January 2021
Dealer Service Instructions for:

Customer Satisfaction Notification W84
Powertrain Software Update
Remedy Available
2014
2017
2017
2017
2017

(KL)
(UF)
(MP)
(KL)
(BU)

Jeep Cherokee
Chrysler 200
Jeep Compass
Jeep Cherokee
Jeep Renegade (AWD)

NOTE: This campaign applies only to the above vehicle equipped with a 2.4L
engine (sales code ED6 or ED8 or EDD or EDE)
NOTE: Some vehicles above may have been identified as not involved in this
campaign and therefore have been excluded from this campaign.

IMPORTANT: Some of the involved vehicles may be in dealer used vehicle
inventory. Dealers should complete this campaign service on these vehicles
before retail delivery. Dealers should also perform this campaign on vehicles in
for service. Involved vehicles can be determined by using the VIP inquiry process.

 Copyright 2021, FCA US LLC, All Rights Reserved(kka)

Customer Satisfaction Notification W84 – Powertrain Software Update

Page 2

Subject
FCA US has determined that 270,667 of the above vehicles may have an engine
that consumes more oil than usual under certain operating conditions like
continuous stop and go driving. The condition results when a combination of
components with certain manufacturing variances are present and the current
engine calibration strategy. While the condition is rare, your vehicle falls within
the population where such variances could cause an oil consumption issue. If your
vehicle is subjected to a low oil condition, the oil indicator lamp on your
instrument panel cluster may illuminate or you will notice an oil level below the
dipstick crosshatch range markings when checking your vehicle’s oil level as
recommended in your Owner’s Manual. If left unaddressed, a low oil condition
can eventually result in a vehicle stall.

Repair
Reprogram the Powertrain Control Module (PCM) on all of the above vehicles
involved, and update the Transmission Control Module TCM) software. Check the
oil level, add if necessary.

Parts Information
68218950AC

1 Quart Bottle, MS-6395, Oil, Engine SAE 0W-20 (MSQ 12)

Parts Return
No parts return required for this campaign.

Special Tools
The following special tools are required to perform this repair:
 NPN

wiTECH MicroPod II

 NPN

Laptop Computer

 NPN

wiTECH Software

Customer Satisfaction Notification W84 – Powertrain Software Update

Page 3

Service Procedure
NOTE: The wiTECH scan tool must be used to perform this customer
satisfaction notification. If the PCM or TCM is aborted or interrupted
during reprogramming, it must be restarted. The PCM and TCM software
must be at the latest software calibration level after completing this
customer satisfaction notification.

1. Open the hood and install a battery charger. Verify that the charging rate
provides 13.0 to 13.5 volts. Do not allow the charger to time out during the
flash process. Set the battery charger timer (if so equipped) to continuous
charge.
NOTE: Use an accurate stand-alone voltmeter. The battery charger volt
meter may not be sufficiently accurate. Voltages outside of the specified
range will cause an unsuccessful flash. If voltage reading is too high, apply
an electrical load by activating the park or headlamps and/or HVAC
blower motor to lower the voltage.
2. Connect the wiTECH micro pod II to the vehicle data link connector.
3. Place the ignition in the “RUN” position.
4. Open the wiTECH 2.0 website.
5. Enter your “User id” and “Password” and your “Dealer Code”, then select
“Sign In” at the bottom of the screen. Click “Accept”.
6. From the “Vehicle Selection” screen, select the vehicle to be updated.

Customer Satisfaction Notification W84 – Powertrain Software Update

Page 4

Service Procedure [Continued]
7. From the “Action Items” screen, select the “Topology” tab.
8. From the “Topology” tab, select the “PCM” module icon.
9. From the “Flash” tab, compare the “Current Electronic Control Unit (ECU)
Part Number” with the “New ECU Part Number” listed.
 If the “Current ECU part Number” is the same as the “New Part
Number”, proceed to Step 14.
 If the “Current ECU part Number” is NOT the same as the “New Part
Number”, continue with Step 10.
10. From the PCM tab, select the latest PCM flash part number. Read the flash
special instructions page. Select “OK” to continue.
11. From the flash ECU agreement page, agree to terms by checking the box.
12. Select “Flash ECU” and then follow the wiTECH screen instructions to
complete the flash.
13. Confirm the software is at the latest available calibration level.
14. Click “View DTCs”, select “Clear All DTCs”, click “Continue” and then click
“Close”.

Customer Satisfaction Notification W84 – Powertrain Software Update

Page 5

Service Procedure [Continued]
15. From the “Action Items” screen, select the “Topology” tab.
16. From the topology screen select “TCM” icon.
17. From the “TCM View” screen select the “Flash” tab. Compare the “Current
Flash Number” with the “New Part Number” listed on the “sort table”. If
the “Current Flash Number” is the same as the “New Part Number”
continue to Step 22. If the part numbers are not the same, continue with
Step 18.
18. From the TCM tab, select the TCM flash part number. Read the flash special
instructions page. Select “OK” to continue.
19. From the flash ECU agreement page, agree to terms by checking the box.
20. Select “Flash ECU” and then follow the wiTECH screen instructions to
complete the flash.
21. Confirm the software is at the latest available calibration level.
22. Click “View DTCs”, select “Clear All DTCs”, click “Continue” and then
click “Close”.
23. Place the ignition in the “OFF” position and then remove the wiTECH micro
pod II device from the vehicle.
24. Remove the battery charger from the vehicle.
25. Check oil level and add as needed.
26. Close the vehicle hood.
27. Return the vehicle to the customer.

Customer Satisfaction Notification W84 – Powertrain Software Update

Page 6

Completion Reporting and Reimbursement
Claims for vehicles that have been serviced must be submitted on the
DealerCONNECT Claim Entry Screen located on the Service tab. Claims paid
will be used by FCA to record Customer Satisfaction Notification service
completions and provide dealer payments.
Use one of the following labor operation numbers and time allowances:
Labor Operation
Number

Time
Allowance

Inspect PCM/TCM Software level
2014 KL, 2017 KL/UF/BU/MP

18-W8-41-81

0.2 hours

Inspect and reprogram PCM and TCM software
2017 KL/UF/BU/MP

18-W8-41-82

0.4 hours

Reprogram PCM and TCM, and perform Adaptation
Learn Procedure (2014 KL Model Only)
18-W8-41-84

1.2 hours

Related Labor Operation
Porter’s time flat fee allowance (2014 KL Model Only)
Fuel Allowance (2014 KL Model Only)

95214453
95140155

$20.00
$8.00

NOTE: See the Warranty Administration Manual, Recall Claim Processing
Section, for complete claim processing instructions.

Dealer Notification
To view this notification on DealerCONNECT, select “Global Recall System” on
the Service tab, then click on the description of this notification.

Owner Notification and Service Scheduling
All involved vehicle owners known to FCA are being notified of the service
requirement by mail. They are requested to schedule appointments for this service
with their dealers. A generic copy of the owner letter is attached.

Customer Satisfaction Notification W84 – Powertrain Software Update

Page 7

Vehicle Lists, Global Recall System, VIP and Dealer Follow Up
All involved vehicles have been entered into the DealerCONNECT Global Recall
System (GRS) and Vehicle Information Plus (VIP) for dealer inquiry as needed.
GRS provides involved dealers with an updated VIN list of their incomplete
vehicles. The owner’s name, address and phone number are listed if known.
Completed vehicles are removed from GRS within several days of repair claim
submission.
To use this system, click on the “Service” tab and then click on “Global Recall
System.” Your dealer’s VIN list for each campaign displayed can be sorted by:
those vehicles that were unsold at campaign launch, those with a phone number,
city, zip code, or VIN sequence.
Dealers should perform this repair on all unsold vehicles before retail
delivery. Dealers should also use the VIN list to follow up with all owners to
schedule appointments for this repair.
VIN lists may contain confidential, restricted owner name and address information that was
obtained from the Department of Motor Vehicles of various states. Use of this information is
permitted for this notification only and is strictly prohibited from all other use.

Additional Information
If you have any questions or need assistance in completing this action, please
contact your Service and Parts District Manager.
Customer Service / Field Operations
FCA US LLC

This notice applies to your vehicle,

CUSTOMER SATISFACTION NOTIFICATION
Powertrain Software Update

[Model Year and Model]
VIN XXXXXXXXXXXXXXXXX

W84

Dear [Name],

LOGO

At FCA US LLC, we recognize that the success of our business depends on the satisfaction of
our customers. We are constantly monitoring the quality of our products and looking for
opportunities to improve our vehicles even after they are sold. Because your long-term
satisfaction is important to us, we are contacting you on important improvements we would
like to make to your vehicle [1]. This will be done at no charge to you.

VEHICLE PICTURE

We are recommending the following improvements be performed on certain [ 2017 Model
Year (UF) Chrysler 200, 2014 (KL) Jeep Cherokee, 2017 (KL) Jeep Cherokee ,2017 (MP)
Jeep Compass, 2017 (BU) Jeep Renegade] vehicles equipped with a 2.4L engine.

YOUR SCHEDULING OPTIONS

WHY DOES MY VEHICLE NEED REPAIRS?
FCA US has determined that some vehicles may have an engine that consumes more oil than
usual under certain operating conditions like continuous stop and go driving. The condition
results when a combination of components with certain manufacturing variances are present
and the current engine calibration strategy. While the condition is rare, your vehicle [1] falls
within the population where such variances could cause an oil consumption issue. If your
vehicle is subjected to a low oil condition, the oil indicator lamp on your instrument panel
cluster may illuminate or you will notice an oil level below the dipstick crosshatch range
markings when checking your vehicle’s oil level as recommended in your Owner’s Manual. If
left unaddressed, a low oil condition can eventually result in a vehicle stall.

1. RECOMMENDED OPTION
Call your authorized Chrysler /
Dodge / Jeep® / RAM Dealership
2. Call the FCA Recall Assistance
Center at 1-800-853-1403. An
agent
can
confirm
part
availability and help schedule an
appointment
3. Visit recalls.mopar.com, scan the
QR code below, or download the
Mopar Owner’s Companion App.

QR Code

Get access to recall notifications,
locate your nearest dealer, and more
through this website or Mopar
Owner’s Companion App. You will be
asked to provide your Vehicle
Identification Number (VIN) to
protect and verify your identity.
DEALERSHIP INSTRUCTIONS
Please reference CSN W84.

HOW DO I RESOLVE THIS CUSTOMER SATISFACTION NOTIFICATION?
FCA US will provide a repair for your vehicle free of charge (parts and labor) that will address
the manufacturing variances that could lead to an abnormal use of excessive oil. To do this,
your dealer will inspect the software level of the Powertrain Control Module (PCM) and
Transmission Control Module (TCM) in your vehicle, and, if necessary, reprogram the PCM
and TCM. The estimated repair time is about a half hour. In addition, your dealer will require
your vehicle for proper check-in, preparation, and check-out during your visit, which may
require more time. Your time is important to us, so we recommend that you schedule a service
appointment to minimize your inconvenience. Please bring this letter with you to your
dealership.
TO SCHEDULE YOUR FREE REPAIR,
CALL YOUR CHRYSLER, DODGE, JEEP OR RAM DEALER TODAY

WHAT IF I ALREADY PAID TO HAVE THIS REPAIR COMPLETED?
If you have already experienced this specific condition and have paid to have it repaired, you
may visit www.fcarecallreimbursement.com to submit your reimbursement request online. [2]
Once we receive and verify the required documents, reimbursement will be sent to you within
60 days. If you have had previous repairs performed and/or already received reimbursement,
you may still need to have the repair performed.
We apologize for any inconvenience, but are sincerely concerned about your satisfaction.
Thank you for your attention to this important matter.
Customer Assistance/Field Operations
FCA US LLC

Mr. Mrs. Customer
1234 Main Street
Hometown, MI 48371

[1] If you no longer own this vehicle, please help us update our records. Call the FCA Recall Assistance Center at 1-800-853-1403 to update your information.
[2] You can also mail in your original receipts and proof of payment to the following address for reimbursement consideration: FCA Customer Assistance, P.O. Box 218004, Auburn Hills, MI 48321-8007, Attention: Recall Reimbursement.