400 867 126 0

400 867 132 0
400 867 133 0

Table 2, ABS ECU Part Numbers Covered by SF622

3.

Park the vehicle on a level surface, shut down the engine, and apply the parking brakes. Chock the tires.

4.

Check for fault code SPN 520272 FMI 13, Steering Ratio Parameters-Out of Calibration, and diagnose
if active. This fault code MUST be inactive before downloading the flash tool. Refer to Service Solution
1033682, New Cascadia ABS Fault code SPN for information.

NOTE: For issues regarding "Flash Tool" download and installation process, call Wabco at 1-855-228-3203, or
email at [email protected].
5.

An mBSP flash tool software of version WNA DiagLib V4.0.0.17 is required to perform this ABS ECU software update procedure. If the mBSP flash tool software is already installed, check the mBSP flash tool
software version; go to "Help", and select "Info about...". See Fig. 1 and Fig. 2.
Is an mBSP flash tool software of version WNA DiagLib V4.0.0.17 installed in the laptop being used for
this update?
YES → Go to step 8, page 18.
NO → Download the latest version of mBSP Flash tool package as follows.

Page 4

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

05/06/2021

f120930

Fig. 1, Opening "Info about Diagnostic Software" Window

Page 5

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

05/06/2021

f120931

Fig. 2, "Info about Diagnostic Software" Window

5.1

Page 6

Go to Wabco website https://www.wabco-auto.com/americas_en/Get-in-touch/Literature.

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

5.2

Scroll down to the "Downloads" section, and click on "mBSP Flash Tool" link. See Fig. 3.

03/31/2021

f120923

Fig. 3, "mBSP Flash Tool" Link in "Downloads" Section

Page 7

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

5.3

Save the ‘mBSP-Flash-Tool.zip’ file to a location on your local hard drive. See Fig. 4.

04/01/2021

f120924

Fig. 4, Saving mBSP Flash Tool Package

.

Page 8

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

6.

Right click on the "mBSP-Flash-Tool.zip" zip file and select "Extract all". See Fig. 5

04/01/2021

f120925

Fig. 5, Extracting the "mBSP-Flash-Tool.zip" File

NOTE: For additional information regarding the mBSP flash tool installation, minimizing laptop disruption during
the installation process, and for links related to adapter driver software, visit DTNA website
https://dtnaecomponents.com/Downloads/mBSPFlashTool/mBSPFlashTool.htm.
7.

Install the mBSP Flash tool as follows.
7.1

In the extracted folder "mBSP Flash Tool", double-click on the "mbspflashtool300en130a.EXE" file.
See Fig. 6 and Fig. 7.

05/06/2021

f120932

Fig. 6, "mbspflashtool300en130a.EXE" File in "mBSP Flash Tool" Folder

Page 9

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

03/16/2021

f120867

Fig. 7, Opening the mBSP Executable File

7.2

Select ’Extract’ to extract the files onto your local hard drive. See Fig. 8.

03/16/2021

f120868

Fig. 8, Extracting the mBSP Executable File

7.3

When the extraction is finished, a pop-up window will ask if you want to launch ’Setup.exe.’
Select ’Yes.’ See Fig. 9.

03/16/2021

f120869

Fig. 9, Launching the Set-Up of the mBSP Executable File

Page 10

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

7.4

When asked to ‘Select Setup Language,’ choose English and select ’OK.’ See Fig. 10.

03/16/2021

f120870

Fig. 10, Language Selection

7.5

The pop-up window ‘Welcome to the mBSP Flash Tool Setup Wizard’ will appear. Select ’Next.’
See Fig. 11.

03/16/2021

f120871

Fig. 11, Navigating the mBSP Flash Tool Setup Wizard

Page 11

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

7.6

At the ‘License Agreement’ pop-up window, choose ‘I accept the agreement’ and then select ’Next."
See Fig. 12.

03/16/2021

f120872

Fig. 12, License Agreement

7.7

An ‘Information’ window will appear; read the information and then select ’Next.’ See Fig. 13.

03/16/2021

f120873

Fig. 13, Navigating Past the Information Window

Page 12

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

7.8

The ‘Select Destination Location’ window will appear. Verify the destination and select ’Next.’
See Fig. 14.

03/16/2021

f120874

Fig. 14, Selecting the Destination Location of the mBSP Flash Tool

7.9

The ‘Select Start Menu Folder’ window will appear, select ’Next.’ See Fig. 15.

03/16/2021

f120875

Fig. 15, Selecting the Start Menu Folder

Page 13

Daimler Trucks
North America LLC

Field Service Campaign

June 2021
SF622A

7.10 At the ‘Select Additional Tasks’ window which will appear next, select ‘Create a desktop shortcut’ and
then select ’Next.’ See Fig. 16.

03/16/2021