Tips&Tricks –Multistrada V4 Model Year 2021
no.

1

Symptom

Issues during Top Case
fixing to the plate

Subject

Top Case Kit
Part no.96781531AA

Photo

Notes and Indications - Corrective action
We have received some reports concerning the difficulty in
securing the Top Case (Kit Part no.96781531AA) to the top
plate Part no.8291M033A due to a machining error of the
supplier. In particular, the locking tooth on the upper plate
Part no.8291M033A shows a hole 2mm narrower than
specified. To eliminate this defect, the locking tooth of the
plate must be milled by 2mm in the upper area using a flat file,
as shown in the figure.

2mm

We inform you that the upper plates present inside the kits in
stock have been restored.
After having installed the anti-theft system Kit Part no.96681081AA and enabled it on the BBS control unit,
some malfunctions may occur during activation due to a possible incorrect pin arrangement in the connector
of the wiring branch supplied with the kit.

2

Anti-theft system kit
Part no.96681081AA
malfunction

Anti-theft system kit
Part no.96681081AA

Follow the procedure described below:
1) uncover connector (A) by moving sheath (B) backward;
2) uncover the wiring by removing a portion of insulating tape to make operations easier;
3) check the arrangement of Pins 5 and 6 and the relevant colour on the 8-pin connector. If the pin
arrangement is not correct, extract them working from the front side with a needle inside the groove so
as to lift the retainer and invert them.
4) restore the cloth tape previously removed and the position of the protective sheath (B).

The kits currently in stock have been restored.

SRV-TTB-21-001_Rev.02

STRICTLY CONFIDENTIAL

1

Tips&Tricks –Multistrada V4 Model Year 2021
no.

Symptom

Subject

Photo

ONLY
Multistrada V4S
4

5

Software updates for
Bosch instrument panel
with DDS 2.0 diagnosis
instrument

Precautions during PDI:
installation of the battery
on the vehicle

Software updates for
Bosch instrument panel

Battery assembly

-

Notes and Indications - Corrective action
The new DDS 3.0 diagnosis instrument kits Part no.979000279 are being
distributed and will be delivered within the next few months.
We would like to remind you that in order to carry out software updates of the
Multistrada V4S instrument panel, it is necessary to use the USB cable included
in the DDS 3.0 diagnosis instrument kit.
If you have not received the new diagnosis instrument yet, you can still perform
the update using the DDS 2.0 using any USB cable, type A male-male (this cable
is easily available on the market).
We also inform you that a video has been made showing you the correct use of
the cable. It can be viewed at the following YouTube link:
https://youtu.be/IGbLKyo4B8k.

We have received isolated reports of possible issues concerning the connection of battery negative cable; in
particular, you may find that the negative cable appears to be too long.
To correctly position the battery negative cable, make sure that the cable runs over the main wiring and
makes a bend upstream of the battery negative pole.
For a better understanding, we have made a short video showing the issue described above and the correct
battery installation, which can be viewed at the following link: https://youtu.be/wu1qH4gi4LI.

6

Precaution during the
installation of the heated
handgrip kit part no.
96680702A

SRV-TTB-21-001_Rev.02
2

Heated handgrip kit part
no. 96680702A

We inform you that for the installation of the heated
handgrip kit part no. 96680702A, the main wiring harness
connectors where to connect the heated handgrips, are
positioned below the ignition switch cover as shown in the
figure.

STRICTLY CONFIDENTIAL

Tips&Tricks –Multistrada V4 Model Year 2021
no.

7

Symptom

Possible incorrect
operation of the swinging
system - Top Case
accessory kit part no.
96781531AA

Subject

Photo

Notes and Indications - Corrective action
We inform you that the first Top Case accessory kits part
no. 96781531AA delivered may not operate correctly with
the swinging system, which may seem “too braked”. To
improve this condition, it is possible to insert 4 copper
washers (1) part no. 85250231A on the 4 screws (2)
retaining the bottom plate to the top one.
For a better understanding of the assembly procedure of
the Top Case accessory kit, a video has been made which
can
be
viewed
at
the
following
link:
https://youtu.be/DVEHKVvdKQI.

Top Case
Part no.96781531AA

All Top Case kits in stock will be restored by February.

8

Ducati Quick Shift (DQS)
malfunctioning and no
indication on the
instrument panel of the
engaged gear

We have received isolated reports about the Ducati Quick Shift (DQS) not working properly, and about the
missing indication of the engaged gear on the instrument panel, with gear sensor plausibility error P0919
being stored.
Final
drive

Some analyses showed that this condition occurred following a change in the final drive gear ratio (Z15
sprocket installed instead of Z16 as designed).
As already emphasised during the technical training, we remind you to avoid any modification to the final
drive gear ratio (Z16 sprocket and Z42 rear sprocket).

9

Possible switching on of
DSS warning light on
instrument panel

SRV-TTB-21-001_Rev.02
3

Ducati Skyhook
Suspension (DSS)

-

There have been some isolated reports regarding a possible switching on of the “DSS” warning light
on
the instrument panel for the models equipped with Ducati Skyhook Suspension without any errors read by
the diagnosis instrument.
Through the DDS 3.0 diagnosis instrument, enter the “Settings” section of the BBS control unit and perform
the “Calibration of the rear rotary sensor”.

STRICTLY CONFIDENTIAL

Tips&Tricks –Multistrada V4 Model Year 2021
no.

Symptom

Subject

Photo

Notes and Indications - Corrective action
The TPMS system (Tyre Pressure Monitoring System) allows monitoring tyre pressure value: if tyre pressure
deviates by 25% from the set reference value, the TPMS system displays a warning on the instrument panel.
The sensor activates when speed exceeds 35 km/h and tyre pressure is displayed on the instrument panel 1
minute later.
We remind you that, before installing tyre pressure sensors on front and rear wheel rims, they must be coded
through DDS 3.0 diagnosis instrument.

10

Activation procedure for
TPMS tyre pressure
sensor

TPMS
(Tire Pressure
Monitoring System)

To activate TPMS system, follow the procedure indicated below:
1) using DDS 3.0, access the “Self-diagnosis → Settings” section of BBS
control unit;
2) select “Enable/Disable” TPMS;
3) access the “Self-diagnosis → Settings” section of Hands Free control
unit and perform “TPMS code writing” for front and rear wheel sensors
by entering the 8-digit code written above the Qr-Code;
4) access the instrument panel Settings menu and select “Tire Pressure”
to set (and customise) the reference pressure values of the rear and
front tyres. The tyre nominal pressure value specified inside the owner's
manual can be used as a reference.
Explain to the Customer the use of the "Tire Pressure" function to edit the
reference pressure value of the front and rear tyres. The information about
the current pressure value of front and rear tyres is also available inside
instrument panel main menu.

11

Precautions for checking
the engine oil level

SRV-TTB-21-001_Rev.02
4

Level
engine oil

To correctly check the engine oil level, carefully follow the operations described below:
1) The level check should be carried out with warm engine, approximately 15 minutes after the engine has
been turned off.
2) Turn off the engine and wait 10÷ 15 minutes to allow the oil to return completely to the oil sump.
3) Position the motorcycle on level ground with both wheels on the ground and in an upright position.
4) Check the oil level through the sight glass.
If the oil level is below the centre line between the MIN and MAX notches, add oil up to the maximum level
notch.

STRICTLY CONFIDENTIAL

Tips&Tricks –Multistrada V4 Model Year 2021
no.

13

Symptom

Possible lack of paint
adhesion on fuel tank cap

Subject

Fuel tank cap

Photo

Notes and Indications - Corrective action

We would like to inform you that on an initial batch of motorcycles produced, the fuel tank cap could present
a problem of paint adhesion. Starting from frame number ZDM1A00AAMB002445 the supplier has
improved the painting process that avoids this issue.
The fuel tank caps in the spare part warehouse are compliant.

14

Assembly precaution for
the anti-theft system kit
part no. 96681081AA

15

Assembly precaution for
the fuel tank cap kit
Hands Free
part no. 96681021AA

SRV-TTB-21-001_Rev.02
5

Anti-theft system kit part
no. 96681081AA

We inform you that for the installation of the anti-theft
system kit part no. 96681081AA, the main wiring
connector (1) where to connect the anti-theft device, is
positioned near the fuel pump flange, in the front left
area of the fuel tank.

Hands Free fuel tank cap
kit part no. 96681021AA

We inform you that for the installation of the Hands Free
fuel tank cap kit part no. 96681021AA, the main wiring
connector (2) where to connect the Hand Free fuel tank
cap, is positioned near the fuel pump flange, in the front
left area of the fuel tank.

STRICTLY CONFIDENTIAL