Classificatio n:

Reference:

RS13-007

Date:

NTB13-044

April 10, 2013

2004 – 2006 TITAN KING CAB; AIR BAG LIGHT ON, SEAT BELT
INOPERATIVE, OR REAR AUDIO SPEAKERS INOPERATIVE
APPLIED VEHICLES:

2004 – 2006 Titan (A60) King Cab models only

This bulletin is to be used only for vehicles that have already had campaign R0616
performed (NTB07-009 – Titan Rear Door Harness Voluntary Recall Campaign).

IF YOU CONFIRM
The red Air Bag warning lamp is ON,
and/or
The driver or front passenger seat belt is not working correctly,
and/or
The rear audio speakers are not working correctly,
and/or
The customer has requested an inspection of the above items,

ACTIONS
1. Check Service Comm to determine if Campaign R0616 has been performed.
• If campaign R0616 has not been performed, this bulletin does not apply.
2. Follow the Repair Flow-Chart on the next page.
NOTE: This Service Bulletin provides inspection procedures specifically for vehicles that
have already had campaign R0616 performed (NTB07-009 – Titan Rear Door Harness
Voluntary Recall Campaign).
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/40

REPAIR FLOW-CHART

NO

Check Service Comm. Has campaign R0616 been performed?
(NTB07-009 – Titan Rear Door Harness Voluntary Recall Campaign)
YES

This bulletin
does not apply
Perform campaign R0616,
if open in Service Comm.

Follow this flow chart for the left side door,
then follow it again for the right side door:

(NTB07-009 – Titan Rear
Door Harness Voluntary
Recall Campaign)

Determine repair for each side
before starting repairs.

NG
Replace wire harness
and seat belt.
page 7.

Perform inspection 1
(seat belt retractor); page 5.
OK

Use CONSULT-III plus
to check and clear
DTCs for the NG side.

Perform inspection 2
(air bag light / codes); page 5.
OK

NG
Replace wire harness;
page 7.
Use CONSULT-III plus
to clear DTCs for the
NG side.

NG
Replace wire harness;
Page 7.

Perform inspection 3
(operation of rear door
speakers) page 6.
OK

Return vehicle to the
customer – no repair is
needed

2/40

NTB13-044

PARTS INFORMATION

DESCRIPTION

PART NUMBER

Body Harness (Drivers Side)

QTY
IF NEEDED

1

See NOTE below

Body Harness #2 (Passenger Side)
See NOTE below

Use the VIN and the electronic
parts catalog (FAST or equivalent)
to find the correct P/N.

1

Front Seat Belt – Right
(Passenger Side)

1

Front Seat Belt – Left
(Drivers Side)

1

NOTE: Order the body harness indicated in the electronic parts catalog. Your order will
be automatically superseded to the appropriate service harness part number. As noted
in steps 45 and 67 (pages 28 and 39), service harnesses have some connectors taped
to the harness. Those connectors may or may not be utilized in the repair, depending
upon the optional equipment on the vehicle being serviced.

3/40

NTB13-044

CLAIMS INFORMATION
Submit a (CM) type line claim using the following claims coding:
DESCRIPTION
Perform Inspection Only

OP CODE
PC1986

FRT
0.3 hrs

DESCRIPTION
Inspect and RPL Harness Driver Side

OP CODE
PC1980

FRT
2.4 hrs

OR:

And, in Combination Only IF Necessary, use the following Op Codes:
DESCRIPTION
Additional Allowance for Center Console
(if present)
Additional Allowance for SRS Curtain Airbag
(if present) for one side only

OP CODE
PC1983

FRT
0.3 hrs
0.4 hrs

PC1985

OR:
DESCRIPTION
Inspect and RPL Harness Passenger Side

OP CODE
PC1981

FRT
2.6 hrs

And, in Combination Only IF Necessary, use the following Op Codes:
DESCRIPTION
Additional Allowance for Center Console
(if present)
Additional Allowance for SRS Curtain Airbag
(if present) for one side only

OP CODE
PC1983

FRT
0.3 hrs

PC1985

0.4 hrs

OP CODE
PC1982

FRT
3.4 hrs

OR:
DESCRIPTION
Inspect & RPL Both Driver Side and
Passenger Side Harnesses

And, in Combination Only IF Necessary, use the following Op Codes:
DESCRIPTION
Additional Allowance for Center Console
(if present)
Additional Allowance for SRS Curtain Airbag
(if present) for both sides

OP CODE
PC1983

FRT
0.3 hrs

PC1984

0.8 hrs

Expense code:
EXPENSE CODE
DESCRIPTION
502
Rental Vehicle
* Maximum rental amount is $35.00 per day.

MAX AMOUNT
3 Days

NOTE: Seat belt retractors with seat belt pretensioners should be disposed of in
accordance with local and state regulations.
4/40

NTB13-044

SERVICE PROCEDURE
Inspection Procedure 1 (Front Seatbelt Retractors)
Perform this inspection for both the left and right side front seatbelt retractors.
1. Extend (pull out) the front seat belt, and then let it retract (pull back).
2. Confirm the seat belt extends and retracts.
NG: Replace the seat belt and wire harness for that side (page 5).
OK: Go to Inspection Procedure 2.

Inspection procedure 2 (Air Bag Warning Light / Codes Stored)
1. Turn the ignition ON and observe the air bag warning light:
•

Light comes on for 7 seconds and then goes out: OK, go to Inspection Procedure 3
(next page).

•

Light stays ON or blinks: NG, go to next step (step 2).

•

Light does not come on at all: The warning light is not working correctly. This
condition is not covered by this campaign. Use the Service Manual and standard
warranty procedures to repair the warning light before proceeding.

2. Connect CONSULT-III plus to the vehicle and retrieve DTCs
Codes Stored

Codes Stored

(Driver Side)

(Passenger Side)

B1086; B1087; B1088; B1089

B1081; B1082; B1083; B1084;
B1019

Replace driver side (left side)
wire harness (page 5).

Replace passenger side (right
side) wire harness (page 5).

If other codes are stored: This
bulletin does not apply for
DTCs other than the above

If other codes are stored: This
bulletin does not apply for
DTCs other than the above

5/40

NTB13-044

Inspection Procedure 3 (Rear Door Speakers)
Perform this inspection for both the left and right side rear door speakers.

1. Turn the audio system ON.

2. Confirm sound is coming from the rear door speaker.

NG: Replace the wire harness for that side (page 5).
OK: Inspection End.

If all 3 inspection procedures check OK, no repair is needed

6/40

NTB13-044

Harness Replacement (includes seat belt replacement, if needed)

NOTE:
• There are several model variations (power seats, audio, side air bag, navigation,
etc). Due to these variations the harness removal photos in this procedure may not
have the exact interior trim, connectors, and harness mounting locations as the
vehicle you are working on.
•

It is recommended that you mark the harness mounting location during disassembly.

Floor and Rear Door (Left and/or Right Side)
•

This portion of the procedure is for the sections of the harness that are on the floor
of the vehicle (under the carpet) and inside the rear door.

•

The photos in this portion of the procedure are of the left side (driver side). If you are
working on the right side (passenger side) the photos are a mirror image.

1. Write down the radio station presets.

Presets
A
B
C

1

2

3

4

5

6

2. If equipped with power seats; move the seats to the “mid-point” position (half-way
between full forward and full rearward).

3. Put the gear selector in the Neutral position and block the wheels so the vehicle will not
move.

4. Turn the ignition to the OFF position and disconnect both battery cables—negative
cable first.

7/40

NTB13-044

5. Remove the front seat.

a. Remove the 4 seat mounting bolts.

b. Disconnect all of the seat electrical
connectors.
Front bolt
(1 of 2)

c. Remove the seat from the vehicle and
place it in a clean area.

Rear bolt
(1 of 2)

Figure C1

6. If equipped; remove sub woofer or navigation control unit.

Sub Woofer—under driver’s seat

a. Disconnect the electrical connector.

Bolt
Bolt

b. Remove the 3 mounting bolts.

c. Remove the sub-woofer from the
vehicle.

Bolt
Connector

Figure C2

8/40

NTB13-044

Navigation Control Unit—under passenger
seat

Cover bolts

a. Remove the control unit cover;
2 bolts.

Figure C3

b. Disconnect the electrical
connectors.

Bolt

Bolt

c. Remove the 3 mounting bolts.

Bolt

d. Remove the control unit from the
vehicle.
Electrical connectors

Figure C4

9/40

NTB13-044

7. If equipped with front bench seat (shifter on steering column), remove the center seat
and cup holder:

Finisher

a. Remove the finisher at the rear of
the center seat.

Figure C5

a. Remove the 4 center seat mounting
bolts.
Rear bolt
(1 of 2)

b. Remove the seat from the vehicle and
place it in a clean area.
Front bolt
(1 of 2)

Figure C6

Cup holder