Ferrari North America Date: February 2016

Bulletin #: 2309
: . Campaign #:
Technical Information Supersedes:
Section: 10
Model Type: F12 TDF
Model Year: All
Subject: F12 Pre-Delivery Inspection - PDI procedures

Please find attached the procedures and list of inspections to be performed at all times
before the vehicle is delivered to the customer.

The following procedures must be performed exactly as indicated and in the order given,
providing the factory with the information requested.

- IMPORTANT -

This Pre-Delivery Inspection (PDI) procedure may only be performed with a
PC-Tester DEIS updated to at least the following software version (or
subsequent release):

- Module 0 Portal and Troubleshooting 44,
- Module 1 DEIS Diagnostic software 62
- Module 2 Technical Documentation 12
- Module 3 Tools 5

Check the software number and, if necessary, update your DEIS Tester
immediately.

After updating the DEIS, the first vehicle diagnostic cycle must be performed
using a cable connection.

Procedure.

1. Visually inspect condition of vehicle paintwork; repair if necessary (use the specific
“Bodywork defects” form annexed on page 8).

© 2015 Ferrari North America, Inc. All rights reserved. Reproduction or translation in
Technical Department whole or in part is not permitted without
www ferrariusa.com authorization from the publisher. Printed in USA
10.

11.

12.

13.

14.

Ferrari North America

If disconnected, connect the negative pole of the battery and reset the vehicle auto-
adaptive parameters (as described in paragraph F2.01 of the Workshop Manual).

Turn the ignition key to Il and check the letter shown on the DOT MATRIX display:
- If letter “P” (Park Lock) is on the display, go to point 5.

- If letter “N” (Neutral) is on the display, go to point 4.

Re-enable the Park Lock - Gearbox lock device (as described in paragraph E5.11 of the
Workshop Manual).

Remove the engine compartment cosmetic shields (as described in paragraph E3.14 of
the Workshop Manual), then perform the “Battery Certification” procedure (TI 2079)

and compile the relative form. If necessary, remove the battery from the vehicle and
charge using the “SLOW charge” procedure (TI 2078).

Using the DEIS tester, disable the “Logistic Mode” function with diagnostic cycle “150
Complete Logistic Mode” on the NBC ECU (Body Computer Node).

Test the keys and the anti-theft system.

Check that the daytime lights work correctly (depending on market).

Check that the low beam lights work correctly: also check function of the AFS system
(adaptive front lights - if applicable) by turning the steering wheel.

Check the vehicle front lift (if present) is working: also check function of the AFS system
(adaptive front lights - if applicable). With the car raised, the height of the headlight
beam must be the same as with the car lowered.

Check that the high beam lights work correctly.

Check that the brake lights work correctly.

Check that turn indicators work correctly.

Check that door lights, vehicle interior light and luggage compartment lights work
correctly.

TI-2309
TS.

16.

17.

18.

19.

20.

21.

22.

23.

Ferrari North America

Check that the driver side door, dashboard, centre tunnel console and ceiling light unit
button lights are working.

Test the horn.

Check that the power windows work correctly.

Check that the windscreen and headlight wipers work correctly.

Check that the mechanical steering adjustment mechanism works correctly.

Check the mechanical seat functions.

Check function of electric parking brake (EPB); test manual and automatic modes.

Check function of Hi-Fi (if applicable) / Navigation system (if applicable) (see point
35); Set the relative roadside assistance numbers for your market.

Check coolant level and top up if necessary.

TI-2309
24.

25:

26.

27.

28.

29.

a0,

31.

BZ.

33.

34,

35.

36.

Sf,

Ferrari North America

Check power steering fluid level and top up if necessary.

Check brake fluid level and top up if necessary.

Check headlight washer/windscreen washer fluid level and top up if necessary.
Check tyre pressure / TPMS system calibration pressure.

Check tightness of wheel studs with a torque wrench (as described in paragraph D2.01
of the Workshop Manual).

Check that the tow hook is fitted correctly.

Start engine and perform the following:
Perform static function test of AC system.
Test function of electric rear view mirrors.
Select reverse:
- check that the angle of the RH rear view mirror(or the LH mirror on RHD
cars) adjusts automatically;
- check function of the internal electrochromic mirror and the

electrochromic RH and LH rear view mirrors.

Check function of front and rear parking sensors and of front/rear camera (if
applicable).

Using the DEIS tester, perform the “Cancel all DTCs from all ECUs” procedure from
the “Vehicle functions” menu.

Test drive.
Check function of navigation system (if applicable); Set route before starting.

Test drive the vehicle (approx. 20 minutes).

Check function of Stop&Start system (if applicable).

TI-2309
38.

39.

40.

41.

42.

43.

AA.

45.

46.

47.

48.

Ferrari North America

While driving, check that the “Suspension damping decoupling” button and
“Manettino” dial on the steering wheel work correctly.

Check function of telemetry kit (if applicable).

Check function of AC system while driving (dynamic test).

For USA/CND Version only. Take the vehicle into a location with a clear view of the
sky, set the SiriusXM receiver to preview channel 1, and listen to the audio (note that
the preview channel is only available on unactivated SDARS units with no subscription).

Return to workshop.

Check the engine oil level (engine warm and at idle speed) and top up if necessary (as
described in paragraph A3.01 of the Workshop Manual).

With the DEIS tester, check that the VIN number read with the tester matches the VIN
number of the vehicle; if necessary, the VIN number read with the tester may be
modified using the “100 VIN Writing” diagnostic function (password-protected) on
the NCM ECUs (RH and LH engine control nodes).

Check and cancel the errors on all ECUs.

Enter the warranty start date (Check that the language setting on the TFT display is
correct).

Disconnect the battery , wait 30 seconds and reconnect (as described in paragraph
F2.01 of the Workshop Manual). Restore the self-adaptive vehicle parameters (as
described in paragraph F2.01 of the Workshop Manual).

Perform the “SCAN OUT” procedure from the “Vehicle functions” menu with the
DEIS tester before carrying out any further diagnostic operations.

Remove the aerodynamic undertray from the vehicle (as described in paragraph E3.13
of the Workshop Manual).

TI-2309
49.

50.

31.

a2.

53.

54.

55.

36.

afi

38.

ae

60.

61.

62.

63.

64.

Ferrari North America

Visually check for coolant and/or oil leaks in the underbody area and engine
compartment.

Visually inspect engine compartment lines.

Visually inspect engine compartment wiring harnesses.
Visually inspect underbody lines.

Visually inspect exhaust pipe.

Visually inspect fuel tank.

Visually check correct assembly/fastener tightness of: Suspension components, steering
box and axle shaft flanges.

Visually check correct assembly/fastener tightness of: Vehicle earth, engine earth on
chassis earth and gearbox earth on chassis.

Visually inspect condition of brake pads and discs (DO NOT remove wheels).
Check condition of tyres and wheels.

Refit complete aerodynamic undertray complete and cosmetic engine compartment
shields (as described in paragraph E3.13 and E3.14 of the Workshop Manual).

Check function of door and lid locks; adjust if necessary.

Check function of fuel filler flap emergency release and luggage compartment
emergency release; adjust if necessary.

Visually inspect condition of vehicle interior; repair if necessary
Thoroughly clean interior and wash car.

Ensure that the vehicle is delivered complete with the following:
- Identification and Type Approval plates

- License plate holder
- Toolkit

TI-2309

Ferrari North America

- on-board documentation (Owner's Manual, Quick Reference Guide, Warranty
Booklet, Safety Device Booklet and Battery Conditioner Card), second vehicle key and
Code Card, and any material related to options.

- IMPORTANT -

Confirm that the operations listed above have been carried out correctly
with the “Pre-Delivery Inspection - PDI” form (enclosed on pages 6 and 7),
compiled in full and signed by the Aftersales Manager of your Service
Centre.

After completing an inspection, ALWAYS open an ROL (Red On Line),
indicating “PDI Form Info” as the cause, and attach the duly completed
“PDI Pre-Delivery Inspection” form, together with the parameter and error
printout files requested in points , 34 and 47, and the “Battery state
certification” form (TI 2079 / 2230). The procedure for “Testing zero load
electric absorption” is given in paragraph F2.14 of the Workshop Manual).

You will also be required to open a separate individual ROL with the
description “PDI Fault Info” for each fault encountered during the
inspection procedure, indicating the respective operation number as cited

Pr)

in the “PDI Pre-Delivery Inspection” form; Attach all documentation

necessary, including photographs if needed.

Thank you for your co-operation.

TI-2309

Pre-Delivery Inspection - PDI form

Page 01 of 02

Model

Updated on

January 2016

Chassis number:

Dossier creation date:

Job order No.:

Notes:

Description of inspection / operation:

Performed Performed R.O.L. N°

OK

NOTOK = (if NOT OK)

.- Condition of vehicle paintwork.

7
2. - Connect battery and reset vehicle parameters.
3. - Check Park Lock device.

4. - Reset Park Lock device.

5. - “Battery Certification” procedure.
6. - Disable “Logistic Mode”.

7.- Test keys, etc.

8. - Daytime running lights.

9. - Low beams.