NHTSA ID Number: 10191734
Manufacturer Communication Number: No. 15-21-1
TSB/Document Date: 2021-05-05
Summary
Porsche service campaign information for Workshop Campaign WMA5 - Updating Software for Various Control Units.
Service
Technical Information
15/21
ENU
WMA5
9
WMA5 - Updating Software for Various Control Units (Workshop Campaign)
Revision:
This bulletin replaces bulletin Group 9 15/21 WMA5, dated March 26, 2021.
Model Year:
2020
Important:
CRITICAL WARNING -This campaign includes steps where control unit(s) in the vehicle will be
programmed with the PIWIS Tester. The vehicle voltage must be closely monitored and maintained
between 13.8 volts and 14.8 volts during this programming. Failure to maintain this voltage could result
in damaged control unit(s). It is therefore advised to operate the Deutronics Power Supply (VAS 5908) in
“SUPPLY MODE” with a voltage setting of 14.6 volts and the Air Conditioning System Blower switched
OFF, followed by regular checks of the power supply status, voltage, and vehicle voltage. Certain steps of
this campaign may not be possible until the power supply voltage setting is adjusted then verified by the
PIWIS Tester. Damage caused by inadequate voltage during programming is not a warrantable defect.
The technician must verify the actual vehicle voltage in the PIWIS Tester before starting the campaign and
also document the actual voltage on the repair order.
Model Line:
Taycan (Y1A)
Concerns:
Software update (software version VR12.1.1)
Information:
Software optimizations are available for various control units for the Taycan.
An overview of the new features that will be implemented with the software update can be found in the
attachment under Technical Information 'Overview of new features implemented by the software
updates'.
Action required: •
•
Update the software for the following control units using the PIWIS Tester with software version
40.000.045 (or higher) installed or USB storage medium. For details of affected control units, see
overview below.
Replace Owner's Manual in the on-board folder in the vehicle with an updated version.
Information
During this campaign, the VR12.1.1 software version will be installed on the affected vehicles. The
prerequisite for this is that the previous VR8.7 software version is installed on the vehicle. In order to
ensure that the software updates are installed in the correct order on all vehicles - regardless of whether
or not the VR8.7 software version is already installed - campaigns WLG2 and WLG6 for programming
the VR8.7 software version were completed with the introduction of this campaign WMA5 and the
corresponding programming scopes were transferred to this campaign.
AfterSales
Apr 15, 2021
Page 1 of 40
9
Service
WMA5
ENU
Technical Information
15/21
Depending on whether or not the previous VR8.7 software
version must first be programmed on the relevant vehicle
as a prerequisite for the subsequent programming of the
VR12.1.1 software version, the vehicles were assigned
to the required campaign scope. Before carrying out the
campaign, the scope of the campaign assigned to the
relevant vehicle must therefore be checked and carried
out accordingly.
Information
After carrying out this campaign WMA5, carry out
Evolution Taycan Software Versions
campaign WMA7 so that the Porsche
Mobile Charger
Connect software is also version VR12.1.1. See Technical Information 'WMA700 WMA7 Workshop
campaign - Performing software update for charger (Porsche Mobile Charger Connect)'.
Overview of control units for software version VR12.1.1
Programming time
Control unit
Sequence 1: Combined software update
for various control units
(Update via PIWIS Tester)
approx. 125 minutes
Includes:
Distance measuring sensor control unit
(ACC)
Front-end electronics control unit
(BCM1)
Rear-end electronics control unit (BCM
2)
Radar sensor for front corner radar
Lane Change Assist control unit, left
and right
Central control unit for assistance
systems (zFAS)
Airbag control unit
Reversing camera
Interior surveillance sensor
Seat occupancy detection
Weather sensor
Apr 15, 2021
Page 2 of 40
AfterSales
Action required
program
code
Service
Technical Information
15/21
ENU
WMA5
9
Control unit for garage door opener
Rear lid proximity sensor control unit
Windscreen wiper motor
Sequence 2: Combined software update
for various control units
(Update via PIWIS Tester)
approx. 120 minutes
Includes:
Battery sensor for 12 V vehicle electrical system battery
High-voltage charger (OBC), 11 kW
High-voltage battery control unit (BMCe)
High-voltage DC charger (booster)
HV voltage converter
Control unit for chassis control (PASM)
Power steering (EPS) control unit
Brake electronics (PSM) control unit
Control unit for steering column
adjustment
Control unit for rear axle steering
Rear lid control unit
Air-conditioning control unit
Rear-differential lock control unit
Thermal management control unit
(TME)
Electric passenger compartment
heater (PTC)
Gateway control unit
Head-up display
Instrument cluster
Over-the-air (OTA) control unit
Engine electronics (DME) control unit
Power electronics, front and rear
Transmission electronics control unit
(EGS)
AfterSales
Apr 15, 2021
Page 3 of 40
9
Service
WMA5
ENU
Technical Information
15/21
Roll stabilization control unit (PDCC)
Headlight, left and right
Sequence 3: Combined software update
for various control units
(Update via PIWIS Tester)
approx. 130 minutes
Includes:
Multi-function steering wheel
Control unit for memory seat
adjustment (driver side)
Additional instrument control unit
(stopwatch)
Door control unit, front and rear
Control unit for exterior acoustics
(eSound)
Control unit for interior acoustics
(iSound)
Display and operator control unit in rear
center console
Connect control unit
Brake booster control unit (eBKV)
Night vision system control unit
Control unit for Tyre Pressure Monitoring (TPM)
Control unit for memory seat
adjustment (passenger side)
Control unit for rear spoiler
Sequence 4: Combined software update
for various control units
(update via PIWIS Tester and USB storage
medium)
approx. 60 minutes
Includes:
Porsche Communication Management
(PCM) central computer
Loudspeaker booster
Front display and operator control unit
(central display)
Apr 15, 2021
Page 4 of 40
AfterSales
Service
Technical Information
15/21
ENU
WMA5
9
Passenger display
Operator control unit in the front center
console
Affected
vehicles:
Only vehicles assigned to the campaign (see also PCSS Vehicle Information). This campaign affects
5,235 vehicles.
Parts required
Parts Info:
Owner's Manual
An overview of the required Owner's Manuals is provided under Technical Information 'WMA700
Overview of order numbers for Driver's Manuals'.
Required tools
Information
The Taycan (Y1A) is equipped as standard with a lithium starter battery.
Lithium starter batteries must only be charged using a suitable battery charger that has a current
and voltage-controlled charge map.
For further information about the battery chargers to be used, see Workshop Manual '270689
Charging battery/vehicle electrical system'.
Information
A blank or re-writable USB storage medium is additionally required for installing the onboard Owner's
Manual.
If no additional USB storage medium is available for carrying out this campaign, a replacement USB
storage medium (e.g. Part No. V04014999WW000) must be purchased. The costs for the USB storage
medium cannot be invoiced under the workshop campaign number.
Tools:
•
•
•
•
Battery charger with a current rating of at least 90 A and - if required - also with a current- and
voltage-controlled charge map for lithium starter batteries, e.g. VAS 5908 90 A battery
charger
9900 - PIWIS Tester 3 with software version 40.000.045 (or higher) installed.
USB storage medium Type A+C 32 GB (for PCM update), Part No. V04014999WW000
USB storage medium, type C (for onboard Owner's Manual update), e.g. Part No.
V04014999WW000
AfterSales
Apr 15, 2021
Page 5 of 40
9
Service
WMA5
ENU
Technical Information
15/21
Information
The central computer (PCM) software update is performed using a USB storage medium. The software
version that is specific to each region must be downloaded using the software tool PiUS (Porsche integrated Update Service) and installed on a blank USB storage medium.
Pay particular attention to the following:
•
For this PCM software update, the USB storage medium USB Type A+C 32 GB with the part number
V04014999WW000 must be used.
•
To use the software tool, one blank or re-writable USB storage medium is required for each individual software.
•
The software available in PiUS must only be used in accordance with the instructions provided in a
Technical Information published for this purpose.
The software mentioned here must only be used on the vehicles assigned to the campaign. Damage
to the central computer cannot be ruled out if the software is used on other vehicles.
You will find further information on how to install and use the PiUS software tool in the PPN portal under
*PiUS (Porsche integrated Update Service) goes live*.
Overview of PiUS software versions – PCM update VR12.1.1
Part No.*
Designation
– Region
Vehicle assignment
9J1919360C
PCM update software
– Europe
– ROW
I-no. ER1/ER2
9J1919360D
PCM update software
– North America
– Mexico
I-no. ER3/ER4
9J1919360E
PCM software update
– Japan
– China
– Korea
– Taiwan
I-no. ER5/ER6/ER7/ER8
Preparatory work
NOTICE
Fault entry in the fault memory and control unit programming aborted due to undervoltage.
•
Increased current draw during diagnosis or control unit programming can cause a drop in voltage, which
can result in one or more fault entries and the abnormal termination of the programming process.
Before starting control unit programming, connect a suitable battery charger with a current rating of at
least 90 A to the vehicle.
Apr 15, 2021
Page 6 of 40
AfterSales
Service
Technical Information
15/21
ENU
WMA5
9
NOTICE
Control unit programming will be aborted if the WiFi connection is unstable.
•
An unstable WiFi connection can interrupt communication between the PIWIS Tester and the vehicle
communication module (VCI). As a result, control unit programming may be aborted.
During control unit programming, always connect the PIWIS Tester to the vehicle communication module
(VCI) via the USB cable.
NOTICE
Programming interrupted
•
Malfunctions in control unit
•
Risk of damage to control unit
Route the line between the vehicle communication module (VCI) and diagnostic socket on the vehicle
without tension and make sure that the connector is inserted fully into the diagnostic socket.
Check that the rechargeable battery for the PIWIS Tester is charged sufficiently. Connect the PIWIS Tester
to the power supply unit if necessary.
Information
To carry out the campaign, the PIWIS Tester must be online and logged into the Porsche Partner Network
(PPN).
AfterSales
Apr 15, 2021
Page 7 of 40
9
Service
WMA5
ENU
Technical Information
15/21
Information
Use the new PIWIS Tester data cable to carry out the
campaign. The difference between the old PIWIS Tester
data cable -1- and new PIWIS Tester data cable -2data cable is shown in the illustration.
If the connection between the vehicle and PIWIS Tester is
interrupted, check the data cable for the PIWIS Tester for
signs of damage. If the data cable is damaged, it must be
replaced. To do this, follow the instructions in the PPN
for "Returning faulty USB cable caps" (PPN portal > Dr
Ing. h.c. Porsche AG > Aftersales > Workshop > PIWIS >
Documents).
Information
The procedure described here is based on the PIWIS
Tester 3 software version 40.000.045.
The PIWIS Tester instructions take precedence and in the
event of a discrepancy, these are the instructions that
must be followed.
A discrepancy may arise with later software versions for example.
PIWIS Tester data cable
Information
The state of charge of the high-voltage battery should not be less than 30% or more than 80% for the
software update.
Work Procedure: 1
Connect a suitable battery charger, e.g. Battery charger 90A, to the jump-start terminals in the
luggage compartment and switch it on.
Information
To prevent any excessive and potentially noticeable heating of the charging clamp of the negative
cable while charging the 12-volt vehicle electrical system battery using an external battery charger,
always check the following points:
Apr 15, 2021
Page 8 of 40
•
Always connect the charging clamp of the negative cable vertically from above to the ground
point for the external power connection. Make sure that the charging clamp cable is routed
loosely to prevent the charging clamp from tilting sideways at the ground point.
•
When connecting the charging clamp, make sure that it is a sufficient distance away from
peripheral parts (e.g. pneumatic supply line for air-spring strut).
•
Before raising the vehicle using a lifting platform, always disconnect the battery charger
completely from the vehicle to prevent the connecting line of the charging clamp from
becoming taut and prevent the charging clamp from tilting sideways at the ground point.
AfterSales
Service
Technical Information
2
15/21
ENU
WMA5
9
Position the driver's key with the back facing
forward upright between the holding struts in the rear
cupholder (emergency start tray) to guarantee a
permanent radio link between the vehicle and remote
control Emergency start tray.
Emergency start tray
NOTICE
Control unit programming will be aborted if the driver's key is not recognized
•
If the driver's key is not recognized in the vehicle, programming cannot be started or will be interrupted.
Position the driver's key with the back facing forward upright between the holding struts in the rear
cupholder (emergency start tray) to ensure a permanent radio link between the vehicle and remote
control.
3
Connect the 9900 - PIWIS Tester 3 to the Vehicle Communication Module (VCI) via the USB cable.
Then, connect the Communication Module to the vehicle and switch on the PIWIS Tester. Due to the
long programming time, operate the
PIWIS Testervia the power supply.
4
Establish operational readiness (switch on ignition).
5
On the PIWIS Tester start screen, call up the 'Diagnostics' application.
The vehicle type is then read out, the diagnostic application is started and the control unit selection
screen is populated.
6
Create vehicle analysis log (VAL) using the PIWIS Tester.
Mark the vehicle analysis log you have just created with the attribute "Pre— VAL" and after carrying
out the campaign, return it using the PIWIS Tester.
Information
Depending on whether or not the previous software version VR8.7 must first be programmed on the
relevant vehicle before programming software version VR12.1.1, the vehicles were assigned to the
required campaign scope. Before carrying out the campaign, the campaign scope assigned to the
relevant vehicle must therefore be checked and carried out accordingly.
AfterSales
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: No. 15-21-1
Replacement Service Bulletin Number:
MFR Communication Date: 2021-04-15
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.