14/26

NTB20-096A

25.

Toward the end of the reprogram, the CONSULT will show an Error Code
“Reprogramming Ignition off Error” and the vehicle ignition will turn off.
a) Turn the ignition ON, engine OFF.
b) Select Retry.

XXXXXXX
XXXXXXX

XXXXXXXXXXXX

XXXXXXXXXXXX

Figure 23

15/26

NTB20-096A

26.

If Error Code description “Reprogramming Not Needed” is displayed after another
reattempt, this indicates the reprogramming has successfully completed. Select
Home, and then proceed to step 27 on page 18.
NOTE: If the screen in Figure 24 does not display (indicating that reprogramming did
not complete), refer to the information on the next page.

XXXXXXX
XXXXXXX

XXXXXXXXXXXX

XXXXXXXXXXXX

Figure 24

16/26

NTB20-096A

BCM Recovery:
If reprogramming does not complete and the “!?” symbol displays as shown in
Figure 25:


Check battery voltage (12.0 –
15.5V).



Ignition is ON, Engine is OFF.



External Bluetooth® devices are
OFF.



All electrical loads are OFF.



Select Retry and follow the on
screen instructions.

XXXXXX
XXXXXX

XXXXXXXXXXX

XXXXXXXXXXX

NOTE: Retry may not go through on
first attempt and can be selected
more than once.

Figure 25

If reprogramming does not complete and the “X” symbol displays as shown in
Figure 26:


Do not disconnect the VI
or shut down C-III plus if
reprogramming does not
complete.



Check battery voltage (12.0 –
15.5V).



XXXXXX
XXXXXX

CONSULT A/C adapter is plugged
in.



Ignition is ON, Engine is OFF.



Transmission in Park.



All C-III plus / VI cables are
securely connected.



All C-III plus updates are installed.



Select Home, and then restart the
reprogram procedure from the
beginning.

XXXXXXXXXXXX

XXXXXXXXXX

Figure 26

17/26

NTB20-096A

Configure the BCM
IMPORTANT: Approximately 90 seconds after the reprogram has completed, the BCM will
enter battery saver mode and will turn the ignition off.


Periodically check the vehicle to verify the ignition is still on and turn the ignition to
the ON position as needed.



This condition will no longer be present after the BCM has been configured.

27.

Repeat steps 4 - 11 on pages 3 - 6.

28.

Select After ECU Replacement under VEHICLE CONFIGURATION.

Figure 27

18/26

NTB20-096A

29.

Select Manual selection.

Figure 28
30.

Select the Setting Value for each item that was documented in step 13, and then
select Next.

Figure 29

19/26

NTB20-096A

31.

Verify the ignition is ON, engine OFF, and then select OK to write the configuration.

Figure 30

32.

Allow the configuration to write to the BCM.

Figure 31

20/26

NTB20-096A

33.

Select End.

Figure 32

Register TPMS Sensors
34.

Register the TPMS sensors.


For TMPS sensor ID registration, refer to the Electronic Service Manual (ESM)
section: SUSPENSION > ROAD WHEELS &TIRES > BASIC INSPECTION > ID
REGISTRATION PROCEDURE.

21/26

NTB20-096A

Erase DTCs
35.

Select Diagnosis (All Systems).

Figure 33

36.

Select Automatic Selection(VIN).

Figure 34

22/26

NTB20-096A

37.

Allow the CONSULT to perform automatic VIN selection.

Figure 35

38.

Confirm the VIN or Chassis # is correct, and then select Confirm.

XXXXXXXXXXXXXXX

Figure 36

23/26

NTB20-096A

39.

Select ERASE.

Figure 37

40.

Select Execute.

Figure 38

24/26

NTB20-096A

41.

Select Close.

Figure 39

42.

Close the C-III plus application.

43.

Remove the VI from the vehicle.

25/26

NTB20-096A

CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID
P0A34

DESCRIPTION
Check Part Number,
Reprogram Not Needed
Reprogram and Configure the Body
Control Module (BCM)

OP CODE

FRT

P0A340

0.3 hrs

P0A341

0.8 hrs

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
December 21, 2020

NTB20-096

March 24, 2021

NTB20-096A

DESCRIPTION
Original bulletin published
Changes were made to pages 6-12 and 19-20.

26/26

NTB20-096A