NISSAN
BULLETIN
2014 Rogue Push Button Ignition Switch
Quality Hold: Dealer Service Action
Reference: PC300
Date: June 18, 2014
Attention: Dealer Principal, Sales, Service & Parts Managers

*****Dealer Announcement*****
Nissan is conducting a dealer inventory service action to replace the push button ignition
switch on 158 specific 2014 Rogue vehicles identified in SERVICE COMM. These vehicles are
either currently in dealer inventory or assigned and in transit to the dealer.
The subject push button switch may have been manufactured out of specification and could
malfunction.
IMPORTANT: Dealers must not sell any affected 2014 Rogue vehicles in dealer
inventory subject to this service action until the push button ignition switch has
been replaced.
PLEASE FOLLOW THE ATTACHED REPAIR INSTRUCTIONS:




Once the vehicle has been repaired, the vehicle can be released for sale. The service
department should file a warranty claim for this repair in a timely manner so it can
be closed on SERVICE COMM.
Repair parts will be automatically shipped and arrive at dealers by Saturday, June
21st.
Dealers do not need to order parts for this repair activity

***** Vehicle Identification – Dealer Inventory *****
158 2014 Rogue vehicles are subject to this dealer inventory service action and can be
identified through two methods:



SERVICE COMM – Beginning June 18th, dealer service departments can
complete an inquiry on SERVICE COMM – I.D. PC300 - to determine if a
vehicle is subject to this dealer inventory service action.
VIN List – As a courtesy, posted with this announcement is a list of affected
dealer inventory VINs by region, district, and Dealer Code.

***** Dealer Responsibility *****
It is the dealer’s responsibility to check SERVICE COMM -I.D. PC300- for the status on
each 2014 Rogue vehicle which is currently in inventory. Nissan requests dealers to perform
this repair on vehicles in inventory prior to being retailed to ensure customer satisfaction.

***** Repair Procedure *****
This repair procedure will be available on ASIST and NNAnet.com.
 ASIST – Go to “Tech Support Info” on the left column of the ASIST opening page.
Under “Tech Support Info”, select “Inventory Vehicle Actions”. A new window will
open where you may access the technical procedures.
 NNAnet.com –This procedure can be found on NNAnet.com under My Documents in
the following categories:
o Parts>Campaigns>
o Sales>Campaigns>
o Service>Campaigns>
Thank you for your prompt attention to this matter and we apologize for the
inconvenience.
NISSAN NORTH AMERICA, INC.
Aftersales DIVISION

DEALER SERVICE PROCEDURE
1. Remove Front Air Control from center
of dash and gently rest it on the
center console.


Use a protective rag on center
console below the front air
control.



Starting from the bottom, pull
out and up to release the clips
and pawls retaining the front air
control as shown in Figure 1.



Do not unplug the front air
control connectors

2. Remove Instrument Finisher B from
dash as shown in Figure 2.

Pull out
and up
Figure 1
Instrument Finisher
B assembly

Figure 2

3. Disconnect Push-Button Ignition
switch and NATS antenna amp
connectors from Instrument
Finisher B assembly as shown in
Figure 3.

Push-Button
Ignition switch
NATS antenna
amp connector

Figure 3

4. Remove Push-Button Ignition switch
from Finisher B assembly as shown in
Figure 4.


Disengage the three PushButton Ignition switch retaining
clips while pushing on the face
of the switch.



Do not remove the NATS
antenna amp (chrome ring
around Push-Button Ignition
switch) from Instrument
Finisher B.

PushButton
Ignition
switch

Clip

Clip

Clip

Push switch up through
Instrument Finisher B
Figure 4

Push new switch
into Instrument
Finisher B assembly
5. Install new Push-Button Ignition
switch in Instrument Finisher B
assembly as shown in Figure 5.
Note: An audible click sound will be
heard when the Push-Button Ignition
switch is fully seated in the
Instrument Finisher B assembly.

6. Reconnect Push-Button Ignition switch
and NATS antenna amp connectors.
7. Reinstall Instrument Finisher B and
the Front Air Control in reverse order.

Figure 5

PARTS INFORMATION
DESCRIPTION

PART #

QUANTITY

Push-Button Ignition Switch Assembly

25150-4BJ0A

1

CLAIMS INFORMATION
Submit claim using the following claims coding:
Work Order Line Type: “CM” Campaign
Campaign ID: PC300
Claim Type:
PNC:
Symptom:
Diagnosis:
Description:

Replace Push-Button
Ignition switch.

CM
PC300
ZZ
99
Op Codes
Flat Rate
Time
PC3000

0.2 Hrs.

Parts
Required
on claim

Expense
Code
Required

Yes

No